Marmitek X10 SS12E Manuale utente

S12

20472/20120530 • SS12E™

USER MANUAL

SS12E ™

TABLE OF CONTENTS

TABLE OF CONTENTS....................................................... 2

SAFETY WARNINGS ......................................................... 3

HOW DOES MARMITEK X10 WORK? ............................. 4

ADRESSES ......................................................................... 4

SIGNAL RANGE ................................................................ 5

INSTRUCTIONS FOR USE SS12™ WIRELESS SWITCH ...... 7

INTRODUCTION ............................................................... 7

PROPERTIES...................................................................... 7

CHANGE OF THE HOUSECODE........................................ 7

CHANGE OF THE UNITCODE ........................................... 8

CHANGE OF THE BATTERY.............................................. 8

APPLICATIONS ................................................................. 8

FREQENTLY ASKED QUESTIONS ..................................... 9

TECHNICAL DATA .......................................................... 10

DECLARATION OF CONFORMITY.................................. 11

COPYRIGHTS .................................................................. 12

SS12 3

SAFETY WARNINGS

•To prevent short circuits, this product should only be

used inside and only in dry spaces. Do not expose the

components to rain or moisture. Do not use the

product close to a bath, swimming pool etc.

•Do not expose the components of your systems to

extremely high temperatures or bright light sources.

•In case of improper usage or if you have altered and

repaired the product yourself, all guarantees expire.

Marmitek does not accept responsibility in the case of

improper usage of the product or when the product is

used for purposes other than specified. Marmitek

does not accept responsibility for additional damage

other than covered by the legal product

responsibility.

•This product is not a toy. Keep out of reach of

children.

•Do not open the product (battery panel excepted):

the device may contain live parts. The product should

only be repaired or serviced by a qualified expert.

•Keep batteries out of the reach of children. Dispose of

batteries as chemical waste. Never use old and new

batteries or different types of batteries together.

Remove the batteries when you are not using the

system for a longer period of time. Check the polarity

(+/-) of the batteries when inserting them in the

product. Wrong positioning can cause an explosion.

•Automatic switching devices provide comfort, but can

also be dangerous. They can surprise people or can

ignite clothing hanging over an electric heat source.

Please be careful and take appropriate measures to

avoid accidents.

HOW DOES MARMITEK X10 WORK?

Marmitek X10 components use the existing mains wiring

to communicate (using Marmitek X10 signals). You can

build a complete system using the three different kind of

components of the Marmitek X10 System:

1. Modules: These components will receive Marmitek X10

signals and will switch or dim the attached lamp or

appliance. Examples of these modules are lamp modules

and appliance modules. These are available as build-in,

micro, DIN rail and plug-in modules.

2. Controllers: These components will transmit Marmitek

X10 signals and thus will control the Modules.

3. Transmitters:Wireless components like remotes. The

signals of these components will be received by a

controller with transceiver functionality (IRRF 7243, TM13,

CM15Pro…..). The Transceiver will translate the signals into

Marmitek X10 signals on the power line.

ADRESSES

Up to a maximum of 256 different addresses can be preset.

These are subdivided into a so-called HouseCode (A to P

incl.) and a UnitCode (1 to 16 incl.). The HouseCode can

also be set on the controllers, so that the controllers and

modules become part of the same system. The address can

be set either using code dials or by pressing buttons,

depending on the type of module.

The Marmitek X10 System uses standard commands, which

control all units with the same HouseCode at the same

time (e.g. all lights on, all units off, etc.).

SS12 5

SIGNAL RANGE

Range of Marmitek X10 signals over the Power Line

and how to increase the range.

The Marmitek X10 System is based on power line

communication. The range of the Marmitek X10 signals

very much depends on the local circumstances. On average

the range is a cable length of 80 meters.

If you have difficulties with the range of your

Marmitek X10 signals, please pay attention to the

following facts:

1. When more than one phase is used for your electrical

system, it is necessary to couple these phases for the

Marmitek X10 signals. For coupling you can use FD10

Phase Couplers/Filters. You only need to install a Phase

Coupler/Filter when your wall outlets and light switches

are divided over more than one phase (more than one

group is no problem). For bigger buildings or longer

distances we advice you to use an active repeater instead

of passive FD10’s.

2. It is possible that Marmitek X10 signals are attenuated

by devices and lights which are connected to the power

line. In a normal home situation this effect is negligible

(the Marmitek X10 system is using active gain control to

eliminate the effects). However, it is possible that a

particular device in your house is attenuating the signals so

much that the range of Marmitek X10 signals is decreased

significantly. When you have range problems, it is wise to

try to locate the device which is attenuating the signals

simply by unplugging devices from the power line, and

testing the differences in range for your Marmitek system.

