Maxon GPC 22 X1 Manuale utente
Cantilever GPC X1
Operator`s Manual
Liftgate
Series
GPC 22 X1
Lift CORP.
11921 Slauson Avenue.
Santa Fe Springs, CA 90670
(800) 227 - 4116 © Sörensen Hydraulik GmbH
Version 2011
Document no.: S 20 909 946
Lift CORP.
Operator`s handbook Series GPC 22 X1
Document no.: S 20 909 946 1Version: 2011
General
You have chosen a lift gate of the highest quality. The lift gate is a low maintenance unit. It is
equipped with maintenance-free, grease-free bearings and does not require greasing
throughout its entire lifetime.
The lift gate may only be used for the raising and lowering of loads, which must be loaded in
accordance with the load diagram.
The lift may be operated, maintained and serviced only by persons who have received
appropriate training and who have been specifically instructed of the dangers associated with
its operation.
The accident prevention regulations, must be observed. If they are not, the manufacturer
cannot accept any liability for resultant damage or injury.
These operating instructions are valid for following lift gates :
Model Capacity kg Capacity pounds
GPC 22 X1 1000 kg 2200 pounds
Daily verifications :
•Check for correct and normal operation
•Legibility of all operating and information labels
•Check for weld cracks and make sure all bolts and nuts are tight
•Check for leaks on hoses, valves and hydraulic cylinders
•If platform has warning lights please check for function
The driver should report any incorrect operation or obvious damage
to his maintenance department. All damages are to be mended
immediately. The lift gate owner is responsible for the repairs of
detected damages.
The operating instructions are to be carried in the vehicle at all
times.
Lift CORP.
Operator`s handbook Series GPC 22 X1
Document no.: S 20 909 946 2 Version: 2011
Yearly check
The lift gate must be checked for damages at least once a year by trained personnel. The
results of this verification must be written down in the maintenance book.
Battery capacity
Lift capacity Up to 2200 lbs
12V : 1 x 12V 88 Ah
24V : 2 x 12V 66 Ah
Battery size Group 31
For use in short-haul traffic the next step up should always be selected.
Heavy-duty alternators are strongly recommended.
The operator is resp onsible for the battery capacity and the c harge status of the
battery.
The electric motor
You can avoid damages to the motor or the power relais if you ensure that you have the right
voltage at all times. If the motor has trouble with a load that is normally lifted without a
problem, stop the lifting operation immediately and charge the batteries.
If, in your opinion, the batteries are empty too fast, have the batteries and the power cables
checked by a specialist.It could be possible that the cables, the mass connection or the
batteries have to be repaired or changed.
Lift CORP.
Operator`s handbook Series GPC 22 X1
Document no.: S 20 909 946 3Version: 2011
Switching on the lift gate
Switch the lift gate on with the push button located in the cabin. When the red lamp lits, the
lift is ready for operation
Description of the controls
Hand control box
All functions must be operated with two hands by switching the toggle switches located at the
side of the hand control box
Lift
Lower
Open / tilt down
Close / tilt up
Hand control box 2 Buttons
Lift Lower
Lift CORP.
Operator`s handbook Series GPC 22 X1
Document no.: S 20 909 946 4 Version: 2011
Hand control box 3 Buttons
Open / tilt down Close / tilt up
Foot Controls (Optional version)
The foot controls are connected so that they only work when pushed in a specific order.
To lift and tilt up
Step 1 - activate foot control button for lowering
Step 2 - activate foot control button for lifting
To lower and tilt down
Step 1 - activate foot control button for lifting
Step 2 - activate foot control button for lowering
Lift CORP.
Operator`s handbook Series GPC 22 X1
Document no.: S 20 909 946 5Version: 2011
General Information
Standing on the platform when it is moving
As it is only allowed for the operator to stand on the platform, he must ensure that no other
person (especially children) are standing inside the danger zone.
Hazard information for unsecured loads
Under certain circumstances, there is a possibility that the front axle of the vehicle lifts while
unloading. On this inclination, unsecure loads may start to slip and create a danger for the
operator.
