M-system R80UST4 Manuale utente
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp
EM-7028 P. 1 / 9
INSTRUCTION MANUAL
UNIVERSAL INPUT MODULE
(4 points, isolated, tension clamp terminal block) MODEL R80UST4
BEFORE USE ....
Thank you for choosing M-System. Before use, please check
contents of the package you received as outlined below.
If you have any problems or questions with the product,
please contact M-System’s Sales Office or representatives.
■PACKAGE INCLUDES:
Universal input module ......................................................(1)
CJC sensor...........................................................................(4)
■MODEL NO.
Confirm Model No. marking on the product to be exactly
what you ordered.
■INSTRUCTION MANUAL
This manual describes necessary points of caution when
you use this product, including installation, connection and
basic maintenance procedures.
POINTS OF CAUTION
■CONFORMITY WITH EU DIRECTIVES
• The equipment must be mounted inside a panel.
• The actual installation environments such as panel con-
figurations, connected devices, connected wires, may af-
fect the protection level of this unit when it is integrated
in a panel system. The user may have to review the CE
requirements in regard to the whole system and employ
additional protective measures to ensure the CE conform-
ity.
■GENERAL PRECAUTIONS
• Before you remove or mount the unit, turn off the power
supply and output signal for safety.
• DO NOT set the switches while the power is supplied.
The switches are used only for maintenance without the
power.
■ENVIRONMENT
• Indoor use.
• When heavy dust or metal particles are present in the
air, install the unit inside proper housing with sufficient
ventilation.
• Do not install the unit where it is subjected to continuous
vibration. Do not subject the unit to physical impact.
• Environmental temperature must be within -10 to +55°C
(14 to 131°F) with relative humidity within 30 to 90% RH
in order to ensure adequate life span and operation.
■WIRING
• Do not install cables close to noise sources (relay drive
cable, high frequency line, etc.).
• Do not bind these cables together with those in which
noises are present. Do not install them in the same duct.
■POWER UP
• Turn the power on at the same time as the power/network
module or turn the R80PS1 on before the power/network
module turned on. If the R80PS1 is not turned on within
3 seconds after the power/network module is turned on,
I/O modules are not correctly recognized.
R80UST4
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp
EM-7028 P. 2 / 9
INSTALLATION
■HOW TO MOUNT THE MODULE ON DIN RAIL
Confirm that the locking clamps of the extension power supply module
are set. Insert the module in parallel to the next one while aligning the
grooves of both modules (A & B in the above figure).
Maintain it perpendicularly to the rail.
More I/O modules can be added in the same manner.
A
B
• Protective Cover
The protective cover is to be attached over the connected I/O module
at the right end.
Align the hooks on the cover with the grooves of the module and slide it
straight until the hooks are latched.
When removing the cover, pull it out while squeezing the hooks inward.
Groove
Hook
R80UST4
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp
EM-7028 P. 3 / 9
■HOW TO UNMOUNT THE MODULE FROM DIN RAIL
Release the locking clamps and pull out straight the module.
Caution !
1)Be careful not to hurt your hand by pointed edges of the internal bus
connector.
2) I/O modules cannot hold tightly on the DIN rail by themselves without
power/network module.
Secure them to the position if necessary by using DIN rail end plates.
• Removing an intermediate module
R80UST4
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp
EM-7028 P. 4 / 9
COMPONENT IDENTIFICATION
Status Indicator LED
Input Status Indicator LED
Internal Bus Connector
Input Connector
Terminator DIP SW
SW2
On
2
1
SW1
On
4
3
2
1
Module Address
DIP SW
■STATUS INDICATOR LED / INPUT STATUS INDICATOR LED
LED OPERATION COLOR FUNCTION
RUN ON Red Upper communication: Stopping or abnormal
Internal communication: Abnormal
ON Green Upper communication: Normal
Internal communication: Normal
Blink
1 sec. sycle
– Burnout is detected or with input value error
(≤ -15%, ≥ +115%, becomes less than the lower limit or exceeds the
upper limit of usable range).
