Luminance Brands RIPTIDE CF605BQ00 Manuale utente
Part No. F40BP75720002 Form No. BP7572-2
Revision: 02152021 U.L. Model No.: CF605
52” Wet Location
Ceiling Fan Owner’s Manual
RIPTIDE
CF605BQ00
Barbeque Black
CF605GRT00
Graphite
Model Numbers
Net Weight: 19.4 Lbs.
CF605ORB00
Oil Rubbed Bronze
CF605SW00
Satin White
• Español - página 37
• Français - page 73
READ AND SAVE THESE INSTRUCTIONS
INDOOR/OUTDOOR
1-800-777-4440
Questions, problems, missing parts: Before returning to the store, Call Customer Service
www.luminancebrands.com
Table of Contents
2
U.L. Model No.: CF605
Section Page
Safety Instructions ................................ 2
1. Unpacking Instructions ..........................3-4
2. Electrical Requirements .......................... 4
3. Ceiling Fan Assembly ..........................5-14
4. How to Hang Your Ceiling Fan ..................15-16
5. How to Wire Your Ceiling Fan ..................17-21
6. Final Assembly ................................ 22
7. Remote Control Procedures ....................23-25
8. Reverse Switch Operation........................ 26
9. Installation of No-Light Cover (Sold Separately) .....27-29
Section Page
10. Maintenance ................................. 30
11. Accessories ................................. 30
12. Remote Control Troubleshooting ................. 30
13. Troubleshooting .............................. 31
14. Repair Parts ...............................32-33
15. Energy Efficient Use of Ceiling Fan ............... 34
Ceiling Fan Limited Warranty ....................... 35
Spanish ........................................ 37
French ........................................ 73
READ AND SAVE THESE INSTRUCTIONS
Safety Instructions
TO REDUCE THE RISK OF FIRE, ELECTRICAL
SHOCK, OR INJURY TO PERSONS, OBSERVE THE
FOLLOWING:
a. Use this unit only in a manner intended by the
manufacturer. If you have questions, contact the
manufacturer.
b. Before servicing or cleaning unit, switch power
off at service panel and lock service panel
disconnecting means to prevent power from
being switched on accidentally. When the service
disconnecting means cannot be locked, securely
fasten a warning device, such as a tag, to the
service panel.
WARNING
!
Additional Safety Instructions for Installation
1. To avoid possible shock, be sure electricity is turned
off at the main fuse box or circuit breaker panel before
wiring, and do not operate fan without blades.
2. All wiring must be in accordance with the National
Electrical Code “ANSI/NFPA 70-2017” and Local
Electrical Codes. Use the National Electrical Code
if Local Codes do not exist. The ceiling fan must be
grounded as a precaution against possible electrical
shock. Electrical installation should be made or
approved by a licensed electrician.
3. The outlet box and joist must be securely mounted
and capable of reliably supporting at least 50 pounds.
Use only U.L. outlet boxes listed as “Acceptable for
Fan Support of 22.7 kg. (50 lbs.) or less”, and use
the mounting screws provided with the outlet box.
Most outlet boxes commonly used for support of light
fixtures are not acceptable for fan support and may
need to be replaced. Consult a qualified electrician if
in doubt.
4. Follow the recommended instructions for the proper
method of wiring your ceiling fan. If you do not know
enough about electrical wiring, have your fan installed
by a licensed electrician.
NOTE: This fan is suitable for use with solid-state speed
controls.
NOTE: All set screws must be checked and re-tightened
where necessary before installation.
1. Read your owner’s manual carefully and keep it for
future reference.
2. Be careful of the fan and blades when cleaning,
painting, or working near the fan. Always turn off the
power to the ceiling fan before servicing.
3. Do not put anything into the fan blades while they are
turning.
4. Do not operate reversing switch until fan blades have
come to a complete stop.
To reduce the risk of electrical shock, this fan must be
installed with an isolating wall control/switch.
