Magnetek Flex I-Chip Manuale utente

Flex I-Chip

Remote Crane Controls

August 2010

Part Number: 198-50014

Flex I-Chip Remote Crane Controls

August 2010

2 of 28

U.S. Service Information

For questions regarding service or technical information contact:

1.866.MAG.SERV

(1.866.624.7378).

Magnetek Material Handling

N49 W13650 Campbell Drive

Menomonee Falls, WI 53051

Telephone: 800.288.8178

Website: www.magnetekmh.com

e-mail: [email protected]

Fax Numbers:

Main: 800.298.3503

Sales: 262.783.3510

Service: 262.783.3508

Canada Service Information:

4090B Sladeview Crescent

Mississauga, Ontario

L5L 5Y5 Canada

Phone: 1.800.792.7253

Fax: 1.905.828.5707

limited to, this manual and software embodied within the product. This manual is intended for the sole use of the

person(s) to whom it was provided, and any unauthorized distribution of the manual or dispersal of its contents is

strictly forbidden. This manual may not be reproduced in whole or in part by any means whatsoever without the

expressed written permission of MAGNETEK.

Flex I-Chip Remote Crane Controls

August 2010

3 of 28

PRODUCT MANUAL SAFETY INFORMATION

Magnetek, Inc. (Magnetek) offers a broad range of radio remote control products, control products and adjustable

frequency drives, and industrial braking systems for overhead material handling applications. This manual has

been prepared by Magnetek to provide information and recommendations for the installation, use, operation and

service of Magnetek’s material handling products and systems (Magnetek Products). Anyone who uses,

operates, maintains, services, installs or owns Magnetek Products should know, understand and follow our

instructions and safety recommendations in this manual for Magnetek Products.

The recommendations in this manual do not take precedence over any of the following requirements relating to

cranes, hoists and lifting devices:

Instructions, manuals, and safety warnings of the manufacturers of the equipment where the radio system

is used,

Plant safety rules and procedures of the employers and the owners of facilities where the Magnetek

Products are being used,

Regulations issued by the Occupational Health and Safety Administration (OSHA),

Applicable local, state or federal codes, ordinances, standards and requirements, or

Safety standards and practices for the overhead material handling industry.

This manual does not include or address the specific instructions and safety warnings of these manufacturers or

any of the other requirements listed above. It is the responsibility of the owners, users and operators of the

Magnetek Products to know, understand and follow all of these requirements. It is the responsibility of the owner

of the Magnetek Products to make its employees aware of all of the above listed requirements and to make certain

that all operators are properly trained. No one should use Magnetek Products prior to becoming familiar

with and being trained in these requirements.

WARRANTY INFORMATION

FOR INFORMATION ON MAGNETEK’S PRODUCT WARRANTIES BY PRODUCT TYPE, PLEASE VISIT

WWW.MAGNETEKMH.COM.

Flex I-Chip Remote Crane Controls

August 2010

4 of 28

Table of Contents

A. Exterior Illustrations...................................................................................................................................... 5

B. Testing Complete Transmitter ...................................................................................................................... 6

C. Testing Encoder Board.................................................................................................................................. 7

D. Testing Receiving Module............................................................................................................................. 9

E. Decoder Module Programming .................................................................................................................. 10

F. I-Chip programming......................................................................................................................................11

1. LCD and keypad illustrations...................................................................................................................11

2. Copy I-Chip.................................................................................................................................................11

3. Program System Serial Number.............................................................................................................. 12

4. Program System Type.............................................................................................................................. 12

5. Program Start/Aux Function.................................................................................................................... 12

6. Program Transmitter Output Power ....................................................................................................... 13

7. Program Transmitter On Time / Transmitting Time............................................................................... 13

8. Program System RF Channel.................................................................................................................. 13

9. Program Transmitter Push Button Functions ....................................................................................... 13

Table A-1. Transmitter Toggle with LED Displays................................................................................... 14

