MasterCraft 068-0002-6 Manuale utente
continuation tabs
IMPORTANT:
Please read this manual carefully before assembling
and using this work centre and save it for reference.
INSTRUCTION
MANUAL
BUTCHER BLOCK TOP WORK CENTRE
Model no. 068-0002-6
headline bars
continuation tabs
notes
warnings
headline bars
continuation tabs
notes
warnings
model no. 062-3582-8 | contact us 1-800-689-9928
TABLE OF CONTENTS
2
3
5
6
17
Safety
Parts List
Exploded View
Assembly Instructions
Warranty
NOTE:
If any parts are missing or damaged, or if you have any questions,
please call our toll-free helpline at 1-800-689-9928.
SAVE THESE INSTRUCTIONS
This manual contains important safety and operating instructions.
Read all instructions and follow them with use of this product.
1
TABLE OF CONTENTS
SAVE THESE INSTRUCTIONS
This manual contains important safety and operating instructions.
Read all instructions and follow them with use of this product.
2
headline bars
continuation tabs
notes
warnings
headline bars
continuation tabs
notes
warnings
model no. 068-0002-6 | contact us 1-800-689-9928
• To reduce the risk of serious injury, read the following safety
instructions before assembling and using the cabinet.
• This cabinet is intended for domestic, indoor use only.
• The cabinet should be positioned on a level surface.
• Any assembly or maintenance of the cabinet must be carried
out by adults only.
• Arrange for necessary manpower when assembling and moving
the cabinet.
• Check all the nuts and bolts periodically for tightness.
When required, tighten them again.
• Use a slightly damp, soft cloth to clean the cabinet.
• Do not stand on the cabinet and do not use it as a scaffold.
• Do not exceed the weight limit specified for this cabinet.
Maximum wood board load: 430 lb (195.4 kg)
Maximum bottom panel load: 90 lb (40 kg)
Maximum middle shelf load: 70 lb (31.8 kg)
Maximum drawer load: 40 lb (18 kg)
Maximum pegboard load: 88 lb (40 kg)
Maximum top cantilever shelf: 33 lb (15 kg)
Maximum cabinet load: 871 lb (396 kg)
SAFETY
headline bars
continuation tabs
notes
warnings
headline bars
continuation tabs
notes
warnings
model no. 062-3582-8 | contact us 1-800-689-9928
3
PARTS LIST
No.
1
2
3
4
5
6
7
8
9
10A
10E
11A
11B
11C
11D
11E
12
13
14
15
16
17
18-A
18-B
No.
19
20
21
22
24
25
26
28
29-1
29-2
29-3
29-4
30
42
57
61
27
60
55
27-B
55-A
100
101
102
103
104
105
106
107
Description
Push Bar
Corner Protector
Screwdriver
Key (attached to the front frame)
Drawer Mat
Wrench
Magnet
Pegboard
Top Cantilever Shelf Back Panel
Top Cantilever Shelf Base Panel
Top Cantilever Shelf Left Panel
Top Cantilever Shelf Right Panel
Top Cantilever Shelf Mat
M4 x 30L Screw
Bumper
M4 x 12L Screw
M4 Washer
Mounting Strap
M6 x 50L Screw
M8 Washer
Wall Anchor
1/2" (12.7 mm) Curved
1" (2.5 cm) Curved
1" (2.5 cm) Straight
1 1/2" (3.8 cm) Straight
2" (5.1 cm) Double Prong
4" (10.2 cm) Curved Double Prong
2" (5.1 cm) Plier Holder
2" (5.1 cm) Multi-tool Holder
Description
Solid Hardwood Top
Front Frame
Back Frame
Left Side Panel
Right Side Panel
Middle Shelf
Base Panel
Middlle Panel
Door
Small Drawer Front Panel
Small Drawer Body
Large Drawer Front Panel
Large Drawer Left Panel
Large Drawer Right Panel
Large Drawer Back Panel
Large Drawer Base Panel
Wheel With Brake
Wheel W/O Brake
M8 Washer
M8 x 18L Screw
M4 x 10L Screw
M4 x 8L Screw
Pegboard Support Bar Left
Pegboard Support Bar Right
Qty.
1
1
1
1
1
1
1
1
1
2
2
2
2
2
2
2
2
2
4
4
80
80
1
1
Qty.