To reduce the risk of fire or electrical shock, this fan
should only be used with fan speed control, Model No.
UC7067RAI, manufactured by Rhine Electric Co., Ltd.
To avoid fire, shock or injury, do not use a Luminance
Brands or any other brand of control not specifically
approved for this fan.
This product is designed to use only those parts
supplied with this product and/or any accessories
designated specifically for use with this product
by Luminance Brands. Substitution of parts or
accessories not designated for use with this product
by Luminance Brands could result in personal injury or
property damage.
To reduce the risk of personal injury, do not bend
the blade flange when installing the blade flanges,
balancing the blades or cleaning the fan. Do not insert
foreign objects in between rotating fan blades.
WARNING
!
To reduce the risk of injury, install the fan so that the
blades are at least 7 ft. (2.1m) above the floor.
CAUTION
!
1. Unpacking Instructions
3
luminancebrands.com
Please contact 1-800-777-4440 for further assistance
U.L. Model No.: CF605
This product is designed to use only those parts
supplied with this product and/or any accessories
designated specifically for use with this product
by Luminance Brands. Substitution of parts or
accessories not designated for use with this product
by Luminance Brands could result in personal injury
or property damage.
WARNING
!
Do not install or use fan if any part is damaged or
missing. Call Toll-Free:
1-800-777-4440
WARNING
!
1.1
Open Carton containing the Fan. Remove top half of
styrofoam unit. Remove Parts and check to see that
you have received the following Hardware and Parts:
NOTE: If you are uncertain of part description, refer
to exploded view illustration.
NOTE: Place the parts from the loose parts bags
in a small container to keep them from being lost.
If any parts are missing, contact your local retailer
or catalog outlet for replacement before proceeding.
E
A
F
D
G
K
H
I
J
B
C
PACKAGE CONTENTS
HARDWARE CONTENTS
Part Description Quantity
1 Wire Connectors, 12 ga. 3
2 Clevis Pin 1
3 Hairpin Clip 1
4 Threaded Stud, #8-32 x 1-1/4” 2
5 Knurled Knobs, #8-32 2
6 Lockwashers, External Tooth #8 2
7 #10-24 x 10 mm Flat Head Screws 10
8 #8-32 x 10 mm Serrated Pan Head Screw (spare) 1
9 Blade Balance Kit 1
Part Description Quantity
A Fan Motor Assembly 1
B Ceiling Cover 1
C Upper Housing 1
D Light Kit Adapter 1
E Blades 3
F LED Light Fixture Assembly 1
G Shade 1
H Hanger Bracket 1
I Hanger Ball / 8” Downrod Assembly 1
J Remote Control Receiver and Hardware 1
K Remote Control Transmitter, SR401
with Wall Bracket and Hardware 1
7
4
8
9
3
2
6
5
1
4
U.L. Model No.: CF605
1. Unpacking Instructions (Continued)
2. Electrical Requirements
To reduce the risk of fire, electric shock, or personal
injury, mount fan to outlet box marked “Acceptable
for Fan Support of 22.7 kg. (50 lbs.) or less”, and
use screws supplied with outlet box. Most outlet
boxes commonly used for support of light fixtures
are not acceptable for fan support and may need to be
replaced. Consult a qualified electrician if in doubt.
WARNING
!
Turning off wall switch is not sufficient. To avoid
possible electrical shock, be sure electricity is turned
off at the main fuse box or circuit breaker panel before
wiring. All wiring must be in accordance with National
and Local codes and the ceiling fan must be properly
grounded as a precaution against possible electrical
shock.
WARNING
!
To avoid fire or shock, follow all wiring instructions
carefully.
Any electrical work not described in these
instructions should be done or approved by a licensed
electrician.
WARNING
!
Your new Ceiling Fan will require a Grounded Electrical
Supply Line of 120 Volts AC, 60 Hz, 15 Amp Circuit.
The Outlet Box MUST be securely Anchored and
capable of withstanding a Load of at least 50 Pounds.