Table A-2. Inline Transmitter Toggle with LED Displays ........................................................................ 14

Table B-1. A/B Push Button Select........................................................................................................... 16

Table B-2. Inline A/B Push Button Select................................................................................................. 19

Table C-1. Combination of Transmitter Toggle + A/B Push Button Select........................................... 23

Table C-2. Combination of Transmitter Toggle + A/B Push Button Select........................................... 26

10. BRAKE Function (not required if programmed directly on the decoder module - Section E) ......... 27

11. PASSWORD / Security Code Function................................................................................................... 27

Flex I-Chip Remote Crane Controls

August 2010

5 of 28

A. Exterior Illustrations

1) Fuse(1.0A) 8) Power cable to encoder board

2) Power LED 9) Cable to encoder board’s CN1 connector

3) SQ1 LED (internal receiving module) 10) Cable to I-Chip slot on decoder modules

4) I-Chip LED 11) Test mode select button

5) SQ2 LED (external receiving module) 12) External receiving module input slot

6) I-Chip slot 13) External power input slot (not provided)

7) Internal battery compartment 14)Powerswitch

Flex I-Chip Remote Crane Controls

August 2010

6 of 28

B. Testing Complete Transmitter

To check if the transmitter handset is in good order please follow the instruction below.

1) Press the Test Mode Select button until the LCD screen displays “Testing Complete Transmitter 1”.

2) The LCD screen is displayed as follows:

Testing Complete Transmitter

S - - - - - - T - - M - - CH 01

↓↓↓↓

Serial number Type Mode Channel

3) First set this unit’s channel identical to the one set on the transmitter handset to be tested via the ↑& ↓

push buttons on the keypad.

4) Turn on the transmitter and rotate the power key to Start position.

5) At this time the SQ1 LED should blink red with the transmitter information displayed on the LCD screen.

If SQ1 LED does blink red but does not have the transmitter information shown on the LCD screen then

the encoder board is defective. If nothing is shown at all (both SQ1 LED and transmitter information),

then either the internal transmitting board or the encoder board is defective. If this is the case, then

proceed to section C to check the transmitting board and encoder board.

6) If SQ1 LED does blink red with the transmitter information shown on the LCD screen then go on to

check all the push button commands.

7) Press all the push buttons on the transmitter, one at a time, to check if this unit decodes all the

pushbutton commands. When a push button is pressed, an arrow should appear below the system

information, for both 1st and 2nd steps. If not, then the encoder board is defective. If only one or two push

buttons do not display the arrows on the LCD screen when pressed, then those push buttons are

defective.

8) If all the information is correct then the transmitter handset is in good order. Go on to section D to

Flex I-Chip Remote Crane Controls

August 2010

7 of 28

check the receiving module.

C. Testing Encoder Board

To check if the encoder boards is in good order please follow the instructions below.

1) Press the Test Mode Select button until the LCD screen displays “Testing Encoder Board 5”.

2) The LCD screen is displayed as follows:

Testing Encoder Board

S - - - - - - T - - M - -

↓↓↓

Serial number Type Mode

3) Plug all the required cables onto this unit

4) Plug all the cables from this unit to the encoder board.

Flex I-Chip Remote Crane Controls

August 2010

8 of 28

5) Make sure the encoder board has an I-Chip installed.

6) Press and hold on to the power switch.

7) Press the Start micro switch one time and let go. The LED 1 should blink green.

8) At this time the LCD screen should display the transmitter I-Chip information. If not, then the encoder

board is defective.

9) If the LCD screen does display transmitter information correctly, then press all the push buttons on the

encoder board one at a time to see if the unit decodes all the pushbutton commands. When a push

button is pressed, an arrow should appear below the system information displays, for both 1st and 2nd

steps. If not, then the encoder board is defective. If only one or two push buttons do not display the

arrows on the LCD screen when pressed, then those push buttons are defective.

10) If all the information is correct then the encoder board is in good order. If this is the case, then the

transmitting board is defective.