Blink
400 msec. cycle
– Input circuit abnormality (AD converter response failure)
OFF – Upper communication: Stopping or abnormal
Internal communication: Normal
Input Status Indi-
cator LED
OFF Red Input data in the range
ON Burnout is detected or with input value error
(≤ -15%, ≥ +115%, becomes less than the lower limit or exceeds the
upper limit of usable range).
Input circuit abnormality (AD converter response failure)
R80UST4
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp
EM-7028 P. 5 / 9
■OPERATING MODE SETTING
(*) factory default setting
Note. Be sure to OFF the unused SW2-2.
• Module Address Setting
Configurate the mosule address with DIP Switch.
0 - 15 are available for module address.
MODULE
ADDRESS
SW1
1234
0(*) OFF OFF OFF OFF
1 ON OFF OFF OFF
2 OFF ON OFF OFF
3 ON ON OFF OFF
4 OFF OFF ON OFF
5 ON OFF ON OFF
6 OFF ON ON OFF
7 ON ON ON OFF
8 OFF OFF OFF ON
9 ON OFF OFF ON
10 OFF ON OFF ON
11 ON ON OFF ON
12 OFF OFF ON ON
13 ON OFF ON ON
14 OFF ON ON ON
15 ON ON ON ON
• Terminator Setting
Terminator SW2-1
Disabled (*) OFF
Enabled ON
■INPUT CONNECTOR TERMINAL ASSIGNMENT
1
2
3
4
5
6
7
8
PIN NO. ID FUNCTION
1 U1 U1
2 NC Unused
3 NC Unused
4 U6 U6
5 U2 U2
6 U3 U3
7 U4 U4
8 U5 U5
• Universal input terminal assignment
ID
FUNCTION
Wide span voltage
(-10 - +10V DC)
DC Current Narrow span voltage
(-1000 - +1000mV DC)
Thermocouple
RTD/
Resistor (3-wire)
RTD/
Resistor (2-wire)
Potentiometer
U1
Wide span voltage
– – – – – –
U2 –
DC Current
– – – – –
U3 – – Narrow span voltage
Thermocouple+
RTD-b – Input S
U4 – – – CJM RTD-B RTD-B Input L
U5 Common Common Common
Thermocouple-
RTD-A RTD-A Input H
U6 – – – CJM – – –
R80UST4
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp
EM-7028 P. 6 / 9
PC CONFIGURATOR
The following parameters can be set with using PC Configurator Software (model: R80CFG)
Refer to the users manual for the R80CFG for detailed operation of the software program.
■CHANNEL INDIVIDUAL SETTING
ITEM SETTING RANGE DEFAULT VALUE
Unused setting CH enabled
CH disabled
CH enabled
Input type DC voltage -10 - +10 V DC
-1000 - +1000 mV DC
-10 - +10 V DC
DC current -20 - +20 mA DC
Potentiometer POT 0 - 4000 Ω
POT 0 - 2500 Ω
POT 0 - 1200 Ω
POT 0 - 600 Ω
POT 0 - 300 Ω
POT 0 - 150 Ω
Resistpr OHM 0 - 4000 Ω
RTD RTD Pt 100
RTD Pt 500
RTD Pt 1000
RTD Pt 50 Ω
RTD JPt 100
RTD Ni 508.4 Ω
RTD Cu 10
Thermocouple TC (PR)
TC K
TC E
TC J
TC T
TC B
TC R
TC S
TC C
TC N
TC U
TC L
TC P
Wiring 2-wire
3-wire
-
Burnout Upscale
Downscale
None
-
CJC Enabled
Disabled
-
Temp. unit degC
degF
K
-
Zero fine adj. -320.00 - +320.00 (%) 0.00 (%)
Gain fine adj. -3.2000 - +3.2000 1.0000
Zero base depends on input types*10.000
Full base depends on input types*10.000
Zero scaling -32,000 - +32,000 0
Full scaling -32,000 - +32,000 10,000
First order lag filter 0.0, 0.5 - 60.0 (sec.) 0.0 (sec.)
*1. For details, refer to the users manual of R80CFG
■CHANNEL BATCH SETTING
ITEM SETTING RANGE DEFAULT VALUE
Version no. – –
Simulate input Normal input
Simulated data
Normal input
R80UST4
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp
EM-7028 P. 7 / 9
TERMINAL CONNECTIONS
Connect the unit as in the diagram below.
