M-system JC-ECT Manuale utente
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp
EM-9043 P. 1 / 5
INSTRUCTION MANUAL
JUNCTION SLAVE
(EtherCAT) MODEL JC-ECT
BEFORE USE ....
Thank you for choosing M-System. Before use, please check
contents of the package you received as outlined below.
If you have any problems or questions with the product,
please contact M-System’s Sales Office or representatives.
■PACKAGE INCLUDES:
Junction slave......................................................................(1)
Mounter slider.....................................................................(1)
■MODEL NO.
Confirm Model No. marking on the product to be exactly
what you ordered.
■INSTRUCTION MANUAL
This manual describes necessary points of caution when
you use this product, including installation, connection and
basic maintenance procedures.
POINTS OF CAUTION
■CONFORMITY WITH EU DIRECTIVES
• The equipment must be mounted inside the instrument
panel of a metal enclosure.
• The actual installation environments such as panel con-
figurations, connected devices, and connected wires, may
affect the protection level of this unit when it is inte-
grated in a panel system. The user may have to review
the CE requirements in regard to the whole system and
employ additional protective measures to ensure the CE
conformity.
■POWER INPUT RATING & OPERATIONAL RANGE
• Locate the power input rating marked on the product and
confirm its operational range as indicated below:
24V DC rating: 24V ±10%
Power consumption:
JC-ECT-4: approx. 2.0 W, JC-ECT-8: approx. 4.3 W
■GENERAL PRECAUTIONS
• Before you remove the unit or mount it, turn off the power
supply and input signal for safety.
■ENVIRONMENT
• Indoor use
• When heavy dust or metal particles are present in the
air, install the unit inside proper housing with sufficient
ventilation.
• Do not install the unit where it is subjected to continuous
vibration. Do not subject the unit to physical impact.
• Environmental temperature must be within -10 to +55°C
(14 to 131°F) with relative humidity within 10 to 90% RH
in order to ensure adequate life span and operation.
■WIRING
• Do not install cables close to noise sources (relay drive
cable, high frequency line, etc.).
• Do not bind these cables together with those in which
noises are present. Do not install them in the same duct.
■AND ....
• The unit is designed to function as soon as power is sup-
plied, however, a warm up for 10 minutes is required for
satisfying complete performance described in the data
sheet.
JC-ECT
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp
EM-9043 P. 2 / 5
COMPONENT IDENTIFICATION
PWR+
PWR
-
FE
I N
X 2
L /A
X 3
X 4
L /A
L /A
L /A
PWR
RJ-45 Modular Jack
for EtherCAT
Power Supply
Connector
Status Indicator LED PWR LED
■ MODULE TYPE: 4 (4 ports)
PWR+
PWR
-
FE
L /A
L /A
X 5
X 6
L /A
L /A
X 7
X 8
I N
X 2
L /A
X 3
X 4
L /A
L /A
L /A
PWR
RJ-45 Modular Jack
for EtherCAT
Power Supply
Connector
Status Indicator LED PWR LED
■ MODULE TYPE: 8 (8 ports)
■STATUS INDICATOR LED
ID FUNCTION COLOR S TAT U S
PWR Main unit internal power Green OFF Error
ON Normal
L/A Port link / activity status Green
OFF No Link
Flickering Link and activity
ON Link without activity
Flickering 50ms-On, 50ms-Off
WIRING INSTRUCTIONS
1. PWR + Power Supply
2. PWR − Power Supply
3. FE Functional earth
1
2
3
Cable connector: TFMC1,5 / 5–STF–3,5
(Phoenix Contact) (included in the package)
Applicable wire size:
0.2 − 1.5 mm2;stripped length 10 mm
Recommended solderless terminal
• AI0,25−10YE 0.25 mm2(Phoenix Contact)
• AI0,34−10TQ 0.34 mm2(Phoenix Contact)
• AI0,5−10WH 0.5 mm2(Phoenix Contact)
• AI0,75−10GY 0.75 mm2(Phoenix Contact)
• A1−10 1.0 mm2(Phoenix Contact)
• A1,5−10 1.5 mm2(Phoenix Contact)
■
POWER SUPPLY
JC-ECT
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp
EM-9043 P. 3 / 5
MOUNTING INSTRUCTIONS
■DIN RAIL MOUNTING
• Mounting
1) Hook the upper hook at the rear side of the base onto the
DIN rail.