Flex I-Chip Remote Crane Controls

August 2010

9 of 28

D. Testing Receiving Module

To check if the receiving module is in good order please follow the instructions below.

1) Press the Test Mode Select button until the LCD screen displays “Testing Receiver Module 2”.

2) The LCD screen is displayed as follows:

Testing Receiving Module

S - - - - - - T - - M - -

↓↓↓

Serial number Type Mode

3) Plug the receiving module to be tested on to this unit.

4) Use a good transmitter handset (any type) to test the receiving module.

5) Set the channel dip switch on the receiving module to the one set on the transmitter.

6) Turn the transmitter power on and rotate the power key to the Start position. The SQ2 LED should light

up or blink; if not, then the receiving module is defective.

7) If SQ2 LED blinks red with all the transmitter information shown on the LCD screen then the decoder

module is defective.

Flex I-Chip Remote Crane Controls

August 2010

10 of 28

E. Decoder Module Programming

You can program the serial number, system type, Start/Aux, brake function and service date onto the decoder

module.

1) Plug all the required cables onto this unit.

2) Plug the cable from this unit to the I-Chip slot on the decoder module.

3) Press the Test Mode Select button until the LCD screen displays “Decoder Programming 4”.

4) Set the serial number, system type, Start/Aux and brake function by using Next, Previous, ↑& ↓arrows

and keypad. Press Copy button when done.

Indice

Altri manuali Magnetek Telecomando

Magnetek

Magnetek FLEX-6EX Manuale utente

Magnetek

Magnetek Flex Pro Series Manuale utente

Magnetek

Magnetek FLEX BASE Manuale utente

Magnetek

Magnetek Flex 12EX System Manuale utente

Magnetek

Magnetek flex 4es Manuale utente

Magnetek

Magnetek Flex Pro Tethered Controller Manuale utente

Magnetek

Magnetek Flex 8RS System Manuale utente

Magnetek

Magnetek FLEX BASE Manuale utente

Magnetek

Magnetek FLEX MINI Manuale utente

Magnetek

Magnetek CPA HPV 900 Axial Flux PM Series Manuale utente

Magnetek

Magnetek FLEX BASE Manuale di servizio

Magnetek

Magnetek FLEX EX2 Manuale utente

Magnetek

Magnetek Mini-MBT Transmitter Engineered Manuale utente

Magnetek

Magnetek Flex 4EX2 Manuale utente

Magnetek

Magnetek Enrange Flex EX Manuale utente

Magnetek

Magnetek Flex EM HazLoc Manuale utente

Magnetek

Magnetek Flex 12EX2 Manuale utente

Magnetek

Magnetek Telemotive MLTX2 Manuale utente

Magnetek

Magnetek Flex 4Base Manuale utente

Magnetek

Magnetek Flex 12EX System Manuale utente

Manuali Telecomando popolari di altre marche

Panasonic

Panasonic EUR7622KB0 Manuale utente

Bang & Olufsen

Bang & Olufsen Beo4 Manuale utente

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Manuale utente

Multiplex

Multiplex PROFI TX 9 Manuale utente

One Remote

One Remote RMB4 Manuale utente

FUTABA

FUTABA 9ZAP - PART2 Manuale utente

HR Matic

HR Matic HR MULTI 3 Manuale utente

Yamaha

Yamaha ACC-GNRST-30-20 Manuale utente

EisSound

EisSound KBSOUND Manuale utente

Marantz

Marantz RC101 Manuale utente

Conrad

Conrad FS20 TC6 Manuale utente

Anritsu

Anritsu MP1777A Manuale utente

Niles

Niles WVC100 Guida alla risoluzione dei problemi

RCA

RCA RCU1300 Manuale utente

Bang & Olufsen

Bang & Olufsen BEO6 Manuale utente

GE 94901 Manuale utente

Onbon

Onbon YQ1-75 Manuale utente

FUTABA

FUTABA R7108SB Istruzioni per l'installazione