Master FVR600 Manuale utente
Henan Master Machinery Co., Ltd
Tel:(+86)17737606271 www.mastermachinerys.com
1
OPERATION MANUAL
FVR600 Vibratory Road Roller
P E R F O R M A N C E · E F F I C I E N T · R E L I A B L E
Henan Master Machinery Co., Ltd
Tel:(+86)17737606271 www.mastermachinerys.com
2
Master sincerely thanks you for selecting the Plate
Compactor Machine. For your Safety and proper operation,
before you start to operate or carry out any maintenance on
this equipment, YOU MUST READ and STUDY this manual
carefully. Be sure to always keep it ready for reference.
Produced By Henan Master Machinery Co.,Ltd
Dear Customer,
Thanks for choosing Master machine.
To ensure the safety and proper use of the machine,
please read the instruction book carefully before use.
Also, please fill this card and save it for warranty use.
Buyer Name
Purchase
Time
Tel
Contact
Person
Address
Product
Name
Road Roller
MODEL
FVR600
Motor Model
Note
1. Preface
Thank you very much that you have purchased the products.
This operation manual will tell you how to correctly operate and
Henan Master Machinery Co., Ltd
Tel:(+86)17737606271 www.mastermachinerys.com
3
maintain your machine. Before using the machine, please read the
operation manual thoroughly to guarantee the correct operation.
Following the operation requirements in the operation manual will make
that your machine is in the best operation state so as to extend the life
of the set. For you own safety and protection injury, carefully read,
understand and observe the safety instructions described in this
manual.
Keep this manual or a copy of it with the machine. This machine is built
with user safety in mind; however, it can present hazards if improperly
operate and serviced. Follow operating instructions carefully!
With the increasing improvement and enhance of the products made by
the company, there may be some differences between the contents
described in the operation manual and the practical products, it is our
desire that the users will pay attention to the differences.
The walk-behind double drums roller is light road roller. It is used to
compress on the asphalt, sand soil gravel and it is also used to planish
the lawn and playground.
This machine is with hydraulic unit, variable plunger pump, and
constant displacement hydraulic motor, which make the machine has
excellent performance.
2. Safety alerts
In order to operate the machine safely, it is very necessary to
maintain the machine regularly. Please read the Safety alerts carefully
Henan Master Machinery Co., Ltd
Tel:(+86)17737606271 www.mastermachinerys.com
4
to master the skills of maintenance and operation.
3. Driving qualification
Qualified staffs are allowed to operate the machine
1. Compaction task
Operator should get training on the aspects of compaction
before operating the machine.
2. Loading and unloading the machine
Operator should get training on the aspects of Loading and
unloading the machine
4. Safety precautions
4.1 General precautions
◎Read the Manual carefully to understand and master the
operating methods and functions, know the operation device and
meanings of labels.
◎Comply with the rules
◎Be familiar with the working site in advance.
◎Be familiar with the functions of the machine.
Please operate the machine within the allowed range.
◎Check the machine before operating. Make sure the functions
of the machine are sound.
◎Pay attention to the bystanders during working.
◎Do not touch fire components.
◎Pay attention to fireproof.
Fuel and oil catch fire easily, do not smoking and using match
and lighter. The engine should be turned off the engine before filling fuel
Henan Master Machinery Co., Ltd
Tel:(+86)17737606271 www.mastermachinerys.com
5
and far from open fire.
4.2 Preparations for safety operation
◎Cleaning the machine
◎Check the machine before operation. Make sure the functions
of the machine are sound.
Check and make sure the enough level of all the liquid.
Check and make sure no leaking of hydraulic oil, fuel and water.
4.3 Attentions before starting up engine
◎Make sure each control levers are in the neutral position
before starting up the engine. Using manual brake lever to stop the
engine.
◎Ensure safety around the machine before starting up engine.
◎Be care of ventilate.
It is danger to inhale the exhaust gas, ensure enough ventilate
during working.
◎Do not near exhaust pipe.
The exhaust gas is poisonous.
4.4 Attentions after starting up engine
◎Preheat the machine.
Idle the machine several minutes after starting up the engine. Do
not operate the machine in high speed at the beginning of
operating. Those will avoid damaging the machine, and prolong
the life of machine,
◎Trial run
Trial operate the machine and check if every function are sound.
4.5 Attentions during working
Henan Master Machinery Co., Ltd
Tel:(+86)17737606271 www.mastermachinerys.com
6
◎Avoid operation errors.
Focus on operation, and pay attention to bystanders.
◎Be careful of bystanders and barriers when forward and back
the machine.