When e.g. your conclusion is that e.g. your computer

monitor is attenuating the signal, you can use a FM10

Plug-in Filter between the power line and the monitor to

eliminate the effects.

Known devices which can cause attenuation are:

PC Monitors

PCs with heavy internal power supplies

Old Televisions

Copiers

Fluorescent Lights

Gas Discharge Lamps (Energy Saving Lamps)

3. Some (old) devices are able to disturb the signal by

transmitting noise on the power line. Because the

Marmitek X10 signals are transmitted on 120 kHz, only

noise on or near this frequency will have influence on the

range. When you use a FM10 Filter to connect this device

to the power line, the noise will be filtered.

4. The Marmitek X10 protocol has several mechanism to

avoid modules to be switched on or off by other sources

than your Marmitek X10 Controllers. However, it is

possible that the Marmitek X10 signals are disturbed by

e.g. baby phones which are in TALK mode (continuous

transmission). When these kind of signals are present on

the power line it is possible that the Marmitek X10 signals

will not come through.

5. The mains do not stop at the front door of your home.

Everything that is attached to mains nearby your home can

have influence on Marmitek X10 signals (e.g. heavy

machinery). If you think that your system is influenced by

devices out of your house, it is advisable to install FD10

Phase Coupler/Filter on each phase entering the house.

These filters will block signals coming into or going out of

your house, but will also match the impedance for the

mains. Hereby make your house Marmitek X10 compatible

for these units. The FD10’s will not only filter but will also

couple the phases (please see 1).

SS12 7

INSTRUCTIONS FOR USE SS12™ WIRELESS SWITCH

INTRODUCTION

Congratulations buying the Marmitek X10 SS12 wireless

switch. This is a super thin, elegant wireless switch. It is the

ideal solution for situations where an extra switch is

needed without installing wires. It is to install on walls,

glass, doors tables etc. and transmits high frequent signals

through walls and ceilings. The SS12 wireless switch

transmits radio graphical signals to an X10 Transceiver

TM13, IRRF7243 or Marmitek X10 Alarm station. Then the

Transceiver or Station transmits these signals via the in

your house already installed electric wiring. Through this

you can switch on and off your lighting (or apparatus)

connected to X10 receivers (lighting can be dimmed also).

The SS12 is completely wireless and battery powered.

PROPERTIES

The switches are delivered standard at HouseCode A.

CHANGE OF THE HOUSECODE

1. Press the left button ON and keep it pressed. The red

LED flashes shortly. After 15 seconds the present set-

up is shown: 1 flash is HouseCode A, 2 flashes is

HouseCode B etc.

2. Release the button ON.

3. Now press shortly for the desired HouseCode on the

same ON button (1x = A, 2x = B etc). The LED flashes

every time you press the button.

4. At the last time keep the button pressed. After 3

seconds the LED shows the set-up HouseCode. Now

release the button.

CHANGE OF THE UNITCODE

When setting up the UnitCode the left button is set up in

the desired UnitCode. The right button is always

automatically one UnitCode higher.

1. Press the left OFF button and keep it pressed. The red

LED flashes shortly. After 15 seconds the present set

up is shown: 1 flash is UnitCode 1, 2 flashes is

UnitCode 2 etc.

2. Release the OFF button.

3. Now press shortly for the desired UnitCode on the

same OFF button (1x = 1; 2x = 2 etc.) The Led flashes

every time you press the button.

4. At the last time keep the button pressed. After 3

seconds the LED shows the set-up UnitCode. Now

release the button.

CHANGE OF THE BATTERY

Remove the right rocker switch at

the front of the SS12 and replace

the battery.

Use an identical 12V Alkaline

battery (type A23). Mind the

polarity when replacing.

APPLICATIONS

With the Marmitek X10 SS12 wireless switch you can

activate pre-programmed macros in the CM15Pro

computer interface.

You can also use the SS12 as a central operation panel for

your Marmitek installation.

SS12 9

FREQENTLY ASKED QUESTIONS

What is the reason for modules to switch on/off

spontaneously?

It is possible that a Marmitek X10 System is installed at one

of your neighbours using the same HouseCode. To solve

this problem try to change the HouseCode of your system,

or have FD10 Phase Coupler/Filter installed at your

incoming mains.

My modules will not respond to my controller.

Make sure that the HouseCode on all Modules and

Controllers are set to the same HouseCode (A .. P).

My modules will not react to my remote / sensor.