IMPORTANT: Your ceiling fan will not function
properly, and may be damaged, if used with any
wall dimmer switch or control other than the
Luminance Brands Electric Fan/Light Remote
Control supplied with the fan.
If your Fan is to replace an Existing Ceiling Light
Fixture, turn Electricity OFF at the Main Fuse Box
or Circuit Breaker Panel at this time and remove the
existing Light Fixture.
Please call Customer Service at 1-800-777-4440
if you have any questions about installation and
operation of this Ceiling Fan.
Tools Needed for Assembly
One Phillips Head Screwdriver One Stepladder
One Wire Stripper One Wire Cutter
Materials
Wiring outlet box and box connectors must be of type
required by the local code. The minimum wire would be
a 3-conductor (2-wire with ground) of following size:
Installed Wire Length Wire Size A.W.G.
Up to 50 ft. 14
50-100 ft. 12
Your Luminance Brands Ceiling Fan comes supplied
with a Fan/Light Remote Control which consists of
a Receiver mounted inside the Ceiling Cover.
This system allows you to regulate your Ceiling Fan
Speed and Light ON/OFF.
Before assembling your ceiling fan, refer to section
on proper method of wiring your fan (page 17).
If you feel you do not have enough wiring knowledge
or experience, have your fan installed by a licensed
electrician.
WARNING
!
THIS FAN MODEL IS SUITABLE FOR WET LOCATIONS
SUCH AS PORCHES, PATIOS, AND DECKS.
This Manual Is Designed to Make it as Easy as Possible for You to Assemble,
Install, Operate and Maintain Your Ceiling Fan
5
luminancebrands.com
Please contact 1-800-777-4440 for further assistance
U.L. Model No.: CF605
3. Ceiling Fan Assembly
STYROFOAM
FAN MOTOR
ASSEMBLY
Figure 1
3.1
Remove the Fan Motor Assembly from the protective
plastic bag.
Place the Fan Motor Assembly, Bottom side facing up,
onto both styrofoam forms from the carton (Figure 1).
The styrofoam forms serves as a holder for the Fan
during the first stages of assembly.
REMOVE ONE #8-32 x 10 mm
SERRATED PAN HEAD SCREW
FAN MOTOR
ASSEMBLY
LOOSEN TWO #8-32 x 10 mm
SERRATED PAN HEAD SCREWS
Figure 2
3.2
Remove and Retain One of the Three #8-32 x 10mm
Serrated Pan Head Screws from the Fan Motor
Assembly.
Loosen the remaining Two #8-32 x 10 mm Serrated
Pan Head Screws (Figure 2).
3. Ceiling Fan Assembly (Continued)
6
U.L. Model No.: CF605
LIGHT KIT
ADAPTER
TURN LOWER ADAPTER
CLOCKWISE
ENGAGE TWO #8-32 x 10 mm
SERRATED PAN HEAD SCREWS
MOTOR
COUPLER
Figure 3
REINSTALL ONE #8-32 x 10 mm
SERRATED PAN HEAD SCREW
LIGHT KIT
ADAPTER
RETIGHTEN TWO #8-32 x 10 mm
SERRATED PAN HEAD SCREWS
3.4
Reinstall the previously removed #8-32 x 10 mm
Serrated Pan Head Screw into the Light Kit Adapter
(Figure 4).
Secure the Light Kit Adapter by tightening the Three
#8-32 x 10 mm Serrated Pan Head Screws (Figure 4).
A spare #8-32 x 10 mm Serrated Head Pan Screw
supplied in parts bag, if needed.
Figure 4
3.3
Place the Wires and Connectors through the Center
Hole of the Light Kit Adapter.
Position the Light Kit Adapter onto the Fan Motor
Assembly Loosened Screws.
NOTE: For Ease of Light Kit Adapter Installation:
Hold the Motor Coupler, located at the underside of
the Fan Motor Assembly while installing the Light
Kit Adapter.