◎Repair the machine at once when meeting shortcomings.
◎Attentions to park the machine.
The machine should be parked on level surface. If must be parked
on slope, block should be put in the front of drum.
Push the forward and back control lever to middle position, and
push the lock lever to lock position, then turn off the engine, and
pull out the key.
4.6 Attention of loading and unloading the machine
◎Use the hard climbing board with appropriate width, length
and thickness for safe loading and unloading
◎Don’t use redirector on the climbing board.
◎Use the rope with the adequate strength to lifting the machine
◎Please vertical lifting the machine
◎After loading, the machine firmly fixed. Then inset the block
under the double side of drums
4.7 The correct usage of the battery (note: For the battery needing to
maintain, maintenance-free except)
◎The battery will produce flammable gas, may cause an
explosion. Do not smoke around the battery, so that the battery can be
far away from fire, sparks and fire
Battery electrolyte contains sulfuric acid; it will destroy the clothing
and skin. If it exposed to clothes and skin, rinse with plenty of
Henan Master Machinery Co., Ltd
Tel:(+86)17737606271 www.mastermachinerys.com
7
water. In case of contact with eyes, rinse with water and seek for
medical help.
◎During checking and processing the battery, please turn off
the engine and turn the switch to the OFF position
◎Ensure the wire ends tighten
Battery liquid under the minimum line, please don’t charge. If you
continue to use the battery at this time, it will shorten the battery
life, or even cause an explosion. Should add distilled water
immediately to the right charge location.
4.8 Attention of the maintenance
◎Keep the machine clean
◎Detach the negative pole of the battery to disconnect the
power when repairing the electric system or doing the electric welding.
◎Attention of operating the high-pressure pipe
In the “OFF” position, the key can pulled out. All electronic systems are
shut down. The key to “OFF” position can turn off the engine. Or the
battery power on their own, and led to the engine fails to start.
◎Throttle switch
Used to control the engine speed
Press down the “throttle switch”, the engine speed will increase. Lift up
the “throttle switch”, the engine speed will decrease to stop
Attention: When starting the engine, should press down the
“throttle switch” to the suitable position (full throttle)
◎Lock spanner
Can be folded during transportation (see the overall structure)
1) When folding, pull back the “lock spanner” until the position locked
automatically.
Henan Master Machinery Co., Ltd
Tel:(+86)17737606271 www.mastermachinerys.com
8
2) When normal running, have to unfold the tail parts. Pull back the
“lock spanner” to the run position, and then the “lock spanner” is
automatically locked,
◎Manual lock lever
When machine stops, put the “manual lock lever” in the locked position.
When machine runs, unlock the “manual lock lever”.
Attention: Machine stops, must lock the “manual lock lever”!
Machine starts, must unlock the “manual lock lever”!
5.2 Diving operation
5.2.1 Inspection before operation
Ensure that the “forward and backward handle” in the middle
position, vibration switch is in the “OFF” position. “Manual lock lever”
locks the machine
5.2.2 Start up the engine
1) Turn on the throttle lever (full throttle)
2) Starting switch turn to “start” position, to start the engine. At the
same time of engine start, release the hand, the key will return to the
“ON” position.
Attention: Do not keep starting more than 15 seconds
If the starting fails, starting again wait for 30 seconds!
Excessive use the starter, will burn the starting motor!
Overall structure
Henan Master Machinery Co., Ltd
Tel:(+86)17737606271 www.mastermachinerys.com
9
1. Turning front wheel
2. Shaving bat
3. Hydraulic oil tank
4. Oil filter
5. Engine
6. Sling rack
7. Water tank
8. Forward and backward
handle
9. Vibration switch
10. Safety lever
11. Throttle lever
12. Shaving bat
13. Manual lock lever
14. Back wheel
15. Starting switch
16. Lock spanner
4
5
2
1
7
8
10
12
14
13
3
9
11
6
Henan Master Machinery Co., Ltd
Tel:(+86)17737606271 www.mastermachinerys.com
10
1. Forward and turning
wheel
2. Shaving bat
3. Hydraulic oil tank
4. Oil filter
5. Engine
6. Sling rack
7. Water tank
8. Forward and
backward handle
9. Vibration switch
10. Safety lever
11. Throttle lever
12. Shaving bat
13. Manual lock lever
14. Back wheel
15. Starting switch
16. Lock spanner
WARNING
1. Comply with safety rules during working.
2. Don’t modify the equipment casually
3. When maintenance, stop the machine
16
15
Altri manuali Master Attrezzature per l'edilizia
