M-system 6BSN Manuale utente

BEFORE USE ....

Thank you for choosing M-System. Before use, please check

contents of the package you received as outlined below.

If you have any problems or questions with the product,

please contact M-System’s Sales Ofﬁce or representatives.

■PACKAGE INCLUDES:

Transmitter module............................................................(1)

Outdoor enclosure ...............................................................(1)

Mounting screws

Bolt (M8 × 15)....................................................................(4)

Spring washer for M8 .......................................................(4)

Mounting bracket assembly (optional)

Mounting bracket..............................................................(1)

M10 U-bolt.........................................................................(2)

Nut for M10 .......................................................................(4)

Spring washer for M10 .....................................................(4)

■MODEL NO.

Conﬁrm Model No. marking on the product to be exactly

what you ordered.

■INSTRUCTION MANUAL

This manual describes necessary points of caution when

you use this product, including installation, connection and

basic maintenance procedures.

POINTS OF CAUTION

■GENERAL PRECAUTION

• Before you remove the unit or mount it, turn off the input

signal for safety.

■ENVIRONMENT

• Do not install the unit where it is subjected to continuous

vibration. Do not subject the unit to physical impact.

• Environmental temperature must be within -5 to +70°C

(23 to 158°F) in order to ensure adequate life span and

operation.

■WIRING

• Do not install cables close to noise sources (relay drive

cable, high frequency line, etc.).

• Do not bind these cables together with those in which

noises are present. Do not install them in the same duct.

■AND ....

• The unit is designed to function as soon as the input sig-

nal is supplied, however, a warm up for 10 minutes is re-

quired for satisfying complete performance described in

the data sheet.

INPUT LOOP POWERED ISOLATOR MODEL 6BSN

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-8869 Rev.1 P. 1 / 5

INSTRUCTION MANUAL

COMPONENT IDENTIFICATION

Case

Specifications

Transmitter Module

Gasket

Cover

Internal Earthing Screw

External Earthing Screw

Spring Clip(s)

Knurled Knob(s)

Cable Entry Conduit

•Case Details

6BSN

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-8869 Rev.1 P. 2 / 5

EXTERNAL DIMENSIONS unit: mm (inch)

4–M8, 12 deep

92 (3.62)

110 (4.33)

70 (2.76)

118 (4.65)

7 (.28)

max.

39 (1.54)

19 (.75)

92 (3.62)

104 (4.09)

(.55)

(1.02)

MOUNTING BRACKET

(optional)

110 (4.33) dia.

19 (.75)

2–G 1/2, 1/2NPT, M20x1.5 or PG13.5

174 (6.85)

114 (4.49)

110 (4.33)

SPACE REQUIRED TO REMOVE COVER

6BSN

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-8869 Rev.1 P. 3 / 5

INSTALLATION

■MOUNTING THE ENCLOSURE ON A PIPE ■MOUNTING THE ENCLOSURE ON A WALL

TERMINAL CONNECTIONS

Connect the unit as in the diagram below.

−

INPUT OUTPUT

−

6BSN

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-8869 Rev.1 P. 4 / 5

WIRING INSTRUCTIONS

■SCREW TERMINAL

Torque: 0.6 N·m

CHECKING

Open the unit’s outdoor enclosure cover when you conduct

checking of the transmitter. Be sure to close the cover after

the checking is complete.

1) Terminal wiring: Check that all cables are correctly con-

nected according to the connection diagram.

2) Input: Check current with an ammeter. Be sure that the

connected transmitter allows the load shown in the fol-

lowing table.

MODEL EQUIVALENT INPUT IMPEDANCE

6BSN-A 230Ω plus output load

6BSN-H 90Ω plus output load × 0.16

3) Output: Check that output load is within the permissible

limit shown in the following table.

MODEL LOAD RESISTANCE

6BSN-A 50 – 350Ω

6BSN-H 50 – 600Ω

ADJUSTMENT PROCEDURE

This unit is calibrated at the factory to meet the ordered

speciﬁcations, therefore you usually do not need any cali-

bration.