Rotate the Light Kit Adapter Clockwise to Engage the
Two loosened #8-32 x 10 mm Serrated Pan Head
Screws in the Two Key Slots (Figure 3).
7
luminancebrands.com
Please contact 1-800-777-4440 for further assistance
U.L. Model No.: CF605
3. Ceiling Fan Assembly (Continued)
FAN MOTOR
ASSEMBLY
WHITE WIRE
LED LIGHT FIXTURE
ASSEMBLY
LED LIGHT FIXTURE
ASSEMBLY BLACK
WIRE
LED LIGHT FIXTURE
ASSEMBLY WHITE
WIRE
FAN MOTOR
ASSEMBLY
BLUE WIRE
Figure 5
3.5
Securely connect the LED Light Fixture Assembly
White Wire Terminal to the Fan Motor Assembly White
Wire Terminal (Figure 5).
Securely connect the LED Light Fixture Assembly Black
Wire Terminal to the Fan Motor Assembly Blue Wire
Terminal (Figure 5).
To reduce the risk of electric shock, disconnect the
electrical supply circuit to the fan before installing
light fixture.
CAUTION
!
NOTE: If Installing the Ceiling Fan without the LED Light Fixture Assembly,
Skip Sections 3.5 - 3.8 and Complete 3.9 - 3.18.
Section 9, Installation of No-Light Cover (Sold Separately) will replace the LED Shade.
REMOVE ONE #8-32 x 10 mm
SERRATED PAN HEAD SCREW
LIGHT KIT
ADAPTER
LOOSEN TWO #8-32 x 10 mm
SERRATED PAN HEAD SCREWS
Figure 6
3.6
Remove and Retain One of the Three #8-32 x 10 mm
Serrated Pan Head Screws from the Light Kit Adapter.
Loosen the remaining Two #8-32 x 10 mm Serrated
Pan Head Screws (Figure 6).
3. Ceiling Fan Assembly (Continued)
8
U.L. Model No.: CF605
REINSTALL ONE #8-32 x 10 mm
SERRATED PAN HEAD SCREW
MOTOR
COUPLER
RETIGHTEN TWO #8-32 x 10 mm
SERRATED PAN HEAD SCREWS
LED LIGHT FIXTURE
ASSEMBLY
TURN LED
CLOCKWISE
Figure 7
3.7
Tuck wires into the LED Light Fixture Assembly and
position on the Light Kit Adapter Assembly.
NOTE: For Ease of LED Light Fixture Assembly
Installation: Hold the Motor Coupler, located at
the underside of the Fan Motor Assembly while
installing the LED Light Fixture Assembly.
Rotate the LED Light Fixture Assembly Clockwise to
Engage the Two loosened #8-32 x 10 mm Serrated
Pan Head Screws in the Two Key Slots (Figure 7).
Reinstall the One previously removed #8-32 x 10 mm
Serrated Pan Head Screw (Figure 7).
Secure the LED Light Fixture Assembly by tightening
the Three #8-32 x 10 mm Serrated Pan Head Screws
(Figure 7).
A spare #8-32 x 10 mm Pan Head Screw is supplied in
parts bag, if needed.
To avoid possible fire or shock, do not pinch wires
between the light kit adapter and the LED light fixture
assembly.
WARNING
!
9
luminancebrands.com
Please contact 1-800-777-4440 for further assistance
U.L. Model No.: CF605
3. Ceiling Fan Assembly (Continued)
3.8
NOTE: For Ease of Shade Installation: Hold the
Motor Coupler, located at the underside of the Fan
Motor Assembly while installing the Shade.
Place the Shade into the opening in the Light Kit
Adapter, aligning the Three Flat Areas on the top edge
of the Shade with the Light Kit Adapter Three Raised
Dimples.
Turn the Shade Clockwise until it stops (Figure 8).