2) Push the lower part of the unit in the direction of the ar-
row until the base is firmly fixed to the DIN rail.
1
2
• Dismounting
1) Push down the slider using the tip of a minus screwdriver.
2) Pull out the lower part of the unit.
3) Remove the upper part of the unit from the DIN rail.
1
2
3
■SURFACE MOUNTING
1) Insert the mounter slider along the rail at the back of the
unit as shown below, and push in the rail until it clicks
once.
1
2) Fix the unit with M4 screws referring to “MOUNTING
REQUIREMENTS unit: mm (inch)” on page 5.
(Torque: 1.4 N·m)
JC-ECT
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp
EM-9043 P. 4 / 5
EXTERNAL DIMENSIONS unit: mm (inch)
50(1.97) [3(.12)]
115(4.52)[4 (.18)] [4 (.18)][7 (.28)] [7 (.28)]
[4(.16)]
73(2.87)
55(2.17)
DIN RAIL
(35 mm wide)
2–4.3 (.17) dia Mtg Hole
4 (.16) deep
CONNECTION DIAGRAM
Connect the unit as in the diagram below.
In order to improve EMC performance, bond the FG terminal to ground.
Caution: FG terminal is NOT a protective conductor terminal.
1
2
3
1
2
3
FE
PWR–
PWR+
POWER (IN)
FE
PWR–
PWR+
POWER (OUT)
+
–
RJ-45 modular jack
RJ-45 modular jack
EtherCAT (IN)
EtherCAT X2 (OUT)
RJ-45 modular jack
RJ-45 modular jack
EtherCAT X3 (OUT)
EtherCAT X4 (OUT)
RJ-45 modular jack
RJ-45 modular jack
EtherCAT X5 (OUT)*1
EtherCAT X6 (OUT)*1
RJ-45 modular jack
RJ-45 modular jack
EtherCAT X7 (OUT)*1
EtherCAT X8 (OUT)*1
*1. Available with JC-ECT-8 only.
JC-ECT
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp
EM-9043 P. 5 / 5
MOUNTING REQUIREMENTS unit: mm (inch)
125 (4.92)
SYSTEM CONFIGURATION EXAMPLE
Note) Be sure to connect the EtherCAT master device to the EtherCAT (IN) port.
EtherCAT junction slave
(Model: JC-ECT)
EtherCAT
master device
R30NECT1
R8-NECT1
Indice
Altri manuali M-system Sistema I/O
M-system
M-system Devicenet R7F4DD-DC16B-H Manuale utente
M-system
M-system R8-FS16N Manuale utente
M-system
M-system R7 Series Manuale utente
M-system
M-system R3-SS4 Manuale utente
M-system
M-system R7D-YV2/UL Manuale utente
M-system
M-system R7I4DML3-DAC32C Manuale utente
M-system
M-system R7C-YV2 Manuale utente
M-system
M-system R7D-TS4 Manuale utente
M-system
M-system R7ML-EA8 Manuale utente
M-system
M-system R7D-YS2A Manuale utente
M-system
M-system R5-SV Manuale utente
M-system
M-system R7F4HC-DA32-K Manuale utente
M-system
M-system R7M-DAC16C-R Manuale utente
M-system
M-system R7F4HEIP-DAC16B Manuale utente
M-system
M-system R7M-CT4E-R Manuale utente
M-system
M-system R7 Series Manuale utente
M-system
M-system R7D-CT4E Manuale utente
M-system
M-system MDR-8 Manuale utente
M-system
M-system R3-CT8B Manuale utente
M-system
M-system R7ML-LC2-R Manuale utente
Manuali Sistema I/O popolari di altre marche
WAGO
WAGO 750-344 Manuale utente
Teknim
Teknim TWM-1887 Manuale di istruzioni
Intelligent Appliance
Intelligent Appliance IA-2662-E Manuale utente
BERGHOF
BERGHOF ECC DIO 16/16 Manuale di istruzioni
Advantech
Advantech PCM-27J3AU Manuale di installazione e funzionamento
Festo
Festo CP-E08-M12-CL Manuale utente
