MakerBot Labs Experimental Extruder Manuale utente

CONFIGURATION AND NOZZLE CHANGING GUIDE

NOTE: The Experimental Extruder is an experimental product and is not covered under warranty or MakerCare.

STEP ONE:

Choose your Experimental Extruder configuration:

Remove the

Active Cooling Duct

by pulling down.

Ensure the Replicator Z18

Swivel Clip is attached.

You may optionally remove

the Replicator Z18 Swivel

Clip and replace it with the

Extruder Top Cap

(may perform better with

certain materials).

Remove the Replicator

Z18 Swivel Clip and

replace it with the

Extruder Top Cap.

Make sure the Active Cooling

Duct is snapped into place —

opening toward the back.

›MakerBot®Labs™Experimental Extruder

›Active Cooling Duct (installed)

›MakerBot®Replicator®Z18 Swivel Clip

(installed)

›Extruder Top Cap

UPON UNBOXING YOUR EXPERIMENTAL EXTRUDER PACKAGE, YOU SHOULD

HAVE THE FOLLOWING COMPONENTS:

›Two Nozzle Wrenches

›0.4 mm Brass Nozzle (installed)

›0.6 mm Brass Nozzle

›0.8 mm Brass Nozzle

›0.6 mm Stainless Steel Nozzle

BEFORE YOU START:

Download and 3D print the Experimental Extruder Jig using your standard PLA configuration for a steady base

during Nozzle changing. (thingiverse.com/thing:2557034)

MAKERBOT REPLICATOR+, MINI+

REPLICATOR (5TH GEN), MINI 3D PRINTERS:

MAKERBOT REPLICATOR

Z18 3D PRINTER:

PAGE 2EXPERIMENTAL EXTRUDER CONFIGURATION AND NOZZLE CHANGING GUIDE

STEP THREE:

Wearing heat resistant gloves

remove the hot Experimental

Extruder from the 3D printer

carriage and place into the

Experimental Extruder Jig.

STEP FOUR:

Use the large side of one

Nozzle Wrench to grasp the

flats on the thermal core cone

(adjacent to the Nozzle).

STEP TWO:

Attach the Experimental Extruder

to the carriage of your MakerBot

3D printer and run the

Preheat function.

PRO TIPS:

Some materials may cling to the

Nozzle, to avoid this load and then

unload MakerBot PLA filament to

purge the Nozzle.

Once hot, you may want to scrape any

caked filament off of the Nozzle using

forceps or another tool.

CAU T IO N :

Always wear heat resistant gloves

and protective eyewear when

handling a hot Nozzle.

PAGE 3EXPERIMENTAL EXTRUDER CONFIGURATION AND NOZZLE CHANGING GUIDE

STEP SIX:

Loosen the Nozzle with the two

Nozzle Wrenches but do not

completely remove — allow the

Nozzle to cool.

STEP SEVEN:

Once the loosened Nozzle has

cooled, remove it completely,

then screw on the replacement

Nozzle of choice and

hand-tighten.

STEP FIVE:

Use the small side of the

second Nozzle Wrench to grasp

the Nozzle.

PAGE 4EXPERIMENTAL EXTRUDER CONFIGURATION AND NOZZLE CHANGING GUIDE

STEP NINE:

Reattach the Experimental

Extruder to the 3D printer’s

carriage and run the Z-Calibrate

function. You are now ready

to load you 1.75 mm diameter

filament of choice

and print.

STEP EIGHT:

Heat the Experimental Extruder

on your 3D printer using the

Preheat function, then place the

Experimental Extruder back into

the Experimental Extruder Jig and

wrench tighten the Nozzle one

additional 40° turn.

PAGE 5EXPERIMENTAL EXTRUDER CONFIGURATION AND NOZZLE CHANGING GUIDE

For additional resources and

up-to-date information, visit

MakerBot.com/Labs

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali MakerBot Stampante 3D

MakerBot

MakerBot Replicator Z18 Manuale utente

MakerBot

MakerBot Replicator Manuale utente

MakerBot

MakerBot Replicator+ Manuale utente

MakerBot

MakerBot Replicator+ Guida

MakerBot

MakerBot Replicator Mini Compact Manuale utente

MakerBot

MakerBot Replicator Mini Manuale utente

MakerBot

MakerBot Replicator 2X Guida

MakerBot

MakerBot Replicator 2 Manuale utente

MakerBot

MakerBot Replicator 2X Manuale utente

MakerBot

MakerBot Replicator Mini+ Manuale utente

MakerBot

MakerBot Replicator Z18 Manuale utente

MakerBot

MakerBot Replicator 2 Manuale utente

MakerBot

MakerBot Replicator Mini Compact Manuale utente

MakerBot

MakerBot Replicator 2X Manuale utente

MakerBot

MakerBot Replicator Manuale utente

MakerBot

MakerBot Replicator 2 Manuale utente

MakerBot

MakerBot Replicator 2X Manuale utente

MakerBot

MakerBot Replicator Z18 Manuale utente

MakerBot

MakerBot Replicator 2X Manuale utente

MakerBot

MakerBot Replicator+ Manuale utente

MakerBot

MakerBot Replicator 2 Guida

MakerBot

MakerBot Replicator Manuale utente

MakerBot

MakerBot Replicator Mini+ Manuale utente

MakerBot

MakerBot Replicator Z18 Manuale utente

Manuali Stampante 3D popolari di altre marche

Ultimaker

Ultimaker S5 Material Station Manuale utente

EcubMaker

EcubMaker TOYDIY Manuale utente

AnyCubic

AnyCubic Kossel Plus Manuale utente

ReDeTec

ReDeTec ProtoCycler Manuale utente

Kywoo3D

Kywoo3D Tycoon IDEX Manuale utente

CraftBot

CraftBot PLUS PRO Manuale utente

3DGence

3DGence INDUSTRY F340 Manuale utente

HP Jet Fusion 4200 Istruzioni operative

Rokit

Rokit AEP Series Manuale utente

AnkerMake

AnkerMake M5 Manuale utente

DIYElectronics

DIYElectronics PRUSA I3 Istruzioni per il montaggio

Ackuretta

Ackuretta FreeShape 120 Manuale utente

LONGER

LONGER LK5Pro Manuale utente

Stratasys

Stratasys J850 Manuale utente

Stratasys

Stratasys FDM Vantage Series Manuale utente

ZYYX

ZYYX Pro II Manuale utente

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Guida utente

LONGER

LONGER LK4 Pro Manuale utente