NOTE: Periodically check that the Shade is seated
fully clockwise in the Light Kit Adapter.
Carefully turn the partially assembled Ceiling Fan right
side up and place the Fan securely into the packing
styrofoam.
MOTOR
COUPLER
TURN SHADE CLOCKWISE
LIGHT KIT ADAPTER
RAISED DIMPLES (3)
SHADE FLAT
AREAS (3)
SHADE
Figure 8
10
3. Ceiling Fan Assembly (Continued)
PHILLIPS HEAD SET SCREW (LOOSENED)
HANGER BALL
DOWNROD
PIN
GREEN GROUND WIRE
Figure 9
3.9
Remove the Hanger Ball by loosening the Phillips Head
Set Screw in the Hanger Ball until the Ball falls freely
down the 8” Downrod (Figure 9).
Remove the Pin from the Downrod, then remove the
Hanger Ball (Figure 9).
Retain the Pin and Hanger Ball for reinstallation in
Step 3.16.
NOTE: Do not loosen the Screw that attaches the
Green Ground Wire to the Hanger Ball.
DOWNROD
THREE 80" MOTOR
WIRES (UNTWISTED)
Figure 10
3.10
Separate, untwist and unkink the Three 80” Motor
Wires.
Route the Three 80” Black, Blue, and White Motor
Wires through the 8” Downrod (Figure 10).
U.L. Model No.: CF605
Questo manuale è adatto per i seguenti modelli
3
Indice
Lingue:
Altri manuali Luminance Brands Fan
Luminance Brands
Luminance Brands HF1161BQ00 Manuale utente
Luminance Brands
Luminance Brands kathy ireland ARLO INDOOR Manuale utente
Luminance Brands
Luminance Brands kathy ireland HOME VERANDA Manuale utente
Luminance Brands
Luminance Brands kathy ireland home Manuale utente
Luminance Brands
Luminance Brands kathy ireland HOME GEODE Manuale utente
Luminance Brands
Luminance Brands kathy ireland ASTOR CF235BQ00 Manuale utente
Luminance Brands
Luminance Brands kathy ireland HOME MIDWAY ECO LED CF955LBS00 Manuale utente
Luminance Brands
Luminance Brands Kathy Ireland Home TILO CF130BS00 Manuale utente
Luminance Brands
Luminance Brands kathy ireland HOME Tilo LK130 Manuale utente
Luminance Brands
Luminance Brands Kathy Ireland Home Prima Snugger CF905BS01 Manuale utente
Luminance Brands
Luminance Brands kathy ireland HOME CARRERA CF784BS03 Manuale utente
Luminance Brands
Luminance Brands kathy ireland ASHLAND CF717AP02 Manuale utente
Luminance Brands
Luminance Brands Kathy Ireland Home Highpointe LED CF205LBQ01 Manuale utente
Luminance Brands
Luminance Brands Kathy Ireland Home Summer Night CF742PFORB01 Manuale utente
Luminance Brands
Luminance Brands Kathy Ireland Home CF766LBQ00 Manuale utente
Luminance Brands
Luminance Brands Kathy Ireland Home FLORET ECO Manuale utente
Luminance Brands
Luminance Brands kathy ireland HOME Wet Location SEA BREEZE Manuale utente
Luminance Brands
Luminance Brands kathy ireland HOME CURVA SKY LED INDOOR Manuale utente
Luminance Brands
Luminance Brands kathy ireland HOME EUCLID Manuale utente
Luminance Brands
Luminance Brands kathy ireland HOME Summerhaven LED... Manuale utente
Luminance Brands
Luminance Brands VOLTA CF590RBQ00 Manuale utente
Luminance Brands
Luminance Brands kathy ireland HOME Batalie Breeze CF621VNB00 Manuale utente
Luminance Brands
Luminance Brands kathy ireland home CF835AP00 Manuale utente
Luminance Brands
Luminance Brands Kathy Ireland Home BELLA CF442ORB00 Manuale utente
