Marmitek MicroModule AWM2 Manuale utente

MicroModule

AWM2

Marmitek X10 transmitter for 2 addresses

with a built-in appliance module.

AWM2-201201

2MARMITEK

3 2 1

ENGLISH

1. Phase clamp (230V

2. Load clamp

3. Neutral clamps

4. Indicator light (LED

5. Set up button

6. Wire connections

to wall switches

DEUTSCH

1. Phase Anschlusspunkt

(230V

2. Anschlusspunkt

Schaltkabel

3. Nulklemmen

4. LED Anzeige

5. Programmierknopf

6. Anschlussdrähte

Schalter

NEDERLANDS

1. Fase aansluiting (230V

2. Aansluiting voor

belasting

3. Nulklemmen

4. LED indicator

5. Programmeerknopje

6. Aansluitdraden voor

schakelaars

MicroModule

AWM2

Marmitek MicroModule AWM2

Marmitek X10 transmitter for 2 addresses with a built-in

appliance module.

Applications

• The MicroModule can be installed behind conventional wall

switches or into wall outlets because of the extreme small size of

the MicroModule (minimum built-in depth 40 mm, advised 50

mm . The MicroModule is also ideal for installation into light

fixtures, home appliances or for use in areas with limited space

such as lowered ceilings.

• Universal compatibility: No limitation in choosing brand, color or

type of any wall switches and outlets.

• The MicroModule can be used in combination with regular

switches or pulse switches. These will be automatically recognized

by the AWM2.

• Install two-way switches without adding additional wires in

between wall switches (the MicroModules transmit their status to

the other MicroModuls through the power line .

• Execute Macro’s and preferred scenarios of a conventional switch

(e.g. along with Marmitek ActiveHome .

Functions

• X10 Transmitter for 2 Marmitek X10 addresses and the commands

ON and OFF.

• Built-in appliance module (16A .

• Two way Marmitek X10 communication.

• Two wall switches can be connected with one AWM2. One serves

the internal appliance module and also gives the X10 command

through the power line. The second wall switch is used to transmit

a second X10 address using the commands ON/OFF.

• Every Marmitek X10 controller can be used to program the

Marmitek X10 address through the power line (e.g. a Marmitek

Remote Control or the CM11 Computer interface .

• One free programmable Marmitek X10 address A1 to P16 (base

address . The second address programs automatically and will

always be the next Marmitek X10 address following on the

MICROMODULE AWM2 3

programmed address (e.g. Address A3 is programmed, the next

address will be automatically programmed as A4 .

• Input applicable for potential free switches (< +5V in regard to

neutral .

• Can respond to one or more group commands like ALL LIGHTS ON,

ALL UNITS OFF. These functions are disabled by default.

• The internal appliance module remembers its status after a main

voltage cut-off.

Color code wire connections

WARNING: THE WIRES OF THE MICROMODULE CARRY THE LIFE

DANGER 230V MAIN- VOLTAGE!! ALWAYS SWITCH OFF THE MAIN

MASTER SWITCH BEFORE INSTALLING THE MICROMODULE.

NOTE: THE BLUE WIRE (COMMON IS INTERNAL and DIRECTLY

CONNECTED TO THE NEUTRAL CLAMP (N .

Description of the Marmitek MicroModule wires

Blue: Neutral ( ) wire

Brown: Input 1, programmed base address + control of the

built-in appliance module

The built-in appliance module will switch from ON to OFF or vise

versa when the brown wire is connected with the blue wire. At the

same time the programmed address will transmit the new status of

the appliance module through the power line. Due to this Marmitek

X10 transmission you are able to switch other Marmitek X10 modules

(set to the same address . The new status will also be recognized by

other MicroModuls or e.g. the computer interface (activating

macro’s, status indication and more .

Red: Input 2, second address

When the red wire is connected to the blue wire, the programmed

4MARMITEK

"address +1" will be transmitted (e.g. when A3 is programmed as the

base address then the Marmitek X10 address A4 will be sent by using

input 2 . If the status in the MicroModule was ON, an OFF command

will be transmitted. If the status in the MicroModule was OFF, an ON

command will be transmitted. Through this transmission, other

Marmitek X10 modules can be switched remotely over the power line

or Macro’s setup in the computer interface can be activated.

Mounting Instructions

WARNING! ALWAYS SWITCH OFF THE MAIN MASTER SWITCH BEFORE

INSTALLING THE MICROMODULE.

To install the MicroModule AWM2 the following wiring is required at

the module installation point.

1. Neutral

2. Phase 23 V

3. Load. This wire runs

directly to the load.

• Take the wall switch out of the wall outlet.

• Disconnect all wires from the switch.

• Pull an additional Neutral-wire in case this one is missing.

MICROMODULE AWM2 5

• Connect the phase, neutralize and load wire to the terminals of

the MicroModule AWM2.

• Connect the thin wires of the built-in module to the wall switch.

Connect the blue wire to clamp P of the wall switch.

• Position the MicroModule against the back wall of the wall outlet

behind all the wires.

• You are now able to program the MicroModule. For more

information see chapter "Programming".

prog.

SAIX

prog.

SAIX

6MARMITEK

Red

Blue

Brown Phase 230V

Load

Neutral

• Install the wall switch at its original place after the MicroModule is

programmed.

Programming

WARNING: DO NOT FORGET TO TURN ON THE MAIN MASTER SWITCH

PRIOR TO PROGRAMMING.

Activate the setup mode.

The following steps have to be taken to start the setup procedure for

programming the MicroModule:

• Press the setup (prog. button for at least 3 seconds (see figure 5 .

