Marinco SPL-12W Manuale utente

502-2 & 503-2 instructions

Instructions

marinco.com

Installing and Using the

Precision Spotlight

IMPORTANT!

READ THESE INSTRUCTIONS BEFORE INSTALLING AND USING THIS PRODUCT.

The Marinco Precision spotlight uses a super bright 100 Watt, replaceable H3 Halogen bulb

that produces a rich yet intense beam that can illuminate objects up to 1,000 ft away. It is

IP56 Weatherproof rated for extreme enironments, with a UV weather resistant housing and

fully enclosed tilt function driven by quiet motors that can withstand extreme temperatures

(5°F to 113°F or -15°C to 45°C). It has been designed and tested to withstand the harsh

marine environments including high humidity, salt water spray, shock, and vibration.

Innovative construction allows for upside down mounting and reverse motion programming.

Precision circuitry allows for remarkable aiming and tracking with two speed choices.The

spotlight has a 30 minute shut-down timer. If the spotlight is left unattended for more than

30 minutes, the spotlight will turn off. The shut-down has no effect on the SOS function of

the spotlight.

The Precision remotes have glow in the dark buttons and include one touch Automatic

Sweep and SOS options.The wireless remotes transmit a signal up too 200ft (60m). While

the spotlight comes with a wireless bridge remote there are two more optional remotes:

a wireless handheld remote w/lanyard (SPLR-1) and a hard wired bridge mount remote

(SPLR-3).

Package Includes:

• Spotlight with 12 Volt bulb installed

• Mounting bracket (no fasteners included)

• Wireless Bridge Remote (SPLR-2)

• Instruction manual

• Additional 24 Volt bulb**

**(models SPL-12W, SPL-12B, SPL-12C only)

MODELS: SPL-12W, SPL-12B, SPL-12C

SPLR-2 (included)

SPLR-1

SPLR-3

Español................................. 8

Français.............................. 16

Precision Spotlight Instructions

Required for Installation:

• Four (4) No. 10 stainless steel pan head screws for spotlight bracket

(Length and type of screws to be determined by mounting surface)

• Two (2) No. 6 stainless steel pan head screws

(Length and type of screws to be determined by mounting surface)

• Two (2) #16 AWG butt wire connectors

!WARNING IF THE APPLICATION IS 24 VOLTS, THE 12 VOLT BULB WILL NEED TO BE

REPLACED WITH THE 24 VOLT BULB. TO REPLACE THE BULB REFER TO THE BULB

REPLACEMENT SECTION. (PAGE 5).

Failure to use the appropriate bulb wattage will damage the spotlight.

!WARNING BEFORE OPERATION REMOVE BLUE FILM FROM LENS. FAILURE TO

REMOVE FILM WILL DAMAGE THE SPOTLIGHT.

Mounting and wiring of the Precision Spotlight

1. Select a ﬂat surface to mount the spotlight. Make sure there are no obstructions around

the spotlight that could interfere with the rotation (template included with light). Be sure

you will have wiring access to the underside of the chosen location and that drilling holes

will not damage existing wiring or structures. Avoid locations where lines, anchors and

sails might entangle or damage the light.

2. Refer to the template for mounting and wire hole location.

3. While installing the mounting bracket make sure that the securing screw is opposite the

direction that the light will be facing. Mark the mounting holes and center wire hole. Be

sure that there is at least a 6" (145 mm) radius of clearance from the center hole. See

dotted line on ﬁgure 1 (page 7).

4. Drill hole sizes appropriate for the type of screws or bolts being used. Note: the maximum

bracket hole sizes are No. 10 screws.

5. Drill the appropriate hole size to accommodate the wires. This will depend on the type of

wire being used.

6. The spotlight requires 12 or 24 volt power supplied through appropriate gauge wire.

(Note: If the wired bridge remote version is used, then 2 additional wires will need to

be routed from the remote to the spotlight.)

!WARNING CORRECT WIRE SIZE FOR THE RUN AND PROPER CIRCUIT PROTECTION

NEEDS TO BE SELECTED BASED ON ABYC STANDARDS. FAILURE TO FOLLOW

ABYC STANDARDS MIGHT LEAD TO SEVERE INJURY, DEATH OR DAMAGE

TO VESSEL.

7. Mount the mounting bracket after applying a small amount of non silicone sealant to the

area the screws or bolts penetrate the mounting surface. (Note: mounting bracket screw

heads should not protrude more than 0.2" (5 mm) above mounting bracket.)

