MAXSA 44150-SL Guida di riferimento rapido
1
ASSEMBLY & OPERATING INSTRUCTIONS
IMPORTANT: READ ALL INSTRUCTIONS CAREFULLY BEFORE USE
ABOUT YOUR SOLAR SECURITY LIGHT
During the day, the solar panel included with this MAXSA Solar Security Light converts
sunlight into electricity, recharging the pre-installed battery. Using this stored energy,
the 150 LED lights turn on automatically at night when motion is detected, producing
787.5 lumens. This MAXSA Solar Security Light has an adjustable TIME dial that allows
light duration of up to 60 seconds. When the battery is fully charged, this Solar Security
Light can light up for up to 80 minutes, which is equivalent to 80 one-minute cycles when
the TIME dial is set to the maximum (+) position.
The unit includes a rechargeable 3.7V / 4.4Ah Lithium Ion battery pack and will need to
be replaced when the charging ability is decreased.
Model #: 44150-SL
2
Carefully remove and identify all the parts from their protective packaging and lay them
out in front of you.
INCLUDED PARTS:
2
Carefully remove and identify all the parts from their protective packaging and lay
them out in front of you.
INCLUDED PARTS:
the solar panel to your Solar Security Light
by plugging the 15 foot cord into the cord
attached to the front of the Solar Security
Light. Turn and twist the cords while pressing
Adjustment dials are located on the underside of the motion sensor. Move the
motion sensor to allow for easier access to the controls. Move sensor back into
position upon completion.
Once you have identified all parts, connect the solar panel to your Solar Security Light by
plugging the 15 foot cord into the cord attached to
the front of the Solar Security Light. Turn and twist
the cords while pressing firmly together until they
are attached tightly.
Adjustment dials are located on the underside
of the motion sensor. Move the motion sensor
to allow for easier access to the controls. Move
sensor back into position upon completion.
3
CHOOSING A LOCATION FOR YOUR SOLAR SECURITY LIGHT
This Solar Security Light comes complete with a solar panel attached to a 15 foot power
cord. For optimum sun exposure and longer light output, place the solar panel in a
position that receives at least 6-8 hours of direct sunlight per day. Placing the solar panel
in a shaded location or even behind a window will not allow the battery to charge fully,
reducing the number of hours the light will operate per evening. Ensure that the solar
light is not placed near nighttime light sources such as porch lighting or street lighting.
This Solar Security Light is ideal for lighting up areas where electricity is not available
— including porches, driveways, carports, garages and entrance areas – for safety and
security around your home.
When deciding where to mount the light, keep in mind that the motion sensor has a field of
vision of 180º (horizontal) at a distance of up to 40 feet when the surrounding temperature
is 75°F. The outside temperature will impact the detection distance.
HOW TO INSTALL YOUR SOLAR SECURITY LIGHT
1. Mount the Security Light onto a solid surface, using the two (2) wood/sheet metal
screws supplied. You may mount the Security Light either vertically or horizontally.
2. Use the four (4) wood/sheet metal screws supplied to mount the solar panel onto a
solid surface. You can adjust the angle of the solar panel by gently rotating the solar
panel to a different locking position. Remember to face the panel south for direct
sunlight exposure.
4
TOOLS REQUIRED FOR INSTALL
If mounting on a wood or softer surface, you only need a Phillips-head screwdriver! If
mounting on concrete, brick, or a harder surface, a drill should be used to create the
mounting holes first
BEFORE FIRST USE OF YOUR SOLAR SECURITY LIGHT
1. Ensure the power switch on the main body of your Security Light is in the OFF position.
In this position, the solar panel will charge the battery without activating the unit.
2. Leave the switch in the OFF position for 3 days with the solar panel placed in direct
sunlight, ideally facing the Southern sky. This will ensure that the battery in your
Solar Security Light has a full charge prior to motion sensor adjustment and normal
operation.
OPERATING YOUR SOLAR SECURITY LIGHT
After the initial 3 day charge of your Solar Security Light, move the switch on the main body
to the AUTO position. When you do this, the light should activate immediately, regardless
of lighting conditions or motion. This is a test activation to show there is power flowing
from the battery to the light. It should last roughly 30 seconds. After this test activation,
the light will function based on the dial settings mentioned below. Your Solar Security Light
is now ready for use.