When you use a remote or sensor, you should have at least

one Transceiver or Marmitek Security Console installed in

your house. These components will translate the radio

signals to the Marmitek X10 signal on the power line. Only

one Transceiver should be installed for all remotes and

sensors set to the same House Code.

The other modules do not respond to signals of the

SS12. What can be the problem?

• Check if the SS12 has been set-up correctly. The easiest

way to do this is to give again the correct HouseCode to

the top left button.

• Has the battery been placed correctly?

• The SS12 uses a Transceiver module (TM13, IRRF7243 or

one of the Marmitek X10 alarm stations). Check if it works

properly, for instance to use another remote control.

• Maybe the range of the SS12 is not sufficient for your

purpose; if so, when using a TM13, place an extra TM13 in

the neighbourhood of your SS12.

Do you still have questions? Please check out

www.marmitek.com for more information.

TECHNICAL DATA

Supply: 1 x A23 12V Alkaline Battery

(supplied)

RF range: Up to 30m free field, up to 20m

through walls and ceilings

RF frequency: 433,92 MHz

RF power: 10mW

X10 Key codes: On, off, dim, bright

Ambient temperature: - 10° C to + 50° C (operation)

- 20° C to + 70° C (storage)

Dimensions: 80 x 80 x 20 mm

Environmental Information for Customers

in the European Union

European Directive 2002/96/EC requires that the

equipment bearing this symbol on the product

and/or its packaging must not be disposed of

with unsorted municipal waste. The symbol indicates that

this product should be disposed of separately from regular

household waste streams. It is your responsibility to

dispose of this and other electric and electronic equipment

via designated collection facilities appointed by the

government or local authorities. Correct disposal and

recycling will help prevent potential negative

consequences to the environment and human health. For

more detailed information about the disposal of your old

equipment, please contact your local authorities, waste

disposal service, or the shop where you purchased the

product.

Indice

Altri manuali Marmitek Interruttore

Marmitek

Marmitek Connect 421 UHD Manuale utente

Marmitek

Marmitek Connect 310 UHD 2.0 Manuale utente

Marmitek

Marmitek Connect TS41 Manuale utente

Marmitek

Marmitek SWM1P Manuale utente

Marmitek

Marmitek SS13 Manuale utente

Marmitek

Marmitek Connect 540 UHD Manuale utente

Marmitek

Marmitek Connect 720 Manuale utente

Marmitek

Marmitek SPEAKER ANYWHERE 350 Manuale utente

Marmitek

Marmitek Connect TS21 Manuale utente

Marmitek

Marmitek SPEAKER ANYWHERE 350 Manuale utente

Marmitek

Marmitek Connect 642 Pro Manuale utente

Marmitek

Marmitek CONNECT 421 Manuale utente

Marmitek

Marmitek SW10 Manuale utente

Marmitek

Marmitek Connect 621 UHD 2.0 Manuale utente

Marmitek

Marmitek Connect TS41 Manuale utente

Marmitek

Marmitek Connect 310 Manuale utente

Marmitek

Marmitek CONNECT 411 Manuale utente

Marmitek

Marmitek connect AE14 Manuale utente

Marmitek

Marmitek AD10 Manuale utente

Marmitek

Marmitek SW10 Manuale utente

Marmitek

Marmitek Connect 620 UHD 2.0 Manuale utente

Marmitek

Marmitek SWM1P Manuale utente

Marmitek

Marmitek 25008336 Manuale utente

Marmitek

Marmitek Connect TS21 Manuale utente

Manuali Interruttore popolari di altre marche

URC

URC Total Control MFS-8 Manuale utente

Azbil

Azbil HPQ-D11 Manuale utente

Sony

Sony DFS-900M Manuale utente

SICK

SICK i17S Manuale utente

F&F

F&F SZR-277 Manuale utente

Shure

Shure UAMS/BK Manuale utente

Dräger

Dräger X-zone Switch Off Manuale utente

Asco

Asco Joucomatic 349 Series Manuale utente

BT Mini Hub Manuale utente

D-Link

D-Link DES-1226G Manuale utente

Johnson Controls

Johnson Controls FS80-C Manuale utente

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuale utente

MicroNet

MicroNet SP1200A Manuale utente

Ruijie

Ruijie RG-PF2920 Series Manuale di installazione e funzionamento

Altinex

Altinex DA1914SX Manuale utente

MiLAN

MiLAN MIL-SM2401M Manuale utente

RJM

RJM MASTERMIND PBC/6X Manuale utente

Atlas

Atlas MMK-KVM8 Manuale utente