Max BC-PB-2-WM-2 Manuale utente
Eco Switch
BC-PB-2-WM-2
Operating manual
2
Scope of delivery
Quan-
tity
Item
1x MAX! Eco Switch
1x Clip-on frame
1x Mounting plate
2x Plug
6x Screws
2x Adhesive stripes
2x 1.5 V LR03/micro/AAA batteries
3x Brief instruction in German/English, French/
Dutch and Polish/Italian
Scope of delivery
3
Table of contents
Table of contents
1 Information about this manual .............................4
2 Safety instructions.................................................4
3 Function.................................................................5
4 Overview ................................................................7
5 Start-up .................................................................8
6 Mounting in existing switches.............................12
7 Teaching-in ..........................................................13
8 Restore factory settings ......................................15
9 Flashing sequences and transmission behaviour. 15
10 Maintenance and cleaning ..................................16
11 Information about radio operation......................16
12 Technical specifications ......................................17
1st English edition 07/2014
Documentation © 2014 eQ-3 Ltd. Hong Kong
All rights reserved.
Translation of the original version in German.
Version 1.0
4
Information about this manual
1 InformatIon about thIs manual
Read this manual carefully before starting to use the de-
vice. Keep the manual so you can refer to it at a later date
if you need to. If you hand over the device to other persons
for use, please hand over the operating manual as well.
Symbols used:
Attention!
This indicates a hazard.
Note.
This section contains important additional in-
formation.
2 safety InstructIons
The device is not a toy; do not allow children to
play with it. Do not leave packaging material lying
around, as it can be dangerous in the hands of a
child.
Do not open the device: it does not contain any
components that need to be serviced by the user.
In the event of an error, please return the device
to the service department.
The device may only be operated indoors and must
be protected from the effects of damp and dust,
as well as solar or heat radiation.
5
Function
Using the device for any purpose other than that
described in this operating manual does not fall
within the scope of intended use and shall inval-
idate any warranty or liability. This also applies
to any conversion or modification work. The de-
vice is intended for private use only.
3 functIon
With the MAX! Eco Switch, you can leave your house or
apartment and switch all rooms into manual mode and
reduction temperature - at the push of a button! When
you enter the house or apartment again, you can also set
all rooms back to auto mode by only one button press.
The individually set week programs for the rooms will
then be executed. Communication between the MAX!
components is bidirectional. This ensures that the in-
formation sent reaches the recipient.
The MAX! Eco Switch is battery-operated. As such it is
highly flexible where mounting and selecting a mount-
ing location are concerned. The device is mounted and
removed very easily using screws or adhesive strips. It is
compatible with a number of different surfaces including
furniture, brick walls, tiles or glass. Holes or slits do not
have to be chiselled out of brick walls. A flush-mounting
box is not required for operation. The frame supplied can
be used for wall mounting. It is also possible to integrate
the MAX! Eco Switch into existing switches (see sec. „6
6
Function
Mounting in existing switches“ on page 12).
The MAX! Eco Switch can be used within the MAX! House
solution:
MAX! House solution
This is the solution for the entire house. With a
MAX! Cube, all settings of connected devices in
the house can comfortably be made via the MAX!
software.
By using the MAX! Cube, several MAX! Radiator so-
lutions and MAX! Room solutions can be connect-
ed to a MAX! House solution in a new installation.
7
Overview
4 overvIew
(A) Mounting plate
(B) Clip-on frame
(C) Electronic unit/push-button
(D) Device LED
D
A
B
C
8
Start-up
5 start-up
5.1 InsertIng (replacIng) batterIes
As-delivered condition
When you are starting up the device for the first time,
first remove the mounting plate (A) on the rear of the
MAX! Eco Switch.
• To do this, hold the MAX! Eco Switch firmly in one
hand and pull off the installation plate at one corner.
Mounted condition
Once mounted, the electronic unit can easily be pulled
out of the frame.
• Pull the electronic unit off the wall together with the
framebypulling sidewaysat theframe.Youdonot need
to remove the rocker or open the device.
Replacing batteries
• Turn the electronic unit over to remove or insert the
batteries according to the illustration.
• After removing the old batteries, please wait approx.
60 seconds.
• Insert two new 1.5 V LR03/micro/batteries in the bat-
tery compartments (making sure that you insert them
the right way round).
9
Start-up
• Put the electronic unit back into the frame.
Never recharge standard batteries. Do not throw
the batteries into a fire. Do not expose batteries
to excessive heat. Do not short-circuit batteries.
Doing so will present a risk of explosion.
Used batteries should not be disposed of with
regular domestic waste! Instead, take them
to your local battery disposal point.
5.2 mountIng
You can either use screws or adhesive strips to mount
the MAX! Eco Switch to a wall in the frame supplied or
integrate it into an existing switch (see sec. „6 Mounting
in existing switches“ on page 12).
Adhesive strip mounting:
• Choose a site for installation.
10
Start-up
The surface on which you are mounting the device
must be clean, dry and free of grease.
• For mounting the assembled MAX! Eco Switch, attach
the adhesive strips to the rear of the mounting plate.
You should be able to read the letters on the back side
(according to figure).
<PA66>
• Remove the protective film from the adhesive strips.
• Press the assembled MAX! Eco Switch with the back
side to the wall in the position where it should sub-
sequently be attached.
Screw mounting:
• Choose a site for installation.
Make sure that no electricity or similar lines run
in the wall at this location.
Indice