8. Connect wires to spotlight using butt connectors. Red wire is positive, Black wire is

negative.

!WARNING POLARITY OF THE WIRES NEEDS TO BE CORRECT TO OPERATE THE

SPOTLIGHT! FAILURE TO WIRE CORRECTLY WILL DAMAGE THE SPOTLIGHT SYSTEM!

9. Slide spotlight over mounting bracket making sure the wires are not pinched and the

two holding tabs engage the light in the proper location. Align the securing screw hole

in the back of the spotlight base with the securing screw hole in the mounting bracket.

This will require a degree of pressure and effort as the mounting seal must be suitably

compressed during this process. For easier alignment, slightly lift the back side of the

Precision Spotlight Instructions

spotlight (containing the securing screw hole)

while depressing the gasket on the front side of the

spotlight (opposite the securing screw hole). Insert

securing screw and ensure that it is fully

engaged and secure.

!WARNING YOU MUST FEEL THE SCREW REACH

A TWISTING TORQUE TO KNOW THAT IT IS

PROPERLY ENGAGED

Note: In the photograph, the purple and yellow control

wires are shown for the wired-remote. If a wireless bridge remote is used, then the purple

and yellow leads are not necessary and can be tucked away within the spotlight base

Mounting the wired and wireless bridge remote

1. The remotes are all IP54 weather resistant.

2. Please choose a mounting location based on the gasket supplied with the remote (large

hole should be towards top)

3. Drill holes the correct size for the mounting screws.The holes through the remotes are

sized for a No. 6 pan head screw. The length and thread type will need to be determined

by the application. Remove and set aside the 2 screw covers.

4. Drill hole for the wiring. Note that the hole needs to be 5/8" to allow the unit to sit ﬂat.

5. If mounting the wireless bridge remote it will require a 12V or 24V power source.

If mounting the hard wired bridge remote then it does not need a local power source

and instead uses the purple and yellow wires connecting from the spotlight to the

remote. These two wires will supply the remote with power and control the spotlight.The

terminals on the remote can handle a 16 AWG to 26 AWG wire. Maximum torque on the

terminals is 2.21 in lbs (.25 nm).

6. Feed wires through drilled surface hole and gasket from below.

7. For the wireless bridge remote attach the power source wires to the remote (+) positive

and (-) negative terminals. For the hard wired bridge remote attach the 2 wires from

the

spotlight. The yellow wire needs to connect to the (+) positive and the purple wire needs to

connect to the (–) negative. Maximum torque on the terminals is 2.21 in lbs (.25 nm)

8. Place remote in desired location, align holes and tighten down.

9. Apply screw covers to remote to hide screws.

Pairing of wireless bridge and hand held wireless remote to spotlight

1. Disconnect all power to the spotlight.

2. Apply power to wireless remote. Press and hold the power button on the wireless remote.

3. While pressing the power button connect power to the spotlight.

4. After a few seconds you will hear the relay click and the light will turn on.

5. When the light turns on the paring is complete, release power button.

Paring multiple spotlights with separate remotes

If multiple spotlights will be within 200’ of one another and you want to control each spotlight

with independent remotes, please follow the instructions below.

1. For 1st spotlight, follow the “Pairing of wireless bridge and hand held wireless remote to

spotlight” instructions above.

2. For 2nd spotlight, follow instructions above except press and hold the power button AND

the UP button while inserting the battery in an SPLR-1 remote or connecting power to an

SPLR-2 remote.

3. For 3rd spotlight, follow instructions above except press and hold the power button AND

the RIGHT button while inserting the battery in an SPLR-1 remote or connecting power to

an SPLR-2 remote.

Precision Spotlight Instructions

4. For 4th spotlight, follow instructions above except press and hold the power button AND

the DOWN button while inserting the battery in an SPLR-1 remote or connecting power

to an SPLR-2 remote.

5. For 5th spotlight, follow instructions above except press and hold the power button AND

the LEFT button while inserting the battery in an SPLR-1 remote or connecting power to

an SPLR-2 remote.

Programming the remote when mounting the spotlight upside down

NOTE: This procedure reverses the directional buttons on the remote.

1. Pairing of the remote described above must be completed ﬁrst.

2. Disconnect all power to the spotlight.

3. Hold down the tilt UP and DOWN buttons on the remote.

4. While pressing the 2 buttons apply power to the spotlight and continue to hold down the

buttons for a few seconds until the spotlight tilts up or down.