Underneath the motion sensor, there are 3 adjustment dials: TIME/SENS/LUX. The light
has been factory preset as follows:
TIME Set at 30 seconds.
SENS Set at a 10 - 15 foot range (when the surrounding temperature is 75 F).
LUX Set for your Security Light to activate at dusk when motion is detected.
If the above settings are not suitable for your application, then these may be adjusted using
the steps below.
TIME PERIOD ADJUSTMENT (TIME)
The time period control dial sets the duration of the light upon each activation that the Solar
Security Light will remain illuminated after the last detected motion. The time period has an
adjustable range of 10 seconds to 1 minute.
To decrease the time period, move the dial toward the ( – ) symbol.
To increase the time period, move the dial toward the ( + ) symbol.
Test the time period by triggering the motion sensor and measure the time period the light
stays on. Adjust the TIME control until the desired illumination duration is reached.
A shorter TIME setting will conserve battery life. For best results, use the shortest TIME
setting for your location as possible.
MOTION SENSOR ADJUSTMENT (SENS)
The motion sensor on this Solar Security Light is temperature-sensitive. The cooler the
temperature, the more sensitive the motion sensor will become. Use the SENS dial to
5
adjust the sensitivity of the motion sensor to compensate for environmental temperature
changes. The motion sensor is most sensitive when the SENS dial is turned fully clockwise
(+).
To decrease sensitivity, move the dial toward the ( – ) symbol.
To increase sensitivity, move the dial toward the ( + ) symbol.
To test the motion sensitivity, aim the sensor head toward the desired area. Set the TIME
dial to minimum ( – ) position and the LUX dial to the bright setting ().
Walk slowly around the area of detection, changing your walking pace until the light comes
on. If light does not come on, you may need to adjust the angle of the sensor unit. Make
adjustments as needed until the desired level of sensitivity is reached. Re-adjust the TIME
and SENS dials when complete.
LIGHT LEVEL ADJUSTMENT (LUX)
The LUX dial controls the natural light level that triggers the Solar Security Light and
prevents the light from operating during daylight hours.
Your Solar Security Light comes preset for activation at dusk.
To adjust for activation in a brighter setting, move the dial toward bright ()
To adjust for activation in a darker setting, move the dial toward dark ( ).
REPLACING THE BATTERY PACK
When the charging ability of the battery pack decreases, you can replace it with a new
3.7V/4.4 Ah Lithium-Ion battery pack. Follow the steps below when replacing the battery
pack.
Battery Pack
1. First remove the main unit from its mounted surface and unplug the solar panel.
2. Move the power switch on the main body to the OFF position.
3. Remove the four (4) screws on the back of the main unit that hold the halves together.
4. Once the unit is open, carefully remove the bracket holding the battery pack in place
by unscrewing the two (2) screws as indicated in the diagram above.
5. Carefully unplug the battery pack from the unit. Be sure to pull by the base of the plug.
Do not pull the plug by the wires as this may damage the unit.
6. Carefully remove the battery pack and replace with a new 3.7V / 4.4Ah Lithium Ion
battery pack obtained from MAXSA Innovations. The plug will only fit in one orientation.
Do not force the plug into place as this may damage the unit. If it does not fit, rotate
the plug until it matches with the receiving end on the circuit board.
6
7. Replace the bracket to hold the battery pack in place by using the two (2) screws
removed in step 4, taking care not to damage any cables.
8. Re-assemble the main unit by screwing the two (2) halves of the main body together
securely.
9. Once assembled, mount your Solar Security Light to its original surface location.
10. Repeat the steps in the “Before first time use of your Solar Security Light” section on
page 4 to ensure your new battery is fully charged.
NOTE: Do not dispose of batteries in general household trash or into a fire since
the battery pack may explode. Consult your local regulations for correct
disposal of Lithium-Ion batteries. The battery pack may also be returned to
MAXSA Innova-tions at 8412 Cathedral Forest Dr., Fairfax Station, VA 22039.
Do not take apart the battery pack since they contain corrosive chemicals.
MAINTENANCE TIPS
The LED lights in your Solar Security Light will last up to 30,000 hours and should never
need replacement.
