Warranty
For warranty information, please visit:
www.lutron.com/DriverWarranty
)Lutron, Lutron, Ariadni, Diva, GRAFIK Eye, Hi-lume, HomeWorks,
Maestro, Maestro Wireless, Nova, Nova T*, PowPak, Quantum,
RadioRA, EcoSystem, and Skylark are trademarks of Lutron
Electronics Co., Inc. registered in the U.S. and other countries.
Energi Savr Node and Soft-on, Fade-to-Black are trademarks of
Lutron Electronics Co., Inc.
©2015– 2017 Lutron Electronics Co., Inc.
L3D0-96W24V-U Troubleshooting
Problem Possible Solution
LED does not illuminate
at high-end • Verify that the system is wired correctly according to wiring diagram and
powered.
•
Verify that the LED load is wired correctly; +LED to positive, -LED to negative.
• Verify that the LED load is for “constant-voltage” applications with PWM
dimming.
• Verify that the LED load is compatible with the specified voltage output
of the driver.
• Lutron drivers are not for use with MR16 LED lamps.
LED does not illuminate
at low-end • Verify that the low-end trim on the control is set properly.
• Turn Field Adjustment Knob clockwise until desired low-end operation is
obtained.
LED does not dim • Verify that Switched Hot and Dimmed Hot are connected to the proper
terminals for 3-wire control.
• Verify EcoSystem control wiring (E1 and E2) is wired according to the
instructions for digital control.
LED turns on/off
abruptly without Soft-on,
Fade-to-Black feature
• Turn Field Adjustment Knob counter-clockwise until desired low-end
operation is obtained.
• 3-wire control does not have Soft-on, Fade-to-Black dimming
technology.
LED is flashing,
flickering, dropping out,
or has poor dimming
performance
• Verify that a compatible dimmer is being used to control the driver.
• Verify that the input voltage is within the rated limits.
• Verify that Switched Hot and Dimmed Hot are connected to the proper
terminals.
• Verify that the LED load is for “constant-voltage” with PWM dimming
applications.
• Verify that the length of wires between driver and LED does not exceed
specification.
• Verify that the rated voltage is present at the driver.
• Certain types of LED loads may be incompatible.* Verify that the LED
load is within the specified wattage range of 2 W to 96 W.
• Lutron drivers are not for use with MR16 LED lamps.
LED is flashing slowly
(6to 8 second interval) • Verify that the LED load does not exceed the maximum specified power
rating of the driver (96 W).
• Verify that the LED load matches the specified voltage output of the driver.
• Verify that the length of wire between driver and LED does not exceed
specification.
• Certain types of LED loads may be incompatible.
*
LED output appears
dim at high-end • Verify that rated line voltage is present at the terminal.
• Verify that the driver is operating in an environment within its ambient
temperature rating.
• Verify that the driver is not located adjacent to other heat producing
devices. Verify that space between drivers is greater than 3 in (76 mm).
• Verify that the maximum lead length is not exceeded per Lutron
recommendation.
• Verify that the LED load is installed per manufacturer’s instructions.
• Verify that the LED load is compatible with the specified voltage output
of the driver.
Not all LED strips/
fixtures illuminate • Verify that multiple LEDs connected to a single driver are properly wired.
• Verify that the LED load is installed per manufacturer’s instructions.
Not all LEDs on the
same strip are evenly lit • Verify that the length of wire between the driver and LED does not
exceed specifications.
• Verify that the LED load is for “constant-voltage” with PWM dimming
applications.
• Verify that the LED load is installed per manufacturer’s instructions.
LED is brighter/hotter
than expected • Verify that the LED load is compatible with the specified voltage output
of the driver.
* Certain constant-voltage loads may have added capacitance. Contact the Lutron LED Center of Excellence at 1.877.346.5338 or
LEDs@lutron.com for more information about these loads.
Hi-lume Premier 0.1% EcoSystem/3-wire Voltage LED Driver
Compatible Controls
Compatible Controls
• 3-Wire Controls
• EcoSystem Controls
Consult individual component installation
guides for more details.
Driver Leads
Maximum wire length between LED driver and
start of the light engine:
Wire Gauge* Maximum Lead Length
24 AWG (0.20 mm2)* 6 ft (1.8 m)
22 AWG (0.75 mm2)* 10 ft (3.0 m)
20 AWG (0.50 mm2) 15 ft (4.5 m)
18 AWG (0.75 mm2) 25 ft (7.62 m)
16 AWG (1.0 mm2) 40 ft (12.2 m)
14 AWG (1.5 mm2) 60 ft (18.3 m)
12 AWG (2.5 mm2) 100 ft (30.5 m)
10 AWG (4.0 mm2)* 150 ft (45.7 m)
* To use wire gauges larger or smaller than terminal
blocks’ rated gauge of 20 AWG to 12 AWG (0.50 mm2
to 2.50 mm2), connect 12 in (30 cm) or less of rated
wire from terminal and connect with larger or smaller
wire.