5. The spotlight is now conﬁgured for inverted mode. Release buttons.

6. To return the spotlight to the standard conﬁguration repeat steps above.

!WARNING BEFORE OPERATION REMOVE BLUE FILM FROM LENS

Operation

SOS

(· · · — — — · · ·)

Pressing this button the light will begin

to signal the Morse code distress signal.

Press again to turn off.

Power on/off

Speed Control

Pressing this button will allow

you to change speed of the light,

SOS, and Sweep Angle function.

Auto Sweep

When this button is pressed

the light will begin to sweep left

and right at 90° for slow speed

and 70° for high speed. Press

the button again or a directional

button to stop the sweep.

Precision Spotlight Instructions

BULB REPLACEMENT CAUTION! AVOID

TOUCHING THE GLASS SURFACE OF

THE NEW BULB. (TOOLS REQUIRED:

MEDIUM PHILLIPS SCREWDRIVER AND

SMALL FLATHEAD SCREWDRIVER)

1. Remove 2 screws on bottom of lens

bezel.

2. Remove the bezel by inserting a small

ﬂathead screwdriver into the two

locations circled. Gently separate the

bezel from the body at both locations

using a straight separating motion until

you feel the bezel release from the lens.

3. Remove 6 screws from around the lens.

4. Remove lens and reﬂector as an

assembly.

5. Remove the screw holding the metal

grounding bar behind the reﬂector.

Remove the bulb assembly by pushing

on the bulb so it exits the back of the

reﬂector.

6. Unplug bulb and replace with new bulb.

(or 24 volt bulb if installation requires).

DO NOT TOUCH THE GLASS

SURFACE OF THE BULB. During

reassembly, hand tighten all screws until

snug. Do not overtighten or use a power

driver as doing so may strip the threaded

screw bosses.

Precision Spotlight Instructions

Description Color Item # OEM #

12/24 Volt, 100 Watt white SPL-12W —

12/24 Volt, 100 Watt black SPL-12B —

12/24 Volt, 100 Watt chrome SPL-12C —

12 Volt, 100 Watt white — SPL-12W.OEM

12 Volt, 100 Watt black — SPL-12B.OEM

12 Volt, 100 Watt chrome — SPL-12C.OEM

24 Volt, 100 Watt white — SPL-24W.OEM

24 Volt, 100 Watt black — SPL-24B.OEM

24 Volt, 100 Watt chrome — SPL-24C.OEM

Remote Speciﬁcations

Included *

Wireless Bridge Remote

(SPLR-2)

(Optional) †

Hand Held Bridge Remote

(SPLR-1)

(Optional) s

Wired Bridge Remote

(SPLR-3)

Power 12 or 24 Volt

(hard wired to power) CR2450 button

cell battery 12 or 24 Volt

(hard wired to spotlight)

Current draw

(idle / in use) negligible negligible negligible

Wireless range 200 ft (65m) 200 ft (65m) —

Estimated

battery life — > 40 hours

(continuous use) —

Dimensions 3.5"W x 2.25"H x .75"D

88mm x 57mm x 19mm

2.0"W x 3.78"H x 1"D

51mm x 96mm x 25mm

3.5"W x 2.25"H x .75"D

88mm x 57mm x 19mm

Weight 2.12 oz. (60g) 2.82 oz. (80g) 2.12 oz. (60g)

Housing material UV resistant PC/ASA UV resistant PC/ASA UV resistant PC/ASA

Button material Silicone (glow in the dark) Silicone (glow in the dark) Silicone (glow in the dark)

Wire 16AWG — 24AWG

Operating

temp range 5°F to 113°F (-15°C to 45°C) 5°F to 113°F (-15°C to 45°C) 5°F to 113°F (-15°C to 45°C)

IP Rating IP54 IP56 IP54

* There is no wiring required from the spotlight to the bridge remote. The spotlight and the bridge remote must be wired locally to power.

†

The hand held bridge remote includes a wrist lanyard and a surface mount cradle.

s The wired bridge remote requires hard wiring of 2 leads from the spotlight to the bridge.

