MASCOT RS-51B Manuale utente
RS-51B / RS-55B
RS-31B / RS-33B
USER’S MANUAL
WIRELESS MICROPHONE SYSTEM
Channel
Contents:
Introduction
Quick Start Guide
Product Description
System Operation
Color Label Identification
Trouble Shooting
Specification
-------------------------------------------------------------------------- 1
------------------------------------------------------------------ 2
---------------------------------------------------------------- 4
------------------------------------------------------------------ 10
--------------------------------------------------------- 13
------------------------------------------------------------------- 14
------------------------------------------------------------------------- 15
This device complies with part 15 of the FCC rules. Operation is subject to the following
two conditions:(1)This device may not cause harmful interference and (2) This device must
accept any
The changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no
change to the antenna or the device is permitted.
could result in the device exceeding the
to operate the device.
Thank you for purchasing our product. This PLL synthesized wireless microphone system
operates in UHF band frequency with 8 selectable channels. Please read this instruction
manual carefully before operating the system. This manual covers the function and operation
of the wireless microphone system.
Safety
Do not spill liquid on the appliance and do not drop it on a hard concrete floor.
Do not place the equipment near heat sources such as radiators, heating ducts, amplifier, etc.
Do not expose the equipment to direct sunlight, extremely dust, excessive moisture, rain,
mechanical vibrations, or shock.
Take out the battery from transmitter, if the appliance has been not used for a longer period.
This will avoid the damage resulting from a defective leaking battery.
WARNING: To reduce the risk of fire or electric shock, do not use the products near water
and do not expose them to rain or moisture.
Environment
When disposing the equipment, remove the batteries, separate the case, circuit boards,
and cables, and dispose of all components in accordance with local waste disposal rules.
Do not throw used batteries into a fire or garbage bin with domestic rubbish. Be sure to
dispose of used batteries in accordance with local waste disposal rules.
If the equipment is not going to be used for a long time, disconnect the AC adapter from
the power outlet. Please note that if you turn the equipment off while leaving the AC
adapter plugged in, it is not fully isolated from the power supply.
No guarantee claims for the equipment and no liability for any resulting personal damage
or material damage will be accepted if the equipment is used for other purpose than
originally intended, if the equipment is not correctly connected or operated, or if the
equipment is not repaired in an expert way.
Notice :
FCC Statement
interference received, including interference that may cause undesired operation.
Introduction
Any change to the antenna or the device
RF exposure requirements and void user’s authority
1
1. Connected Receiver Power Cable
2. Connect Mixer or Amplifier
2
Quick Start Guide
3. Insert Batteries
4. Select channel
3
Quick Start Guide
Front :
Rear :
RS-51B: Diversity Receiver
4
Receiver
1. Balanced XLR Audio Output
2. Unbalanced 6.35mm Audio Output
3. MIC/LINE Switch: Use this switch to adjust audio output level for MIC level (-20dB) or
LINE level (0dB).
4. Squelch: Turn the knob to adjust the noise floor level.
5. DC Input Jack
1. Power Button: Press and hold for 2 sec. to turn the power on. Press and hold for 2
sec. to turn the power off.
2. AF Indicator: The indicator glows to indicate that audio signal has been received.
3. RF Indicator: The indicator glows to indicate that RF signal has been received.
4. LED Display: The 7 segment LED display shows the selected preset channel.
5. Channel Selector: Press and hold for 1 sec. to select the operating channels.
6. Antenna: Fixed UHF antenna.
7. Volume Control: Adjust the receiver output level.
DC 12V 500mA
MIC
SQ
1 2
3
4 5 66 7
1 32 4 5
5
Front :
Rear :
RS-55B: Diversity Receiver
Receiver
1. Balanced XLR Audio Output
2. Unbalanced 6.35mm Audio Output
3. MIC/LINE Switch: Use this switch to adjust audio output level for MIC level (-20dB) or
LINE level (0dB).