For matching the signal to a receiving instrument or in case

of regular calibration, adjust the output as explained below.

Zero and Span adjustments are located behind the top cover

of the unit. Open the enclosure cover, release the knurled

knobs at the front of the unit and open the top cover.

After the calibration is complete, be sure to close both cov-

ers.

1234

VR1 VR2

■HOW TO CALIBRATE THE OUTPUT SIGNAL

Use a signal source and measuring instruments of sufﬁcient

accuracy level. Turn the input signal on and warm up for

more than 10 minutes.

1) ZERO: Apply 0% input and adjust output to 0% with the

VR1.

2) SPAN: Apply 100% input and adjust output to 100% with

the VR2.

3) Check ZERO adjustment again with 0% input.

4) When ZERO value is changed, repeat the above proce-

dure 1) – 3).

MAINTENANCE

Regular calibration procedure is explained below:

■CALIBRATION

Warm up the unit for at least 10 minutes. Apply 0%, 25%,

50%, 75% and 100% input signal. Check that the output

signal for the respective input signal remains within accu-

racy described in the data sheet. When the output is out of

tolerance, recalibrate the unit according to the “ADJUST-

MENT PROCEDURE” explained earlier.

LIGHTNING SURGE PROTECTION

M-System offers a series of lightning surge protector for

protection against induced lightning surges. Please contact

M-System to choose appropriate models.

6BSN

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-8869 Rev.1 P. 5 / 5

Indice

Altri manuali M-system Sistema I/O

M-system

M-system R3-SV8N Manuale utente

M-system

M-system R7M-DAC16C-R Manuale utente

M-system

M-system R3Y-SS16N Manuale utente

M-system

M-system R7D-YS2/UL Manuale utente

M-system

M-system R7M-TS4-R Manuale utente

M-system

M-system R3-RS4 Manuale utente

M-system

M-system R8 Series Manuale utente

M-system

M-system R3-SV8N Manuale utente

M-system

M-system R10M-CT4E Manuale utente

M-system

M-system R3-AS8 Manuale utente

M-system

M-system R7F4HML3-D-DAC32B Manuale utente

M-system

M-system R8-YVT4N Manuale utente

M-system

M-system R8-SS4N Manuale utente

M-system

M-system R7C-SV4 Manuale utente

M-system

M-system R30MS4 Manuale utente

M-system

M-system R3-SS8N Manuale utente

M-system

M-system R7F4DC-DC16A-H Manuale utente

M-system

M-system R3S-YV4 Manuale utente

M-system

M-system R7C-YV4 Manuale utente

M-system

M-system R7F4HEIP-DC16B Manuale utente

M-system

M-system Devicenet R7F4HD-DA32B Manuale utente

M-system

M-system R7ML-DC16A-R Manuale utente

M-system

M-system R7G4HEIP-6-DC16A Manuale utente

M-system

M-system R3-CT8C Manuale utente

Manuali Sistema I/O popolari di altre marche

WAGO

WAGO 750-344 Manuale utente

Teknim

Teknim TWM-1887 Manuale di istruzioni

Intelligent Appliance

Intelligent Appliance IA-2662-E Manuale utente

BERGHOF

BERGHOF ECC DIO 16/16 Manuale di istruzioni

Advantech

Advantech PCM-27J3AU Manuale di installazione e funzionamento

Festo

Festo CP-E08-M12-CL Manuale utente

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Manuale utente

Hitachi

Hitachi HX-RIO3 Series Manuale utente

NUUO

NUUO SCB-A08 Manuale utente

jablotron

jablotron JB-110N Manuale utente

Omron

Omron SYSMAC C200H Manuale utente

DOLD

DOLD SAFEMASTER M Manuale utente

ABB

ABB OPT-MF-001 Manuale utente

Omron

Omron SYSMAC C2000H Manuale utente

Helmholz

Helmholz TB20 Manuale utente

ICP DAS USA

ICP DAS USA tM-AD2 Manuale utente

Automationdirect.com

Automationdirect.com DL305 Manuale utente

WAGO

WAGO I/O-SYSTEM 750 Manuale utente