Replacement Parts

202319 12V, H3 halogen replacement bulb

202320 24V, H3 halogen replacement bulb

SPLR-1 Spotlight remote, wireless hand-held

SPLR-2 Spotlight remote, wireless bridge mount

SPLR-3 Spotlight remote, wired bridge mount

Bulb 100 Watt, H3 Halogen (replaceable)

(12 Volt installed / 24 Volt included)

Power

(Input voltage) 12 Volt or 24 Volt

(note: must match bulb with voltage)

Current draw

(idle / in use) 0.03 Amps / 7.0 Amps

Peak beam

intensity 210,000 cp

Peak beam

distance 917 ft (280 m)

Lux @ 66' (20m) 525 Lux

Coverage at 66'

(20 m)

132 sq Ft

(12 sq m)

Rotatation 370° (built in limit stops)

Tilt 120° Tilt (75°◦up and 45° down)

Wireless range 200 ft (65m)

Dimensions 7.5"W x 7.5"H x 9.25"D

(19cm x19cm x 23.5cm)

Weight 3.30 lbs (1.5 kg)

Housing material UV resistant PC/ASA

Lens material UV resistant Lexan®

Wire type 16 AWG power

24 AWG control

Operating

temp range 5°F to 113°F (-15°C to 45°C)

IP Rating IP56

Tested in accordance with ANSI/NEMA standard FL1

Speciﬁcations

Precision Spotlight Instructions

FRONT

HOLDING

TABS

[ 55mm ]

32"

[ 24 mm ]

16 "

[ 58 mm ]

32"

[ 35mm ]

[ Ø286 mm ]

11 "

ROTATIONAL

CLEARANCE

[ Ø158 mm ]

6"SECURING

SCREW

MOUNTING

BRACKET

FIGURE 1

74.0

[2.91]

15.0

[0.59]

47.0

[1.85]

n15.9

(5/8" drill)

[0.63]

28.5

REF

[1.12]

57.0

REF

[2.24]

88.0

REF

[3.46]

Screw hole diameter

to suit mounitng screw.

Gasket outline

502-2 & 503-2 instructions

Instrucciones

marinco.com

Instalación y uso

del reﬂector Precision

¡IMPORTANTE!

LEA ESTAS INSTRUCCIONES ANTES DE INSTALAR Y USAR ESTE PRODUCTO.

El reﬂector Precision de Marinco usa una bombilla súper brillante y reemplazable de 100

vatios y Halógeno H3, que produce un haz de luz brillante e intenso que puede iluminar

objetos que están a distancias de hasta 300 m. Está clasiﬁcado como resistente a la

intemperie IP56 para ambientes extremos, con una carcasa resistente a la intemperie y

a los rayos UV, e incluye una función de inclinación accionada por motores silenciosos

que pueden soportar temperaturas extremas (entre -15 °C hasta 45 °C). El reﬂector ha

sido diseñado y probado para soportar rigurosos ambientes marinos que incluyen mucha

humedad, agua salada pulverizada, impactos y vibraciones. Su innovadora construcción

permite que se monte boca abajo y que se programen movimientos inversos. Sus circuitos

de precisión le conceden una extraordinaria puntería y rastreo con dos opciones de

velocidad. El reﬂector tiene un temporizador de apagado de 30 minutos. Si el reﬂector se

deja sin supervisión durante más de 30 minutos, se apagará. El apagado no tiene efecto en

la función de SOS del reﬂector.

Los controles remotos Precision tienen botones fosforescentes e incluyen opciones de un

solo toque de barrido automático y de SOS. Los controles remotos inalámbricos transmiten

una señal de hasta 60 m. Cuando el reﬂector incluye un control remoto puente inalámbrico,

hay dos controles remotos adicionales: un control remoto inalámbrico portátil con acollador

(SPLR-1) y un control remoto de montaje puente conectado por cableado permanente

(SPLR-3).

MODELOS: SPL-12W, SPL-12B, SPL-12C

SPLR-2 (Incluido)

SPLR-1

SPLR-3

El reﬂector Precision Instrucciones

El paquete incluye:

• Reﬂector con una bombilla

de 12 voltios instalada

• Soporte de montaje (no se incluyen

de sujeción)

• Manual de instrucciones

• Control remoto puente inalámbrico

(SPLR-2)

• Bombilla de 24 voltios adicional**

**(solo en los modelos SPL-12W, SPL-12B, SPL-12C)

Para la instalación se necesita:

• Cuatro (4) tornillos de cabeza troncocónica de acero inoxidable n.° 10 para el soporte del

reﬂector (la longitud y el tipo de los tornillos lo determinará la superﬁcie de montaje)