You can purchase a warning sticker
CAUTION ! Secure the load against
moving or use mechanical supports
Lift CORP.
Operator`s handbook Series GPC 22 X1
Document no.: S 20 909 946 6 Version: 2011
Description of the Safety Installations
Hose Rupture Valves
If a hose, a pipe or a screw connection should burst, the lift gate lowers or inclines in a
controlled manner at the permitted speed, as long as a function is connected via one of the
control units (hand held remote controls, foot controls or hand control box). If such control
unit is not activated, or ceases to be activated, the lift gate stops automatically.
Safety Valve
The lift gate is protected by the factory-set safety valve from raising loads which are heavier
than the specified carrying capacity. This valve may only be adjusted by an expert using a
test weight and a manometer.
Fuses
Defective fuses may only be replaced by fuses which correspond to the values specified in
the wiring diagram and on the distributor plate. Larger fuses may not be blown in the event of
malfunctions, which could lead to cables catching fire.
Roll-off Safety Devices
If roller containers are being used, the lift gate should be equipped with roll-off safety
devices. Their operation is impaired by dirt; the operator should keep the roll-off safety
devices clean at all times.
Warning Flags
The flags can be seen until the platform is on the ground. Both safety installations should be
kept clean and in perfect condition at all times.
(Optional version)
Warning Lights
The lights flash as soon as the platform has opened a few degrees.
Lift CORP.
Operator`s handbook Series GPC 22 X1
Document no.: S 20 909 946 7Version: 2011
Standing on the platform when it is moving
When loading the platform, please ensure that you leave enough space for the operator to
securely operate the lift gate.
Securing of Loads
Rolling and sliding loads must be secured on the platform. Lift gates come optionally
equipped with cart stops, securing rolling loads with the maximum efficiency (wheels with
maximum diameter 4” )
Caster diameter max. 4“
Lift CORP.
Operator`s handbook Series GPC 22 X1
Document no.: S 20 909 946 8 Version: 2011
Safety guide for the operation of the lift gate
Secure the load against toppling over and sliding
Altri manuali per GPC 22 X1
1
Indice
Altri manuali Maxon Sistema di sollevamento
Maxon
Maxon RA-35 Manuale utente
Maxon
Maxon GPC 17 X-1 Manuale utente
Maxon
Maxon TUK-A-WAY 72-150 LMV Manuale utente
Maxon
Maxon GPTLR Series Manuale utente
Maxon
Maxon GPT Series Manuale utente
Maxon
Maxon GPS 44X1 GPS Manuale utente
Maxon
Maxon WL7 Manuale utente
Maxon
Maxon BMR-55 Manuale utente
Maxon
Maxon TE-15 Manuale utente
Maxon
Maxon TUK-A-WAY MTB-25 Manuale utente
Maxon
Maxon RA-45 Manuale del proprietario
Maxon
Maxon GPSLR Series Manuale utente
Maxon
Maxon TE-25 Manuale utente
Maxon
Maxon 80 Series Manuale utente
Maxon
Maxon BMR-35 Manuale utente
Maxon
Maxon GPC 22 X1 10 Series Manuale utente
Maxon
Maxon BMR Series Manuale utente
Maxon
Maxon GPSLR Series Manuale utente
Maxon
Maxon GPC 22 X1 Manuale utente
Maxon
Maxon GPTLR Series Manuale utente
Manuali Sistema di sollevamento popolari di altre marche
Genie
Genie Z-60/34 Manuale utente
Screen Technics
Screen Technics INTERFIT Vertical Up Lift Manuale utente
Mortuary Lift
Mortuary Lift ULTIMATE 1000 Manuale utente
Custom Equipment
Custom Equipment Hy-Brid 3 Series Manuale di programmazione
Custom Equipment
Custom Equipment Hy-Brid Lifts 2 Series Manuale di programmazione
Hy-Brid Lifts
Hy-Brid Lifts HB-P3.6 Manuale di programmazione
