Maytag Atlantis III Manuale utente
©2002 Maytag Appliances Company 16009485-03 Rev. 0 1
INTRODUCTIONINTRODUCTION
INTRODUCTIONINTRODUCTION
INTRODUCTION
Attached is Supplement three for service manual 16009485. This Maytag Washer
Service Manual supplement covers
Atlantis III ModelsAtlantis III Models
Atlantis III ModelsAtlantis III Models
Atlantis III Models
. We suggest you file this
with your 16009485 Manual for reference.
CONTENTSCONTENTS
CONTENTSCONTENTS
CONTENTS
SECTION 1. Product Definition .............................................................................. 2
SECTION 2. Console ............................................................................................ 2
SECTION 3. Automatic Temperature Control ......................................................... 3
SECTION 4. Water Valves ..................................................................................... 3
SECTION 5. Front Removal ................................................................................... 4
SECTION 6. Pump Assembly ................................................................................ 4
SECTION 7. Tub Seal and Bearing ........................................................................ 4
To locate an authorized servicer, please consult your telephone book or the dealer from
whom you purchased this product. For further assistance, please contact:
Customer Service Support Center
CAIR Center
Web Site Telephone Number
WWW.AMANA.COM................................................ 1-800-843-0304
WWW.JENNAIR.COM ............................................. 1-800-536-6247
WWW.MAYTAG.COM ............................................. 1-800-688-9900
CAIR Center in Canada ........................................... 1-800-688-2002
Amana Canada Product ........................................... 1-866-587-2002
2 16009485-03 Rev. 0 ©2002 Maytag Appliances Company
•The Control Wire Harness has a connector
which allows removal of the entire Console
Assembly from the cabinet.
• Automatic Temperature Control. The incoming
water temperature is controlled by 2 thermostats
attached to the Injector Assembly.
Section 2. Console
Disassembly and Testing
The Console Assembly has been designed to allow full
removal of the console from the cabinet via a plug
added to the wiring harness. This feature will also aid
in performing diagnostic tests to the various
components.
• A new non-serviceable water pump.
Section 1. Product Definition:
The Atlantis III is similar to previous Atlantis washer models, with the following exceptions:
5
3
W
H
3
7
G
Y
5
1
P
U
1
3
O
R
1
1
B
U
1
5
B
R
2
2
R
D
3
2
B
K
M
Y
L
3
2
B
K
3
1
O
R
9
W
H
2
1
B
R
Centrifugal Switch
Attach Ohm Meter leads to BK 32 and OR 31 .5 ohms.
Overload
Attach Ohm Meter leads to WH 9 and YL M .5 ohms.
Water Valves
Hot
Attach Ohm Meter leads to OR 13 and BR 15 1 ohm.
Cold
Attach Ohm Meter leads to BU 11 and BR 1 ohm.
Motor Resistance
Main Winding
Attach Ohm Meter leads to WH 9 and BK 32 2 ohms.
Start Winding
Attach Ohm Meter leads to BR 21 and RD 22 4 ohms. Lower harness shown from wire insertion side
©2002 Maytag Appliances Company 16009485-03 Rev. 0 3
ATC Functionary
The nozzle of the water valve directs the incoming
water over two thermostats mounted onto the upper
injector assembly. One of the thermostats controls the
cold water valve, and the other controls the hot water
valve.
When ATC cold wash is selected:
The cold water valve is opened for full cold fill. If the
incoming water temperature is below approximately
65°F, the hot water valve will open and warm the
incoming water. The hot water valve will continue to
cycle on and off maintaining optimum cold water
temperature until the tub is full. The target water
temperature for a cold wash is 70°F to 80°F.
When ATC warm wash is selected:
The hot water valve is opened for full hot fill. If the
incoming water temperature is above approximately
100°F, the cold water valve will open and cool the
incoming water. The cold water valve will continue to
cycle on and off maintaining optimum warm water
temperature until the tub is full. The target water
temperature for a warm wash is 90°F to 100°F.
ATC is not active during rinse or hot wash.
Section 3. Automatic
Temperature Control Section 4. Water Valves
Water Valve Access
Water valve access is gained by lifting the top assem-
bly. The water valve is located just behind the Auto-
matic Temperature Control Assembly and mounted to
the back cabinet wall. To remove the water valve.
Disconnect water lines and remove one screw on the
left side of the water valve mounting bracket. Slide
bracket to the left and remove.
4 16009485-03 Rev. 0 ©2002 Maytag Appliances Company
Section 5. Front Removal
Procedure
Lift Top Assembly by releasing spring clips between
top and front panel. Use a plastic putty knife to
disengage clip. Lift top and remove top screws through
the back of the Front Panel. There are two spring clips
a screws one each side.
Section 6. Pump Assembly
Atlantis washers use a new pump assembly which will
be totally replaced should it require repair. A pump kit
will be available containing the entire pump assembly.
The Allantis III Seal and Bearing are unique and are
matched to the duel drive high torque transmission,
used on this washer. When replacing the seal and
bearing, order parts specific to the Atlantis III washer.
The seal and bearing used on older models will not
fuction properly. The seal kit will also be supplied with
the replacement transmission assembly if it is
necessary to install a new one.
Section 7. Tub Seal and
Bearing
Triple Seal
Questo manuale è adatto per i seguenti modelli
1
Altri manuali Maytag Rondella
Maytag
Maytag MTW6700TQ - 28" Washer Manuale utente
Maytag
Maytag MFR18 Manuale utente
Maytag
Maytag PAV5158AWW Manuale utente
Maytag
Maytag MVW18CSBGW0 Manuale utente
Maytag
Maytag Performa LAT3500 Manuale utente
Maytag
Maytag MTW6700TQ1 Manuale utente
Maytag
Maytag YMHWE251 Series Manuale utente
Maytag
Maytag MVWC7ESWW Manuale utente
Maytag
Maytag MHWE450WJ Manuale utente
Maytag
Maytag BRAVOSTM Manuale utente
Maytag
Maytag AUTOMATIC WASHER Manuale utente
Maytag
Maytag MHW7000AG Manuale utente
Maytag
Maytag MVWX600XW Manuale utente
Maytag
Maytag MHWE400W Series Istruzioni per il montaggio
Maytag
Maytag MFR25 Manuale utente
Maytag
Maytag MVWB450WQ0 Manuale utente
Maytag
Maytag W10560152B - SP Manuale utente
Maytag
Maytag MHWZ600TB00 Manuale utente
Maytag
Maytag MFS25PN Manuale utente
Maytag
Maytag MHWC7500YW0 Manuale utente
