Martec VIPER DC Series Manuale utente
www.martecaustralia.com.au
VIPER DC Series Installation Guide
Thanks for choosing our VIPER DC Series ceiling fan.
We strongly recommend that you read this manual carefully before installation.
Models Parameters (Fan Only):-
MVDC133MMR 1320mm 3 Blade Ceiling Fan Matt Black with remote control
MVDC133WSR 1320mm 3 Blade Ceiling Fan White Satin with remote control
Models Parameters (Fan and Light):-
MVDC1333MMR 1320mm 3 Blade Ceiling Fan Matt Black, 18W Tricolour LED Light with remote control
MVDC1333WSR 1320mm 3 Blade Ceiling Fan White Satin, 18W Tricolour LED Light with remote control
Part List:
Qty 1x motor assembly Qty 1x instruction manual Qty 1x screw kit Qty 3x blades
Qty 1x balancing kit Qty 1x hanging bracket Qty 1x remote control kit
Application
Flat Surface / Ceiling Corrugated Ceiling Apex Ceiling
Slope Ceiling up to 15°
How to Assemble
Secure the hanger bracket
to ceiling beam or a suitable
piece of timber inserted
between the ceiling beams
using the two long screws
supplied with the package.
(See Fg.1)
Place circular shockproof
gasket above the hanger
bracket. Align the bracket
and screw the hanger
bracket to the ceiling tightly.
(See Fg.2)
Place fan into hanger
bracket and align Ball Joint
Slot with hanger bracket as
illustrated.(See Fg.3)
After wiring is completed,
attach the canopy to the
hanger bracket by pushing
upwards and twisting anti-
clockwise. Tighten screws
and ensure canopy is not
touching the ball joint.
(See Fg.4)
Fg.1 Fg.2 Fg.3 Fg.4
Ball seat
rubber
cover
(packed
with
hanger
bracket)
Anti-vibration
washer
www.martecaustralia.com.au
WARNING Installation MUST carry out by a qualied and licensed electrician.
How to Install Blades
How to Install / Remove the Cover
Connect the 2-pin
connectors from motor
housing with the light kit
plate.
Install the light kit plate
to the motor using screw
provided.
Slot the plastic cover into the
light kit. (See Fg.6)
Fg.6
CCT (Colour Changeable Temperature)
Fg.8
NB: Ensure the blades do not get damaged or bent during the
installation process while the fan maybe on the ground, this will aect
the performance and balance of the fan and this is NOT covered under
warranty.
Attach the blade to the top of the motor. Tighten and secure blade
with screws and washers provided. Repeat this procedure until all
blades are installed. (See Fg.5)
Fg.5
Install the shade cover into
the bottom of ceiling fan
(See Fg.7)
Fg.7Model shown with light Model shown fan only
Choose colour temperature by icking the switch in the
LED (See Fg.8)
C = 5000K cool white
N = 4000K neutral white
W = 3000K warm white
Dimming
The VIPER ceiling fan has a smart 3 step dimming LED light module which doesn’t require a dimmable remote control or a wall dimmer.
It only requires a remote control kit supplied with the product.
Turn the switch on and the light will turn on. Flick the switch on/o within 1 second and the light output will dim down to approx. 50%.
Flick the switch on/o again and the light output will dim down to approximately 15%. The light kit has memory function.
www.martecaustralia.com.au
WARNING Installation MUST carry out by a qualied and licensed electrician.
Instructions and Functions of Transmitter
1. LED indicator light
2. Light ON/OFF
(Use to dim light within 1s)
3. Speed of the fan
(1 high speed - 5 low speed)
4. Timing control of the fan
5. Direction of the fan (reverse
switch)
6. Fan ON/OFF
7. 12v battery to be used
in transmitter
NB: Remote shown fan and light NB: Remote shown fan only 1. LED indicator light
2. Speed of the fan
(1 high speed - 5 low speed)
3. Timing control of the fan
4. Direction of the fan (reverse
switch)
5. Fan ON/OFF
6. 12v battery to be used in
transmitter
Installing Receiver Remote Control
Pairing Instructions
• Turn “ON” the power supply and within 30 seconds
• Press and hold the transmitters “FAN ON/OFF” button for 5 seconds and a “beep” will be heard
• Pairing initial step must be performed within 30 seconds of power being turned on
i) ensure the isolation switch or power supply to the rst installed fan is turned o prior to pairing futher fans
ie. pair one fan at a time
ii) ensure isolation switch is kept to the ON position, the isolation switch is not to be used as a light switch as
this will damage and make the remote recevier inoperable
Important Reminders
• Receiver must be correctly installed in the mounting bracket
• When the transmitter cannot control the receiver, please check
i) has sucient battery in the transmitter
ii) any existence of similar remote controlled products nearby that cause interference
• Replace battery if getting low as this will aect sensitivity of the transmitter
• Take the battery out from the transmitter when leaving used for a long time to avoid battery leaks
• Support up to 200W lighting power
• Isolation switch MUST be connected in the line
• Dimming switch on the light models is operated by tuning the light ON/OFF button within 1s. Light output will dim in
stages from 18W to 9W to 3W approximately
www.martecaustralia.com.au
WARNING Installation MUST carry out by a qualied and licensed electrician.
Wire Connections
CARE INSTRUCTIONS
• Ensure the ceiling fan is disconnected before any cleaning or maintenance work is carry out.
• LED lights are not detachable nor replaceable. It can only be supplied with the ceiling fan as one unit.
WARNING
• Installation of fans MUST follow SAA standards and meet local authority regulations.
• Installation MUST be carried out by a qualied and licensed electrician.
• Fan and light MUST be earthed.
• Bracket MUST be rmly attached to a at solid structure or timber frame.
• DO NOT mix blades from one model to another, all blades MUST be replaced if damaged.
• The warranty is VOID if product is not installed according to this installation guide.
6* Year Warranty
Visit our website for details https://www.martecaustralia.com.au/warranty-statement/
NB: Remote Control fan and light NB: Remote Control fan only
Questo manuale è adatto per i seguenti modelli
4
Altri manuali Martec Fan
Martec
Martec Kingston MKDC124OB Manuale utente
Martec
Martec Flush AC Series Manuale utente
Martec
Martec Elite AC Series Manuale utente
Martec
Martec LE1342 Series Manuale utente
Martec
Martec MXFT25S Manuale utente
Martec
Martec Scorpion MSF133 Manuale utente
Martec
Martec Newport Series Manuale utente
Martec
Martec DLS1043 Manuale utente
Martec
Martec Lifestyle DC Series Manuale utente
Martec
Martec DISCOVERY II AC Series Manuale utente
Martec
Martec Norfolk DC Smart Series Manuale utente
Martec
Martec LINK AC Series Manuale utente
Martec
Martec Albatross Series Manuale utente
Martec
Martec IMPERIAL SERIES Manuale utente
Martec
Martec FOURSEASONS Link DC Series Manuale utente
Martec
Martec METRO DC Series Manuale utente
Martec
Martec Ariel Series Manuale utente
Martec
Martec LIFESTYLE MINI Manuale utente
Martec
Martec Governer Series Manuale utente
Martec
Martec SCORPION DC Series Manuale utente