• Dos (2) tornillos de cabeza troncocónica de acero inoxidable n.° 6 (la longitud y el tipo de

los tornillos lo determinará la superﬁcie de montaje)

• Dos (2) conectores a tope para cables AWG n.° 16

ADVERTENCIA SI LA APLICACIÓN ES DE 24 VOLTIOS, SE NECESITARÁ CAMBIAR LA

BOMBILLA DE 12 VOLTIOS POR LA DE 24 VOLTIOS. PARA REEMPLAZAR LA BOMBILLA,

CONSULTE LA SECCIÓN DE REEMPLAZO DE LA BOMBILLA (PÁGINAS 13 Y 14).

Si no se usa el voltaje de bombilla adecuado, se dañará el reﬂector.

!ADVERTENCIA ANTES DEL FUNCIONAMIENTO, RETIRE LA PELÍCULA AZUL DE LA

CÁMARA. SI LA PELÍCULA NO SE RETIRA, SE DAÑARÁ EL REFLECTOR.

Montaje y cableado del reﬂector Precision

1. Seleccione una superﬁcie plana para montar el reﬂector. Asegúrese de que no haya

obstrucciones alrededor del reﬂector que puedan interferir con su rotación (plantilla

incluida con la luz). Asegúrese de que tendrá acceso de cableado en la parte inferior

de la ubicación seleccionada y que los oriﬁcios perforados no dañarán los cables o

estructuras existentes. Evite ubicaciones donde haya cuerdas, anclas y velas que

puedan enredar o dañar la luz.

2. Consulte la plantilla de la ubicación del montaje y el oriﬁcio para los cables.

3. Mientras instala el soporte de montaje, asegúrese de que el tornillo de ﬁjación esté en la

dirección opuesta a la de la luz que tendrá en frente. Marque los oriﬁcios de montaje y

el oriﬁcio central del cable. Asegúrese de que haya un radio de espacio de al menos 150

mm para el oriﬁcio central. Consulte la línea de puntos de la ﬁgura 1 (página 16).

4. Perfore oriﬁcios con el tamaño adecuado para el tipo de tornillos o pernos que se usarán.

Nota: el tamaño máximo de los oriﬁcios del soporte es para tornillos n.° 10.

5. Perfore un oriﬁcio del tamaño adecuado para dar cabida a los cables. Esto dependerá del

tipo de cable que se use.

6. El reﬂector necesita energía de 12 o 24 voltios suministrada a través de un cable de

calibre adecuado. (Nota: Si se usa la versión con control remoto puente conectado por

cableado, entonces se tendrán que tender 2 cables adicionales desde el control remoto

hacia el reﬂector).

!ADVERTENCIA EL TAMAÑO DE CABLE CORRECTO PARA EL FUNCIONAMIENTOY

PROTECCIÓN ADECUADA DEL CIRCUITO SE DEBE SELECCIONAR EN BASE A LAS

NORMAS ABYC. EL INCUMPLIMIENTO DE LAS NORMAS ABYC PUEDE PROVOCAR

LESIONES GRAVES, MUERTE O DAÑOS AL NAVÍO.

7. Monte el soporte de montaje después de aplicar una pequeña cantidad de sellador

que no sea de silicona en el área donde los tornillos o pernos penetran la superﬁcie de

montaje. (Nota: Las cabezas de los tornillos del soporte de montaje no deben sobresalir

de él por más de 5 mm).

El reﬂector Precision Instrucciones

8. Conecte los cables al reﬂector con conectores a tope. El cable rojo es positivo y el negro

es negativo.

!ADVERTENCIA ¡LA POLARIDAD DE LOS CABLES DEBE SER LA CORRECTA

PARA QUE EL REFLECTOR FUNCIONE! ¡SI LOS CABLES NO SE CONECTAN

CORRECTAMENTE EL SISTEMA DE REFLECTOR SE DAÑARÁ!