To keep your Solar Security Light looking new, keep the lens free of dust and deposits by
wiping occasionally with a dry cloth or with warm soapy water.
It is important that the solar panel is kept free of dirt and debris at all times. A dirty
solar panel will not allow the battery pack to be fully charged. This will shorten the life of
the battery pack and may cause the light to malfunction.
STORAGE
If you wish to store your light indoors for more than two or three days, turn the power
switch to the OFF position to prevent damage to the battery pack. Battery capacity may
be reduced during prolonged storage. For optimal performance, we recommend that you
do not store your Solar Security Light for prolonged periods of time.
EXTENSION CORDS:
A 15-foot extension cord is available for this product for $14.95, which covers shipping and
handling costs as well. This extension cord allows the solar panel to be placed higher
or further away from the security light to ensure maximum direct sunlight exposure. Ask
for extension cord model EXT-Black. For more information, please call 703-495-0661.
7
TROUBLESHOOTING
PROBLEM POSSIBLE SOLUTIONS
Light will not
switch on
when there is
movement in
the detection
area.
•Ensure that the power switch on the main body has been
turned to the AUTO position.
•Ensure that the motion sensor has been positioned to face
oncoming movement.
•Ensure that the battery has been fully charged in direct sunlight
for 3 sunny days. Refer to the “Before First Use of Your Solar
Security Light” section on page 4.
•Check to see that the solar panel is facing south so that it
receives direct sunlight for most of the day, enabling the
battery to fully charge.
•Check to see that the LUX control has not been set too far
towards ( ). Setting the LUX control too far towards ( ) will
cause the Solar Security Light to turn on only in complete
darkness.
•Check to see that the motion sensor is not near night time light
sources such as street lights.
Light switches
on during the
day.
•The LUX control may be set too far towards the () position.
•Reposition the motion sensor.
Light switches
on for no
apparent
reason.
•The SENS control may be set too far towards the (+) position.
•Moving trees, traffic, pets or birds may be getting in the area of
detection. This may be unavoidable, however the sensor could
be redirected to a height where this is less likely to occur.
•If there are reflective objects in the detection area such as
windows, water, or white walls, you may need to redirect or
possibly reposition the motion sensor.
•Test the motion sensor by covering it completely with
cardboard and waiting several minutes to make sure it does
not detect motion. If the light still switches on, please contact
MAXSA for further assistance.
Light quickly
flashes on and
off.
•Battery charge may be low. Turn the power switch to the OFF
position and charge the battery for three (3) sunny days with
the solar panel placed in direct sunlight, ideally facing the
Southern sky.
•Move the LUX control more to the () position.
Light is not
as bright as
normal.
•Battery charge may be low. Turn the power switch to the OFF
position and charge the battery for three (3) sunny days with
the solar panel placed in direct sunlight, ideally facing the
Southern sky.
8
ONE YEAR LIMITED WARRANTY
1 YEAR LIMITED WARRANTY: MAXSA Innovations, LLC warrants to the original
consumer/purchaser that this product shall be free of defects in material and workmanship
under normal use and circumstances for a period of one (1) year from the date of original
purchase for use. When the original consumer/purchaser returns the product pre-paid
(consumer pays return shipping) to MAXSA Innovations, LLC, 8412 Cathedral Forest Dr;
Fairfax Station, VA 22039; USA within the warranty period, and if the product is defective,
MAXSA Innovations, LLC will at its option repair or replace such. This warranty shall
constitute the sole liability of MAXSA Innovations, LLC concerning the product. MAXSA
Innovations, LLC expressly disclaims all other warranties INCLUDING, WITHOUT
LIMITATION, THE WARRANTIES OF MERCHANT ABILITY AND FITNESS FOR A
PARTICULAR PURPOSE. NO PERSON, FIRM, OR COPORATION IS AUTHORIZED
TO ASSUME FOR MAXSA Innovations, LLC ANY OTHER LIABILITY IN CONNECTION
WITH THE SALE AND USE OF THE PRODUCT. MAXSA Innovations, LLC and agents
and distributors will bear no liability whatsoever for incidental or consequential damages
or charges of any kind. Some states do not allow the reclusion or limitation of incidental
or consequential damages, so the above disclaimer regarding incidental or consequential
damages may not apply to you. This warranty is void if the product has been damaged
or tampered with or if the product or any such parts have been opened. In all cases of
damage during shipment, a claim must be filed with the shipping carrier and not with
MAXSA Innovations, LLC. This warranty gives you specific legal rights; you may also have
other rights which vary from state to state.
