Luxrite LR25140 Manuale utente

WARNING

！

RIS9451

1/3

PACKAGING CONTENTS

MODEL# LR25140

LR25141

LR25142

LR25143

LR25144

LR25145

LR25146

LR25147

LR25148

A. Fixture channel

C. Channel cover with LED’s

B. Decorative end caps

D. Lens assembly

(Purchase separately)

ITEMS REQUIRED

Note:This product is intended for either single mount or continuous row applications.

Stud mount (2) 1 1/2in. long #8 or larger wood screws and a #10 flat washer

Drywall mount (2) 3in. long 3/16” or larger diameter toggle bolt and #10 flat washer

(if joist cannot be located)

Phillips screwdriver

Flat head screwdriver

Pliers

Hammer

Safety glasses

Ladder

When using product, basic precautions should always be followed, inchuding the following:

IMPORTANT SAFETY INSTRUCTIONS

Read and follow these instructions.

Heed all warnings,including below warnings AND those included on product.

Save these instructions and warnings.

Risk of fire/electric shock.

Ground fixture to avoid potential electric shock.

Turn off the power at fuse or circuit breaker box before installation and maintenance.

Edges may cut. Handle with care.

The fixture is connected to 120-277 volt, 50Hz or 60Hz power source.

Fixture should be installed by persons with experience wiring or by a qualified electrician. The electrical system, and the method of

electrically connecting the fixture to it, must be in accordance with the National Electrical Code and local building codes.

CAUTION

LED STRIP LIGHT INSTALLATION INSTRUCTION

2/3

Fig. 1

RIS9451

Fig. 2

1. Turn off the power at the main

fuse/breaker box.Carefully open carton,

remove fixture and end caps from carton.

2. To remove the channel cover with LED’s

from the main channel body squeeze

beneath the embossed locking tabs on

the main channel body and lift on the

channel cove with LED’s. Do this for all 6

locking tab locations (Fig.1.). The channel

cover with LED’s can be placed in safe

location until fixture is mounte.

3. Remove appropriate knockout(s) for

power supply wiring. To remove, simply

place a flathead screwdriver on the

knockout and strike it sharply with a

hammer (Fig.2.) The slug may then be

removed with pliers.

Fig. 3

Fig. 4

4. Connect L/N wire using supplied wire

nut(Fig.3.)

5. Prepare the supply wires.

A. Wiring must comply with all applicable

electrical codes.

B. Strip wire to 3/8”(9.5mm).(Fig.3.)

6. Attach junction box cover plate and pull

wire through junction box(Fig.4.)

Note:See row mounting section if

row mounting before continuing

to step 7.

Fig. 8Fig. 7

Fig. 5

7. Locate power supply wires from the junction box and pull them through

the knockout that has been removed on the main channel body so that

the wires and disconnect are inside the housing channel(Fig.5).

8. Attach main housing channel to ceiling or wall using #8 or larger diameter

wood screws plus #10 flat washer for stud mount or 3/16” diameter or

larger toggle bolt plus #10 flat washer for drywall mounting. The spacing

for mounting brackets is 37-3/16” for 4’ fixture or 14 9/16” for

2’ fixture.(Fig.6&7).

Note: 2’ fixture mounting hole pattern is not symmetric.

Fig. 6

9. Connect junction box and driver using supplied wire nut.Black to

black and white to white.(Fig.8).

Fig. 9A Fig. 9B

10. Locate the channel cover with LEDs and provided lead wires to make

connections to the driver output wires and ground wire. To properly

engage wires, fimly push wire leads into the orange in-line connector

attached to the driver output leads. Connect the black lead on the cover

with the black lead on the driver. Then, connect the red lead on the

cover with the red lead on the driver. Lastly, connect the green lead

on the cover with the green ground lead on the housing channel.

For fixtures with 2 drivers connect the second set of black and

red wires to the Channel cover with LED’s. Black to black and red to red

(Fig. 9A, 9B & 9C).

Note: For dimming see Installing Dimmer Instruction Section.

Fig. 9C

Fig. 10

11. Tuck all the excess supply wire, orange inline connectors, and the quick

disconnect back into the main channel housing.

12. Mechanically attach the Channel cover with LED’s back to the housing

channel by sliding the Channel cover with LED’s holes onto the locking

tabs on the main housing channel(Fig. 10) ,Remove protective film from

the lens.

13. Optional: Attach decorative end caps by placing the end cap’s locking

tabs over the ends of the fixture and sliding towards the center of the

fixture until both the locking tabs snap into end cap holes on main

housing (Fig. 11A & 11B).

Note: Decorative end caps cannot be placed between two

fixtures which have been row mounted together.

For row mounting decorative end caps can only be

placed on far ends of fixture.

INSTALLATION INSTRUCTIONS

LLNN

3/3

Fig.14A

Fig. 12

Fig. 14B Fig. 14C

Fig. 13

Fig. 11B

Fig. 11A

1. For row mounting locate the metal end plate at the end of the fixture of

the main channel body which you plan to remove. Remove the endplate

screw from the metal endplate(Fig.12).Repeat for adjacent fixture.

ROW MOUNTING

2. Squeeze the main channel housing to release the locking tabs on the

metal end plate and remove the metal end plate from main channel

housing(Fig.13). Repeat for adjacent fIxture.

3. Using one of the metal end plates which you just removed break away

the row mounting tab by bending the end plate. A few maximum bens

may be required to completely break away the tab (Fig. 14A).

4. Using the mounting tab from the metal end plate insert it into the slots

provided at the end of the main channel housing (Fig.14B). Ensure locking

tabs are facing thelocking tab hole provided in the main housing body.

Slide row mounting tab into slot until an audible click is heard (Fig.14C).

5. Mount the first fixture with row mounting tab following steps 7-12 above.

6. To install second fixture side fixture over row mounting tab (Fig. 14C) and

follow steps7-12 above.

RIS9451

Allstar Lighting Supplies Inc. 33 Randolph Ave. Avenel NJ 07001

Tel: 732-882-1500

This LUXRITE Fixture, when properly installed and under normal

conditions of use, are warranted to be free from defects in materials for

three years from date of sale.

Questo manuale è adatto per i seguenti modelli

Altri manuali Luxrite Apparecchio di illuminazione

Luxrite

Luxrite LR34129 Manuale utente

Manuali Apparecchio di illuminazione popolari di altre marche

Emos

Emos CLASSIC ZY1431T Manuale utente

Westinghouse

Westinghouse Outdoor Lighting Fixture Manuale utente

Hedler

Hedler C 12 silent Manuale utente

Blizzard Lighting

Blizzard Lighting Puck: CSI Manuale utente

Energetic Lighting

Energetic Lighting ELYSL-5004 Series Manuale utente

Lightmaxx

Lightmaxx Shaft 5R Manuale utente

Triarch

Triarch 31083 Manuale utente

Philips

Philips 32614 Series Manuale utente

IKEA

IKEA TIVED Manuale utente

Lightolier

Lightolier LP200 Manuale utente

Chauvet Professional

Chauvet Professional ROGUE R1 BEAM WASH Manuale utente

Martin

Martin MAC 250 Krypton Manuale utente

Cooper Lighting

Cooper Lighting Halo L3232E Manuale utente

Stageline

Stageline ODW-2410RGBW Manuale utente

Light Sky

Light Sky Tornado Series Manuale utente

Lightolier

Lightolier Paralyte 2424 PLA2G9LS26U Manuale utente

Lightolier

Lightolier Lytespan 83ED17S Manuale utente

Lightolier

Lightolier Calculite CS8226 Manuale utente