9. Deslice el reﬂector por sobre el soporte de montaje, asegurándose de que los cables

no estén comprimidos y de que las dos lengüetas sujetadoras acoplen la luz en el

lugar correcto. Alinee el oriﬁcio del tornillo de ﬁjación de la parte posterior de la base

del reﬂector con el oriﬁcio del tornillo de ﬁjación del soporte de montaje. Esto requerirá

un grado de presión y esfuerzo, ya que el sello de montaje debe ser comprimido

adecuadamente durante este proceso. Para una alineación más fácil, levante ligeramente

la parte posterior del reﬂector (que contiene el oriﬁcio del tornillo de ﬁjación) mientras

presiona la empaquetadura de la parte delantera del reﬂector (en la posición opuesta a

la del oriﬁcio del tornillo de ﬁjación). Inserte el tornillo de ﬁjación y asegúrese de que esté

completamente acoplado y ﬁjo.

!ADVERTENCIA DEBE SENTIR QUE EL TORNILLO

ALCANZA UN PAR TORSOR CUANDO ESTÁ

CORRECTAMENTE ACOPLADO.

Nota: En la fotografía se muestran los cables púrpura

y amarillo del control remoto para el control remoto

conectado por cableado. Si se usa un control remoto

puente inalámbrico, entonces los conductores púrpura

y amarillo no son necesarios y se pueden guardar

dentro de la base del reﬂector.

Montaje del control remoto puente conectado por cableado e inalámbrico

1. Todos los controles remotos tienen protección IP54, lo que los hace resistentes a la

intemperie.

2. Escoja una ubicación de montaje basada en la empaquetadura suministrada con el

control remoto (el oriﬁcio grande debe estar hacia la parte superior)

3. Perfore oriﬁcios del tamaño correcto para los tornillos de montaje. El tamaño de los

oriﬁcios en los controles remotos es para tornillos de cabeza troncocónica n.° 6. La

longitud y el tipo de rosca deberán determinarse según la aplicación. Retire y deje a un

lado las 2 cubiertas de los tornillos.

4. Perfore un oriﬁcio para el cableado. Tenga en cuenta que el oriﬁcio debe ser de 1,6 cm

para que la unidad pueda permanecer nivelada.

5. Si va a montar el control remoto puente inalámbrico, necesitará una fuente de

energía de 12 V o 24 V.

Si va a montar el control remoto puente conectado por cableado permanente, no

necesitará una fuente de energía local, y en su lugar, puede usar los cables púrpura

y amarillo que van desde el reﬂector hacia el control remoto. Estos dos cables le

proporcionarán energía al control remoto y controlarán el reﬂector. Los terminales del

control remoto admiten un cable de 16 AWG hasta 26 AWG. La torsión máxima de los

terminales es de 0,25 Nm.

6. Pase los cables a través del oriﬁcio perforado en la superﬁcie y la empaquetadura desde

abajo.

7. Para el control remoto puente inalámbrico, conecte los cables de la fuente de energía

a los terminales positivo (+) y negativo (-) del control remoto. Para el control remoto

puente conectado por cableado permanente, conecte los 2 cables del reﬂector. El

Altri manuali per SPL-12W

Questo manuale è adatto per i seguenti modelli

Indice

Lingue:

Altri manuali marinco Riflettore

marinco

marinco SPL-12W Guida

Manuali Riflettore popolari di altre marche

Guangzhou Yinhe Lighting&Sound Equipment Factory

Guangzhou Yinhe Lighting&Sound Equipment Factory NE-204 Manuale utente

LIVARNO home

LIVARNO home 375304 2101 Istruzioni originali

Cameo

Cameo CLQS40WW Manuale utente

Leviton

Leviton Ellipsoid 5/50 Manuale utente

Monacor

Monacor img Stage Line PARL-56PDX/CR Manuale utente

Vector

Vector SL3AKV Manuale utente

Quantum

Quantum Q262 Manuale operativo

Philips

Philips Vari-lite VL3015LT Manuale utente

EUROSPOT

EUROSPOT C51 Manuale utente

DTS

DTS MINI BRICK ARC Manuale utente

Federal Signal Corporation

Federal Signal Corporation VISIBEAM II Manuale

ACME

ACME LED-MS350B Manuale utente

EuroLite

EuroLite Akku flat light 1 Manuale utente

Commercial Electric

Commercial Electric SPTM-1401 Manuale utente

Vision & Control

Vision & Control SLB-500-W5K7-P-SL Manuale utente

Teknik

Teknik FLEXI Manuale utente

Craftsman

Craftsman CMXLSB10 Manuale utente

EuroLite

EuroLite LED SLS-144 UV Floor Spot Manuale utente

marinco SPL-12W Manuale utente

Manuali Riflettore popolari di altre marche