1
2
1
2
4
1
2
1
1
1
1
1
1
16
4
2
2
2
2
2
2
4
4
4
4
2
2
2
1
PARTS LIST
4
headline bars
continuation tabs
notes
warnings
headline bars
continuation tabs
notes
warnings
model no. 068-0002-6 | contact us 1-800-689-9928
headline bars
continuation tabs
notes
warnings
headline bars
continuation tabs
notes
warnings
model no. 062-3582-8 | contact us 1-800-689-9928
PARTS LIST
101
104
107
1" (2.5 cm)
Curved
2" (5.1 cm)
Double
Prong
2" (5.1 cm)
Multi-tool
Holder
14 M8
M4 x 8L
Pegboard Support Bar Right
18-B
17
100
103
106
1/2" (12.7 mm)
Curved
1 1/2" (3.8 cm)
Straight
2" (5.1 cm)
Plier
Holder
Mounting Strap
60
Wall Anchor
55-A
M4 x 30L
42
M8 x 18L15
M4 x 12L61
Screw M6 x 50L
55
M4 x 10L16
Pegboard Support Bar Left
18-A
M4 Washer
27
M8 Washer
27-B
M8X20 pcs
102
105
1" (2.5 cm)
Straight
4" (10.2 cm)
Curved Double
Prong
5
EXPLODED VIEW
11A
17
11B
11D
11C
11E
10E
10A
17
6
6
headline bars
continuation tabs
notes
warnings
headline bars
continuation tabs
notes
warnings
model no. 068-0002-6 | contact us 1-800-689-9928
headline bars
continuation tabs
notes
warnings
headline bars
continuation tabs
notes
warnings
model no. 062-3582-8 | contact us 1-800-689-9928
ASSEMBLY INSTRUCTIONS
Fig. A
1
Fig. B
ASSEMBLY PREPARATION
• Begin the assembly of this cabinet on a clean, level surface.
• Remove all items from the box and ensure that all parts listed on page 3 are
present.
• When installing parts that have more than one screw, tighten all screws by
hand before finishing tightening them with the provided screwdriver (21).
If a power screwdriver is used, keep on a low torque setting.
WARNING
Some parts may have sharp edges. To avoid injury, wearing gloves is recommended during assembly.
ASSEMBLY INSTRUCTIONS
1. Open both boxes, locate and remove
the cardboard box containing the Solid
Hardwood Top (Part 1). Set the other parts
to the side.
When assembling this item, place the
Solid Hardwood Top upside down on the
cardboard to avoid scratching the top
surface (Fig. A).
2. Install Back Frame (Part 3) to
Solid Hardwood Top (Part 1)
[Use the Wrench (Part 25) for this step]
Place the Back Frame (Part 3) onto the
Solid Hardwood Top (Part 1), as shown in
Fig. B, and use two Screws (Part 15) and
two Washers (Part 14) and Wrench (Part
25) to fasten. Attach the "Top" of the Back
Frame (Part 3), as indicated by the
attached sticker, to the Solid Hardwood
Top (Part 1) (the Solid Hardwood Top has
no set front or back end) (Fig. B).
Note: Ensure the back and side are flush with the Solid Hardwood Top. When assembling a part,
do not tighten any screws completely until all screws for that part have been partially screwed in.
7
ASSEMBLY INSTRUCTIONS
3.
Install Right Side Panel (Part 5)
Attach Right Side Panel (Part 5) to
Back Frame (Part 3) making sure
the "Top" of Right Side Panel (Part
5) is on the Solid Hardwood Top
(Part 1). Use three Screws (Part 16)
and Screwdriver (Part 21) to fasten
(Fig. C).
4. Install Middle Panel (Part 8)
Attach the Middle Panel (Part 8) to
the Back Frame (Part 3) and Solid
Hardwood Top (Part 1), as shown in
Fig. D, making sure the "Top" of
Middle Panel (Part 8) is attached on
the Solid Hardwood Top (Part 1).
Again, the “Top” is indicated by a
sticker on one of the vertical
columns. Use three Screws (Part
16) and Screwdriver (Part 21) to
fasten (Fig. D).
Fig. C
Fig. D
8
headline bars
continuation tabs
notes
warnings
headline bars
continuation tabs
notes
warnings
model no. 068-0002-6 | contact us 1-800-689-9928
headline bars
continuation tabs
notes
warnings
headline bars
continuation tabs
notes
warnings
model no. 062-3582-8 | contact us 1-800-689-9928
ASSEMBLY INSTRUCTIONS
5.
Install Left Side Panel (Part 4)
Attach Left Side Panel (Part 4) to
Back Frame (Part 3), making sure
the "Top" of Left Side Panel (Part
4) is on the Solid Hardwood Top
(Part 1). Use three Screws (Part 16)
and Screwdriver (Part 21) to fasten
(Fig. E).
6.
Install the Front Frame (Part 2)
A: Align the "Top" of the Front
Frame (Part 2) to the Solid
Hardwood Top (Part 1). The other
screw holes will align with the Left
and Right Side Panels (Part 4 and
5) and Middle Panel (Part 8).
B: Use nine Screws (Part 16) and
Screwdriver (Part 21) to fasten the
Front Frame (Part 2) to the Left and
Right Side Panels (Part 4 and 5)
and Middle Panel (Part 8).
C: Make sure the four edges of the
Cabinet are aligned, then fasten
the Front Frame (Part 2) to the
Solid Hardwood Top (Part 1) by
using two Washers (Part 14) and
two Screws (Part 15) with Wrench
(Part 25) (Fig. E).
Fig. E
Fig. F
Note:
The Key (Part 22) is attached to the
front frame (Part 2). Please take out the
Key (Part 22) before installing the front
frame (Part 2).
Altri manuali per 068-0002-6
1
Indice
Lingue:
Altri manuali MasterCraft Deposito attrezzi
