M2 Antenna Systems 7-10-30LP8 Manuale utente

FOR CONVERTING THE 10-30LP8 TO A 7-10-30LP8 'SKIP LOG'

OVERVIEW OF UPGRADE: Very little has to be done to your original 10-30LP8. In fact the only element that you even

work on is the longest element. If it is possible to remove just the rear element and leave the rest of the antenna up, that

would be the easiest. Please look over the ASSEMBLY DETAILS AND TUNING CHART before beginning and familiarize

yourself with the new parts to be added. Note the basic element sections do not change in any way.

Refer to the two “add-on” assembly drawings for screw and bolt sizes when not called out in the text.

NOTE: WHEN USING THE 5/64” ALLEN WRENCH PROVIDED BE SURE THAT IT IS FULLY INSERTED INTO THE 8

-32 SET SCREWS TO BE SURE FULL TORQUE CAN BE APPLIED WITHOUT STRIPPING THE SET SCREW.

1. Begin by installing the VERTICAL SUPPORT TUBE. Remove the two center bolts in the element clamp plates. Feed

the 1/4-20 x 3 1/2 bolts through the clamp plate holes and add the 1/4-20 locknuts. Tighten securely.

NOTE: If you have our early version log periodic, the bolt pattern may not match the square tube holes. Place

the square tube in position, mark the plate where the holes should be and drill 1/4" holes through your clamp

plates. Then assemble as noted above.

2. Refer to the 7-10-30LP8 element# 1 assembly detail drawings and prepare each element half by adding the STABI-

LIZER INSULATOR, DUAL WING SKIP SUPPORT ARMS AND ELEMENT OVERHEAD SUPPORT CLAMP. Then

add the 3/4” AND 1/2” LINEAR LOADING ARMS. Do this by opening the element joints on each element half and

sliding on the parts to their approximate positions as shown. Then reconnect the element joints. Finalize the positions

of the parts as describe in the drawings. The white plastic rod insulators can be installed at this time in each support

arm.

3. Place the element on a level surface with the support post up. FROM THE ELEMENT BUTT SIDE, feed a 3/16” x 72”

LINEAR LOADING ROD through the flat support insulator and on to the un-insulated side of the DUAL SUPPORT

ARM until 5/8” extends beyond arm. Install (4) and tighten the (2) 8-32 x 1/4" set screws locking this rod in place.

Install two SHAFT RETAINERS, one at a time, onto this rod tip and snug up to linear loading arm.

NOTE: to start the RETAINER, hold the 3/8 x 3" PUSH TUBE in your hand with one end between your thumb

and forefinger. Now center retainer on this end, “dish” into tube, and hold in place with the same thumb and

forefinger. Grasp the linear loading rod near the end with your other hand and firmly push the retainer onto

the rod.

4. In the same way, feed another 72” LINEAR LOADING ROD through the flat support insulator and on through the

white polyethylene insulator until 5/8” extends beyond insulator. Tighten the (2) 8-32 /4” set screws locking the rod in

the arm. Install two SHAFT RETAINERS, one at a time, onto this rod tip and snug up to insulator. Install two 8-32 x

1/4” set screws into a 1/4” x 1/2” x 1” SPLICE BLOCK and install block on 1/2” rod tip up against the retainers. Tight-

en set screw. Repeat for other element half.

M2 Antenna Systems, Inc. 4402 N. Selland Ave. Fresno, CA 93722

Tel: (559) 432-8873 Fax: (559) 432-3059 Web: www.m2inc.com

11/13/17

Rev.01

M2 Antenna Systems, Inc.

Model No: 7-10-30LP8 UP-KIT

5. Insert (2) 8-32 x 1/4” set screws into each remaining SPLICE BLOCK. Slide a splice block 1/2” on the open

ends of each of the rods just installed and tighten the set screw.

Now insert two more 3/16” x 72” rods per side into these SPLICE BLOCKS and tighten the set screws.

6. Slide another 3/16” x 72” rod through the white insulators on the 3 arms beyond the dual support arm. In-

sert the inner rod end into splice block at the dual support arm and tighten set screw. Now slide the sec-

ond 72” rod in through the white insulators and connect it at the spice block as before. SEE THE FRE-

QUENCY CHART on the LINEAR LOADED ELEMENT ASSEMBLY DRAWING and select the desired

center frequency for Element #1. Cut this outer linear loading rod to the desired dimension. Position the

outermost linear loading arm about 6” from tip. Space the other arms to support the rod at equal intervals.

Then tighten all clamp screws. Repeat for other element half.

7. Next, pre-assemble both pair of LINEAR LOADING SHORTING BARS using (5) 8-32 x 7/8” screws and

locknuts. NOTE: THE BARS ARE NOT SYMMETRICAL IN THE CENTER GROOVES. Now pass about 4”

of HPTG-1200 through the CENTER groove and back through the offset grooves so you have about 2-1/2

inches of cable end coming back for later clamping. Using a tape measure, mark each rod at the “A” Dim.

back from where it attaches to the DUAL SUPPORT ARM. Slide a shorting bar set onto the rod ends and

position the shorting bar clamps at your “A” Dim. marks. Level the bars; equalize the rod tension and begin

tightening the outer screws. Once everything is straight and aligned, tighten all 5 screws. Repeat for the

other side.