4. Squelch: Turn the knob to adjust the noise floor level.
5. DC Input Jack
6. Mix Out: The audio output for CH A and CH B is mixed.
1. Power Button: Press and hold for 2 sec. to turn the power on. Press and hold for 2
sec. to turn the power off.
2. AF Indicator: The indicator glows to indicate that audio signal has been received.
3. RF Indicator: The indicator glows to indicate that RF signal has been received.
4. LED Display: The 7 segment LED display shows the selected preset channel.
5. Channel Selector: Press and hold for 1 sec. to select the operating channels.
6. Antenna: Fixed UHF antenna.
7. Volume Control: Adjust the receiver output level.
DC 12V 500mA
MIC
SQ
1 2 4 5 7 2 4 5 7
3 32 24 4 5
Front :
Rear :
RS-31B: Diversity Receiver
6
Receiver
1. Balanced XLR Audio Output
2. Unbalanced 6.35mm Audio Output
3. MIC/LINE Switch: Use this switch to adjust audio output level for MIC level (-20dB) or
LINE level (0dB).
4. Squelch: Turn the knob to adjust the noise floor level.
5. DC Input Jack
1. Power Button: Press and hold for 2 sec. to turn the power on. Press and hold for 2
sec. to turn the power off.
2. AF Indicator: The indicator glows to indicate that audio signal has been received.
3. RF Indicator: The indicator glows to indicate that RF signal has been received.
4. LED Display: The 7 segment LED display shows the selected preset channel.
5. Channel Selector: Press and hold for 0.5 sec. to select the operating channels.
6. Antenna: Fixed UHF antenna.
DC 12V 500mA
MIC
SQ
32 4 5
1 2 4 5 66
Front :
Rear :
RS-33B: Diversity Receiver
Receiver
7
1. Balanced XLR Audio Output
2. Unbalanced 6.35mm Audio Output
3. MIC/LINE Switch: Use this switch to adjust audio output level for MIC level (-20dB) or
LINE level (0dB).
4. Squelch: Turn the knob to adjust the noise floor level.
5. DC Input Jack
6. Mix Out: The audio output for CH A and CH B is mixed.
1. Power Button: Press and hold for 2 sec. to turn the power on. Press and hold for 2
sec. to turn the power off.
2. AF Indicator: The indicator glows to indicate that audio signal has been received.
3. RF Indicator: The indicator glows to indicate that RF signal has been received.
4. LED Display: The 7 segment LED display shows the selected preset channel.
5. Channel Selector: Press and hold for 0.5 sec. to select the operating channels.
6. Antenna: Fixed UHF antenna.
DC 12V 500mA
MIC
SQ
Channel
3 32 24 6 4 5
1 2 24 5 5 66
8
UF-31B Handheld Microphone
1. Grille: Protects the microphone capsule and helps reduce breath sounds and wind
noise.
2. Talk Switch: Slide up the switch to talk and slide down to mute.
3. Channel Selector: 8 different selectable channels.
4. Battery Compartment: Insert two AA batteries here and make sure that the polarity of
batteries is correct.
5. Power Button: Press and hold for 2 sec. to turn the power on or off.
6. Power LED: Indicate the power / low battery level status.
LED Indicator Status
Green Ready
Flashing Red Low battery / power when less than 10 minutes operation
Questo manuale è adatto per i seguenti modelli
3
Indice
Altri manuali MASCOT Sistema microfonico
Manuali Sistema microfonico popolari di altre marche
Sennheiser
Sennheiser Evolution Wireless Digital EW-DX EM 2 Manuale utente
Alpha Technologies
Alpha Technologies RBMS Manuale utente
SWIT Electronics Co.,LTD.
SWIT Electronics Co.,LTD. CW-S150 Manuale utente
Shure
Shure UA844 Manuale utente
Panasonic
Panasonic SHFX70 - DVD HOME THEATER WIRELESS SYSTEM Manuale utente
Pyle
Pyle PDWM5000 Manuale utente