For thermocouple input, attach the CJC sensor together with input wining to the input screw terminals.
■EXTERNAL DIMENSIONS unit : mm (inch)
24 [.94] (3 [.12])
55 [2.17]
67 [2.64] (4 [.16])
115 [4.53] 6 [.24]6 [.24]
7 [.28] 7 [.28]
DIN rail
(35mm wide)
R80UST4
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp
EM-7028 P. 8 / 9
■CONNECTION DIAGRAM
1
3
2
4
8
7
6
5
1
3
2
4
8
7
6
5
1
3
2
4
8
7
6
5
1
3
2
4
8
7
6
5
CONNECTOR
INTERNAL BUS
INTERNAL POWER
U1
U1
U1
U1
U2
U3
U4
U5
U6
NC
NC
U2
U3
U4
U5
U6
NC
NC
U2
U3
U4
U5
U6
NC
NC
U2
U3
U4
U5
U6
NC
NC
Universal input 1
Universal input 2
Universal input 3
Universal input 4
FE
R80UST4
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp
EM-7028 P. 9 / 9
U3
U1
U2
U6
U5
U4
INPUT
+
−
U3
U1
U2
U6
U5
U4
INPUT
+
−
• DC Voltage (-10‑+10V DC) • DC Current (0 ‑20mA DC)
■UNIVERSAL INPUT CONNECTION
• RTD or Resistor (3-wire)
• DC Voltage (-1000 ‑+1000mV DC)
• Thermocouple • Potentiometer• RTD or Resistor (2-wire)
U3
U1
U2
U6
U5
U4
INPUT
+
−
U3
U1
U2
U6
U5
U4
U3
U1
U2
U6
U5
U4
U3
U1
U2
U6
U5
U4
U3
U1
U2
U6
U5
U4
+
‒–
A
B
B
A
B
max.
min.
+
−
WIRING INSTRUCTIONS
■TENTION CLAMP TERMINAL BLOCK
Unit side connector: DMC0,5/4-G1-2,54 P20THR R44
(Phoenix Contact)
Cable side connector: DFMC0,5/4-ST-2,54
(Phoenix Contact)
Applicable wire size: 0.14 − 0.5 mm2
Stripped length: 7 mm
Recommended solderless terminal
• AI0,14-6GY0.14mm2(Phoenix Contact)
• AI0,25-6YE0.25mm2(Phoenix Contact)
• A0,34-70.34mm2(Phoenix Contact)
Indice
Altri manuali M-system Sistema I/O
M-system
M-system R30NE1 Manuale utente
M-system
M-system R7L-EA16 Manuale utente
M-system
M-system R7D-TS4/UL Manuale utente
M-system
M-system R7D-TS4 Manuale utente
M-system
M-system M6 Series Manuale utente
M-system
M-system R3-DC64A Manuale utente
M-system
M-system R7E-MS4 Manuale utente
M-system
M-system R80DCT16A2 Manuale utente
M-system
M-system R5-SV Manuale utente
M-system
M-system R7L-DC16B-R Manuale utente
M-system
M-system R7L-SV4 Manuale utente
M-system
M-system Mini-MW Series Manuale utente
M-system
M-system R8-SS4N Manuale utente
M-system
M-system R3-DA64A Manuale utente
M-system
M-system R3-SS8 Manuale utente
M-system
M-system R3-CT8A Manuale utente
M-system
M-system R7L-DAC16 Manuale utente
M-system
M-system R30MS4 Manuale utente
M-system
M-system Devicenet R7F4HD-DA32B Manuale utente
M-system
M-system JC-IO Manuale utente
Manuali Sistema I/O popolari di altre marche
WAGO
WAGO 750-344 Manuale utente
Teknim
Teknim TWM-1887 Manuale di istruzioni
Intelligent Appliance
Intelligent Appliance IA-2662-E Manuale utente
BERGHOF
BERGHOF ECC DIO 16/16 Manuale di istruzioni
Advantech
Advantech PCM-27J3AU Manuale di installazione e funzionamento
Festo
Festo CP-E08-M12-CL Manuale utente