NOTE: IF YOU WILL BE USING THIS ANTENNA FOR OPERATION BELOW 6.950 MHZ, THEN DO NOT

TRIM OFF THE EXCESS ROD BEYOND THE SHORTING BAR. CONSULT THE TUNING CHART FOR

THE PROPER SHORTING BAR SETTING AND THEN TRIM OFF EXCESS 5” BEYOND THE SHORT-

ING BARS.

IF OPERATION IS DESIRED ABOVE 6.950 MHZ, THEN CUT THE EXCESS ROD MATERIAL OFF AT 5”

BEYOND THE SHORTING BARS.

EXCESS ROD MUST BE TRIMMED AS DESCRIBED ABOVE OR RESONANCE MAY BE

LOWER.

8. Cut the 30 ft. phillystran into to equal length and route through the element support clamps and pull tight.

(see the self locking method shown in the assembly details diagram). Route the other end of the cable

through the thimble and upper turnbuckles and wire clips and pull tight and tighten the clips, equally ten-

sion the cables using the turnbuckle. To check your tension, lift the element up at the center and note the

element droop. Each element should droop 10” to 16” at the tip.

9. Now route the linear loading phillystran through the lower turn buckles and thimbles and add the wire clips.

Pull the cable though and tighten the wire clips. Use the turnbuckles to tension them just to slightly help

the main element supports. Use 1/4-20 nuts provided to jam the turnbuckle.

10. We have provided a new coil section to go across the rear element which is different from some earlier

coils. If this coil is different from your original, replace the original with this new coil. FINAL CHECK ALL

HARDWARE FOR TIGHTNESS.

THIS COMPLETES THE ASSEMBLY PROCESS.

NOTE: When mounting this log periodic on a tower or mast with other antennas there may be interaction par-

ticularly if any of the other antennas are resonant in the 7 AND 10 to 30 MHz band. In general VHF and/or

UHF antennas mounted for HORIZONTAL POLARITY should be at least 40 inches above or below the log

antenna. Use good quality 50 Ohm feed line to feed the log and be sure your tower and rotator system can

handle to wind area and weight of this antenna. We want you to enjoy operating the SEVEN AMATEUR

BANDS that this antenna covers not to mention all the other possible applications for this versatile performer!

ASSEMBLY INSTRUCTIONS

7-10-30L8 DIMENSION SHEET

7-10-30LP8 ELEMENT#1

ASSEMBLY DETAILS

ELEMENT #1 OVERHEAD SUPPORT

TURNBUCKLE

1/4” X 4”

7-10-30LP8 ELEMENT#1

ASSEMBLY DETAILS

ELEMENT OVERHEAD

SUPPORT CLAMP DETAIL

NOTE:THIS PICTURE MAY NOT BE SPECIFIC TO YOUR ANTENNA.

GENERIC PICTURE USED TO SHOW ELEMENT OVERHEAD

SUPPORT CLAMP TIE DOWN DETAIL.

7-10-30-LP8 LINEAR LOADING (TUNING)

ELEMENT

OVERHEAD

SUPPORT

CLAMP

1”