The LED should stay on after releasing the setup button.

• Warning! The MicroModule will leave the setup mode if it doesn’t

receive any commands within 60 seconds.

Exit setup mode

• Press the setup button once shortly; The red LED will turn off now.

You can also wait for at least 60 seconds so that the MicroModule

will exit the setup mode automatically.

prog.

SAIX

prog.

SAIX

MICROMODULE AWM2 7

Activate or exit the setup mode.

Programming the X1 address and the various options

The chart below shows the various possibilities to program the

MicroModule AWM2

actory Programmable Command Light

defaults blinks

Address A1 Address A2 to P16 2x Address 2x

Doesn’t respond Responds to

to "All Lights On" "All Lights On" 2x "All lights on" 6x

Doesn’t respond Responds to

to "All Units Off" "All Units Off" 2x "All Units Off" 8x

prog.

SAIX

8MARMITEK

For programming the Marmitek X10 address and options you will be

able to use any Marmitek X10 controller or remote control. For the

following explanation we used a Marmitek 8-in-1 remote control to

program the preferred settings (When you use an RF remote control

like the Marmitek 8-in-1, then a TM13 Plug-in Transceiver is required

to convert the RF signals to the X10 commands on the power line .

Sample 1. Program the Marmitek X1 address E4:

• Setup your remote control (see manual 8-in-1 and the TM13

transceiver to house code E.

• Start with the MicroModule in setup mode.

• Press the Marmitek X10 button (marked with the symbol of a

house of the 8-in-1 remote control and then press button 4.

• Press the "ON" button 2x (= channel+ .

• The MicroModule responds by blinking the LED twice.

• The address E4 is programmed.

Sample 2. Program the function "All Units Off"

• Make sure you program the required Marmitek X10 address first!!

(e.g. E4 .

• Leave the remote control and the TM13 Transceiver on HouseCode

E or set it to the right HouseCode.

• Start with the MicroModule in setup mode.

• Press button marked with "All Units Off" 2x (= mute .

• The MicroModule responds by blinking the LED 8x.

NOTES:

• When you program the MicroModule, always program the address

first the optional function second.

• If the MicroModule receives a new address during setup mode, the

optional functions will be automatically reset to the factory

defaults.

MICROMODULE AWM2 9

Usage of the MicroModules in a 3 phase installation.

The X10 transmitters of the MicroModules transmit the command

only once for use in the phase of which they are connected. When

you want to receive the commands on your other phases as well, you

will need to install the CAT3000 phase coupler/repeater.

Technical specifications

Power 230V, 50Hz

Supply current < 30 mA capacitive

Appliance module 16 A

Signal transmission > 5Vpp in 5Ohm at 120 kHz ±1 kHz

according to EN50065-1, EN50065-2-1,

EN50065-4-1

X10 transmission 1 pulse burst at 0° and 180°

Signal sensitivity 25mVpp … 6Vpp at 120 kHz ± 4kHz

Signal to Noise ratio 1,35 : 1

Connections up to 2,5 mm2

Approvals NEN-EN-IEC 60669-2-1 and

NEN-EN-IEC 60669-2-2

Made in Holland

1 MARMITEK

Indice

Lingue:

Altri manuali Marmitek Trasmettitore

Marmitek

Marmitek SURROUND ANYWHERE 220 Manuale utente

Marmitek

Marmitek SM10 Manuale utente

Marmitek

Marmitek Stream S2 Pro Manuale utente

Marmitek

Marmitek CABLELINK 75 Manuale utente

Marmitek

Marmitek Audio Anywhere 625 Manuale utente

Marmitek

Marmitek Gigavideo 40 Manuale utente

Marmitek

Marmitek BOOMBOOM 55 Manuale utente

Marmitek

Marmitek Surround Anywhere 221 Manuale utente

Marmitek

Marmitek TWM4 Manuale utente

Marmitek

Marmitek GIGAVIDEO 70 Manuale utente

Marmitek

Marmitek SM10E Manuale utente

Marmitek

Marmitek Audio Anywhere 625 Manuale utente

Marmitek

Marmitek MicroModule TMA4 Manuale utente

Marmitek

Marmitek Stream S1 Pro Manuale utente

Marmitek

Marmitek MicroModule TMD4 X-10 Manuale utente

Marmitek

Marmitek Subwoofer Anywhere 640 Manuale utente

Marmitek

Marmitek BOOMBOOM 55 Manuale utente

Marmitek

Marmitek boomboom 50 Manuale utente

Marmitek

Marmitek MicroModule TMD4 Manuale utente

Marmitek

Marmitek boomboom 50 Manuale utente

Manuali Trasmettitore popolari di altre marche

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manuale del proprietario

Honeywell

Honeywell 5816WMBR Manuale utente

Kamstrup

Kamstrup READy MTU Istruzioni operative

Omega

Omega ZW Series Manuale utente

ABB

ABB Field 264H Guida

Alinco

Alinco DJ-V17T Manuale utente

Dejero

Dejero EnGo 3x Manuale utente

Rosemount

Rosemount 4600 Manuale utente

Speaka Professional

Speaka Professional 2342740 Manuale utente

trubomat

trubomat GAB 1000 Manuale utente

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manuale utente

Rondish

Rondish UT-11 Manuale utente

MG 10JRE Manuale utente

Burkert

Burkert 8177 Manuale utente

Firetide

Firetide HotPort 3203 Manuale

Tele Radio

Tele Radio T9-02 Manuale utente

Rotronic

Rotronic HygroFlex HF3 Series Manuale utente

Jamara

Jamara FCX6 Pro Tel Manuale utente