MAXSA Innovations, LLC
8412 Cathedral Forest Drive
Fairfax Station, VA 22039
Tel: 703-495-0661
www.maxsainnovations.com
v14.4
©2014 MAXSA Innovations, LLC
Please save these instructions for future reference.
MADE IN CHINA
SPECIFICATIONS
Power Source: Solar
Lumens: 787.5
Light Color: 6500K (Cool White or Daylight color)
Function: Motion-Activated
Power Storage: 3.7V/4.4Ah Lithium-ion battery pack
Light Duration: 10 - 60 seconds after motion stops
Maximum Runtime: 80 minutes on a full charge
Detection Angle: 180°
Maximum Detection Distance: 40 feet (12.2 meters)
Weatherproof Rating: IP44
9
INSTRUCCIONES GENERALES
DE INSTALACIÓN Y FUNCIONAMIENTO PARA EL MODELO 44150-SL
IMPORTANTE: LEA TODAS LAS INSTRUCCIONES CUIDADOSAMENTE ANTES DE USAR.
ACERCA DE SU LUZ SOLAR DE SEGURIDAD
Durante el día, el panel solar incluido en esta unidad de seguridad recarga la batería.
Con esta energía guardada, las luces LED se encienden automáticamente por la noche
cuando detectan movimiento. Esta luz solar de seguridad tiene un marcador de tiempo
ajustable que permite la duración de luz. Cuando la batería está completamente cargada,
la luz solar de seguridad se encenderá durante un máximo de 80 minutos, lo que
equivale a 80 ciclos de un minuto cuando el botón giratorio de tiempo (TIME) está ajustad
o en la posición máxima (+).
La batería incluida tendrá que ser sustituido cuando se disminuye la capacidad de
carga.
Modelo #: 44150-SL
ESPAÑOL
LUZ SOLAR DE SEGURIDAD ACTIVADO POR EL MOVIMIENTO
10
Retire con cuidado e identifique todas las piezas del envase protectiva y ponlas en frente
de usted.
PIEZAS INCLUIDAS:
Tornillos y tacos
para montaje en
panel solar
Cable de
alimentacíon
Panel Solar
Tornillos y anclajes
para montaje en
panel solar
Cubierta de la luz
Sensor de
movimiento
Para el
ajustamiento de
montaje
El panel solar
soporte de
montaje
Unidad de la
batería principal
AUTO/OFF
interruptor
Una vez que haya identificado todas las piezas, conecte el panel solar a la luz solar
de seguridad a través del cable de 15 pies al cable localizado en la parte delantera
de la luz solar de seguridad. Gire las cuerdas
mientras presione con fuerza hasta que se unen
fuertemente.
Botones giratorios de ajuste se encuentran en la
parte inferior del sensor de movimiento. Mueva
el sensor de movimiento para permitir un acceso
más fácil a los controles. Coloque el sensor de
movimiento en su posición original al terminar.
Botón de ajuste para el tiempo de duración
Botón de ajuste de sensibilidad de movimiento
Botón de ajuste de sensibilidad a la luz
Indice
Lingue:
Altri manuali MAXSA Proiettore
MAXSA
MAXSA 40330 Manuale utente
MAXSA
MAXSA 40330 Guida di riferimento rapido
MAXSA
MAXSA 40227 Guida di riferimento rapido
MAXSA
MAXSA 43030 Guida di riferimento rapido
MAXSA
MAXSA 40220 Guida di riferimento rapido
MAXSA
MAXSA BRIGHT 44449-L Guida di riferimento rapido
MAXSA
MAXSA 44216 Guida di riferimento rapido
MAXSA
MAXSA 40227 Guida di riferimento rapido
MAXSA
MAXSA 40331 Guida di riferimento rapido
MAXSA
MAXSA 40330 Guida di riferimento rapido