DESCRIPTION QTY

SUPPORT POST, LL, 1” X 1” X 24” (M2AVR0050) .............................................. 1

ELEMENT OVERHEAD SUPPORT CLAMP (M2APL0212) ................................. 2

ELEMENT OVERHEAD SUPPORT LINE, HPTG1200 X 30’................................ 1

STEPPED INSULATOR (M2APL0037) ................................................................. 2

LINEAR LOADING INSULATOR (M2APL0038).................................................... 6

SPLICE BLOCK (M2APL0036).............................................................................. 8

SKIP SUPPORT ARM, DUAL WING, 3/8 X 1 1/2 X 5.750 (M2APL0020) ............ 2

LINEAR LOADING SUPPORT ARM, 1/2” X 3/4” (M2APL0015) ........................... 4

LINEAR LOADING SUPPORT ARM, 1/2” X 1/2” (M2APL0014) ........................... 2

INSULATOR, STABILIZER BAR 1/4 X 1 X 6”, ABS (M2APL0200)...................... 2

SUPPORT ARM FOR STABILIZER BAR, (1” HOLE) (M2APL0201).................... 2

SHORTING BAR HALVES, 1/4 X 3/4 X 5.875" (M2ASB0250) ............................ 4

STRAIN RELIEF, BLACK DELRIN (M2APL0100)................................................. 2

HPTG-1200 X 36” PHILLYSTRAN ........................................................................ 2

ASSEMBLY MANUAL............................................................................................ 1

LINEAR LOADING RODS, 3/16" X 72" ............................................................... 12

HARDWARE

TURN BUCKLE, 1/4-20 X 4”, HOOK AND EYE .................................................... 4

BOLT, 1/4-20 X 3 3/4” STAINLESS....................................................................... 2

NUT, 1/4-20 LOCKING, STAINLESS .................................................................... 4

NUT, 1/4-20, STAINLESS...................................................................................... 2

SCREW, 8-32 X 1-1/2" PANHEAD, STAINLESS ................................................ 10

SCREW, 8-32 X 1-1/4" PANHEAD, STAINLESS .................................................. 4

SCREW, 8-32 X 1.0" PANHEAD, STAINLESS ................................................... 16

SCREW, 8-32 X 7/8” PANHEAD, STAINLESS ................................................... 10

NUT, 8-32 LOCKING, STAINLESS ..................................................................... 38

SET SCREW, 8-32 X 1/4 STAINLESS ................................................................ 20

KEEPER, 3/16 STAINLESS................................................................................... 8

CABLE CLIPS, 1/8”................................................................................................ 8

CABLE EYE, 3/16”................................................................................................. 4

PUSH TUBE 3/8 X 3" ALUM.................................................................................. 1

ALLEN WRENCH, 5/64” ........................................................................................ 1

M2 ANTENNA SYSTEMS, INC.

4402 N. SELLAND AVE

FRESNO, CA 93722

559-432-8873 FAX 432-3059

www.m2inc.com Email: [email protected]

7-10-30LP8 UP-KIT PARTS & HARDWARE

Indice

Altri manuali M2 Antenna Systems Antenna

M2 Antenna Systems

M2 Antenna Systems 303CP26 Manuale utente

M2 Antenna Systems

M2 Antenna Systems FD35.5 Manuale utente

M2 Antenna Systems

M2 Antenna Systems 40M2C Manuale utente

M2 Antenna Systems

M2 Antenna Systems 7-10-30LP8 UP-KIT Manuale utente

M2 Antenna Systems

M2 Antenna Systems 440-6SX Manuale utente

M2 Antenna Systems

M2 Antenna Systems 40M3FS Manuale utente

M2 Antenna Systems

M2 Antenna Systems 393CP18 Manuale utente

M2 Antenna Systems

M2 Antenna Systems 6M3 Manuale utente

M2 Antenna Systems

M2 Antenna Systems 2M5WL Manuale utente

M2 Antenna Systems

M2 Antenna Systems 30M3-125 Manuale utente

M2 Antenna Systems

M2 Antenna Systems 436CP42UG Manuale utente

M2 Antenna Systems

M2 Antenna Systems 2MCP22 Manuale utente

M2 Antenna Systems

M2 Antenna Systems 420-450-11HP Manuale utente

M2 Antenna Systems

M2 Antenna Systems 41-3BB Manuale utente

M2 Antenna Systems

M2 Antenna Systems EB-144/RK2M Manuale utente

M2 Antenna Systems

M2 Antenna Systems 436CP30 Manuale utente

M2 Antenna Systems

M2 Antenna Systems 32 HO LOOP Manuale utente

M2 Antenna Systems

M2 Antenna Systems 222XP30 Manuale utente

M2 Antenna Systems

M2 Antenna Systems 10M4DX Manuale utente

M2 Antenna Systems

M2 Antenna Systems 44.5-5 Manuale utente

M2 Antenna Systems

M2 Antenna Systems 2M4 Manuale utente

M2 Antenna Systems

M2 Antenna Systems 300XP12 Manuale utente

M2 Antenna Systems

M2 Antenna Systems 6M HO LOOP Manuale utente

M2 Antenna Systems

M2 Antenna Systems 35.7-4 Manuale utente

Manuali Antenna popolari di altre marche

Alfa Network

Alfa Network APA-L01 Manuale utente

Naval

Naval PR-422CA Manuale utente

Feig Electronic

Feig Electronic ID ISC.ANTH200/200 Series Manuale utente

TERK Technologies

TERK Technologies TV44 Manuale utente

Directive Systems & Engineering

Directive Systems & Engineering DSE2324LYRMK Manuale utente

HP J8999A Manuale utente

MobilSat

MobilSat MSP-S Manuale utente

Steren

Steren ANT-UHF 13 Manuale utente

Novatel

Novatel 600-G Manuale operativo

Radio Shack

Radio Shack Amplified VHF/UHF/FM Indoor Antenna Manuale utente

TRENDnet

TRENDnet TEW-AO12O Manuale utente

Radio Shack

Radio Shack 15-1837 Manuale utente

CommScope

CommScope CMAX-OMFX-43M-I53 Manuale utente

Ramsey Electronics

Ramsey Electronics DAP25 Manuale utente

COBHAM

COBHAM SAILOR 800 VSAT Manuale per l'uso e la cura

Trango Systems

Trango Systems AD900-9 Manuale utente

Steren

Steren ANT-100 Manuale utente

Proxim

Proxim 5054-PA-23 Manuale utente