Mastech MS8233A Manuale utente

Indice

Altri manuali Mastech Multimetro

Mastech

Mastech MS5203 Manuale utente

Mastech

Mastech MS8253 Series Manuale utente

Mastech

Mastech MS8269 Manuale utente

Mastech

Mastech MAS345 Istruzioni per il montaggio

Mastech

Mastech MAS830L Istruzioni per il montaggio

Mastech

Mastech m3900 Manuale utente

Mastech

Mastech MY-65 Manuale utente

Mastech

Mastech MS8228 Manuale utente

Mastech

Mastech MS8229 Manuale utente

Mastech

Mastech MS8228 Manuale utente

Mastech

Mastech CSIMS8264 Istruzioni per il montaggio

Mastech

Mastech MY67 Manuale utente

Mastech

Mastech MS8269 Manuale utente

Mastech

Mastech MS8251A Manuale utente

Mastech

Mastech MS8321B Manuale utente

Mastech

Mastech MS8238H Manuale utente

Mastech

Mastech MS2203 Manuale utente

Mastech

Mastech MY70 Manuale utente

Mastech

Mastech MY-60 Manuale utente

Mastech

Mastech MS8240B Manuale utente

Mastech

Mastech MS8218 Manuale utente

Mastech

Mastech MS2208 Manuale utente

Mastech

Mastech ms8217 Manuale utente

Mastech

Mastech MS2108A Manuale utente

Manuali Multimetro popolari di altre marche

Agilent Technologies

Agilent Technologies 34420A Manuale utente

Fluke

Fluke 83 Manuale utente

Hameg

Hameg HM 8012 Manuale utente

Steren

Steren MUL-300 Manuale utente

Somogyi Elektronic

Somogyi Elektronic home SMA 92 Manuale utente

Gossen MetraWatt

Gossen MetraWatt METRAmax 6 Manuale utente

PeakTech

PeakTech 4000 Manuale per l'uso e la cura

YOKOGAWA

YOKOGAWA 90050B Manuale utente

Gossen MetraWatt

Gossen MetraWatt METRALINE DMM16 Manuale utente

Fluke

Fluke 8846A Manuale operativo e di manutenzione

Tempo Communications

Tempo Communications MM200 Manuale utente

Elenco Electronics

Elenco Electronics CM-1555 Manuale utente

SDAR

SDAR 830A, 830B, 830D, 830C Manuale utente

RS PRO

RS PRO RS-9519BT Manuale utente

BGS technic

BGS technic 8890 Manuale utente

Amprobe

Amprobe Hexagon 60 Manuale utente

Morris

Morris 57074 Manuale utente

Agilent Technologies

Agilent Technologies 34450A 5 Digit Multimeter Manuale utente

CAT.II

600 V

AUTO MAX

04

1.SAFETY INFORMATION

This multimeter has been designed according to IEC61010-1

concerning electronic measuring instruments with an

overvoltage category (CAT II) and pollution 2.

Follow all safety and operating instructions to ensure that the

meter is used safely and is kept in good operating condition.

Full compliance with safety standards can be guaranteed only

with test leads supplied. If necessary, they must be replaced

with the type specified in this manual.

1.2Maintenance

• Before opening the case, always disconnect test leads

from all energized circuits.

• For continue protection against fire; replace fuse only

with the specified voltage and current ratings:

250mA/250V(Quick Acting)

10A/250V(Quick Acting)

• Never use the meter unless the back cover is in place

and fastened completely.

• Do not use abrasives or solvents on the meter. To clean

it using a damp cloth and mild detergent only

1.1Safety symbols

Important safety information, refer to the

operating manual.

Dangerous voltage may be present

Anti-garbage

Double insulation (Protection class II).

Fuse must be replaced with rating specified

in the manual.

03

1.3 During use

• Never exceed the protection limit values indicated in

specifications for each range of measurement.

• When the meter is linked to measurement circuit, do not

touch unused terminals.

• Never use the meter to measure voltages that might

exceed 600V above earth ground in category II

installations.

• When the value scale to be measured is unknown

beforehand, set the range selector at the highest

position.

• Before rotating the range selector to change functions,

disconnect test leads from the circuit under test.

• When carrying out measurements on TV or switching

power circuits always remember that there may be high

amplitude voltages pulses at test points, which can

damage the meter.

• Always is careful when working with voltages above 60V

dc or 30V ac rms. Keep fingers behind the probe barriers

when making voltage measurements with test leads.

• Never perform resistance measurements on live circuits