Field Adjustment Knob
Adjusting knob on the outside of the
enclosure changes the minimum
light level that is reached during
normal operation. This feature
enables the user to address light
output mismatch between two or
more drivers at low-end dim level.
Driver is initially defaulted to the
minimum light output when at
low-end. For more information,
please refer to Application Note
#591 (P/N 048591) at www.lutron.
com
1. Ensure knobs on all drivers are in the full
counter-clockwise position.
2. Set control to get lowest light level.
3. Turn knob clockwise to adjust light output to
match the brightest driver.
4. Repeat steps 2-3 for the remaining drivers.
Compatible Controls
For assistance in selecting controls, contact our LED Center of Excellence.
3-Wire Controls (without Soft-on, Fade-to-Black dimming technology)
Product Model Number Drivers per Control** Load Selection
Type
Low-end
trim setting†
120 V~277 V~120 V~277 V~
Nova T*NTF-10- NTF-10-277- 1 – 16 1 – 19 — —
NTF-103P- NTF-103P-277- 1 – 8 1 – 14 — —
Nova NF-10- NF-10-277- 1 – 16 1 – 19 — —
NF-103P- NF-103P-277- 1 – 8 1 – 14 — —
Skylark SF-10P- SF-12P-277- 1 – 8 1 – 14 — —
SF-103P- SF-12P-277-3- 1 – 8 1 – 14 — —
Diva DVF-103P- DVF-103P-277- 1 – 8 1 – 14 — —
DVSCF-103P- DVSCF-103P-277- 1 – 8 1 – 14 — —
Ariadni AYF-103P- AYF-103P-277- 1 – 8 1 – 14 — —
Maestro MAF-6AM- MAF-6AM-277- 1 – 6 1 – 14 — —
MSCF-6AM- MSCF-6AM-277- 1 – 6 1 – 14 — —
Maestro Wireless MRF2-F6AN-DV- 1 – 6 1 – 14 — —
RadioRA 2 RRD-F6AN-DV- 1 – 6 1 – 14 Dual voltage 3-wire
dimmer 21%†
HomeWorks QS HQRD-F6AN-DV- 1 – 6 1 – 14 Fluorescent 3-wire
LED 3-wire 21%†
Interface
PHPM-3F-120- — 1 – 16 — — —
PHPM-3F-DV- 1 – 16 1 – 38 — —
BCI-0-10 1 – 16 1 – 38 — —
GP Dimming Panel Various 1 – 16 1 – 38 2 – 1 —
EcoSystem Controls (with Soft-on, Fade-to-Black dimming technology)
Product Model Number Recommended
System Versionr
Drivers per Control
120 – 277 V~120 V~277 V~
PowPak Dimming Module
with EcoSystem RMJ-ECO32-DV-B,
URMJ-ECO32-DVB 5.9 or higher 32 per EcoSystem link
PowPak Wireless Fixture
Control with EcoSystem
‡FCJ-ECO
FCJS-ECO 0796554 or higher 3 per EcoSystem link
Energi Savr Node with
EcoSystem
QSN-1ECO-S, QSN-2ECO-S,
QSN-2ECO-PS120,
UQSN-1ECO-S, UQSN-2ECO-S 9.027 or higher 64 per EcoSystem link
GRAFIK Eye QS with
EcoSystem QSGRJ-_E,
QSGR-_E — 9.009 or higher 64 per EcoSystem link
Quantum Light
Management Hub QP2-_P_C — 3.2 or higher
§64 per EcoSystem link
HomeWorks QS with
EcoSystem
LQSE-2ECO-D,
QSGRJ-_E,
QSGR-_E, — 10 or higher* 64 per EcoSystem link
NOTE: For information about Legacy product use in existing control applications, contact LEDs@lutron.com
** No derating required in multigang applications provided that the driver count does not exceed the quantity listed.
†21% trim allows for 0.1% low-end level but might result in dead travel for 1% – 4% on user interface. 22% trim can be used to avoid dead travel but
may result in >0.1% low-end level.
‡All devices connected to one PowPak wireless fixture controller will be controlled together. Devices will dim to the same level as the result of a
control command. Control will need to have low-end level reprogrammed to dim to 0.1% output. For more details, refer to Application Note #556 at
www.lutron.com.
§Version 3.1 (or higher) is required to dim lower than 1%.
* Version 7.0 (or higher) is required to dim lower than 1%.
rFor lower system versions, please visit www.lutron.com/LEDsystemcheck to check if your system requires changes.
