MC Technologies MC92 Manuale utente
MC92
LTE Data-Gateway/Terminal
MC Technologies GmbH, Kabelkamp 2, 30179 Hannover, Germany
Tel: +49511 67 69 99-128, Fax: +49511 67 69 99-150, www.mc-technologies.net, www.mc-technologies.com, Email: [email protected]
1
Quick Guide
MC92
MC Technologies GmbH ‐ Kabelkamp 2 ‐ D‐30179 Hannover
Telefon +49 511 67 69 99 128 ‐ Fax +49 511 67 69 99 150
www.mc‐technologies.net - www.mc-technologies.com
info@mc‐technologies.net
V1.0.4
MC92
LTE Data-Gateway/Terminal
MC Technologies GmbH, Kabelkamp 2, 30179 Hannover, Germany
Tel: +49511 67 69 99-128, Fax: +49511 67 69 99-150, www.mc-technologies.net, www.mc-technologies.com, Email: [email protected]
2
Installation
The MC92 data terminal is designed for applications over LTE with fall back to UMTS, EDGE and GSM
multifunctional applicable.
Please follow the instructions step by step and configure the settings for the SIM card. An incorrect
PIN can lead to the SIM card being blocked.
Warning: user must be at least 20 cm away from the transmitting antenna during device
long-term operation.
Antenna
Mount the supplied antenna on connector "LTE" of the MC92. Check whether there is sufficient local
network coverage from your mobile phone provider.
Inserting the SIM card
Insert your SIM card as shown in the figure below until it locks into place.
Power supply
The MC92 is operated with a supply voltage of 8 - 30V DC. Please connect an external DC power
supply with an output voltage of 8 - 30V DC to the power supply socket "PWR".
Please connect the power supply unit to the power supply or switch on the power supply. A green
"PWR" LED will light up.
After a short initialization phase (approx. 30 seconds) the device is ready for operation.
Configuration via Putty
1. In Putty, “Serial” as a Connection type.
2. Choose the right Serial port for your USB-RS232 connector.
3. Set the speed to "115200".
4. Expand the connection tab on the right side, then under “SSH” click on “Serial”.
5. Set "Flow control" to "None"
Configuration via Minicom
You can use the linux command line tool minicom to connect to the MC92.
1Using Command Prompt, give the command:
minicom --device /dev/ttyUSB0 --baud 115200,8,N,1
2Disable flow control by pressing CTRL+A followed by O to get into configuration. Then go
down to "Serial port setup", press "Enter" to enter and press "F" do toggle "Hardware
Flow Control"
The Modem will now respond to AT-Commands.
MC92
LTE Data-Gateway/Terminal
MC Technologies GmbH, Kabelkamp 2, 30179 Hannover, Germany
Tel: +49511 67 69 99-128, Fax: +49511 67 69 99-150, www.mc-technologies.net, www.mc-technologies.com, Email: [email protected]
3
AT Commands
AT commands for SIM presence and status
2.1.1 SIM Presence
1. Enable the extended error codes to get a verbose format:
AT+CMEE=2
OK
2. Now get the status of SIM presence:
AT+CPIN?
+CME ERROR: SIM not inserted
Above AT command response indicates that SIM card is not present.
3. Verify that SIM is inserted properly and check again:
AT+CPIN?
+CPIN: READY
OK
When the SIM card is ready, above AT response will be received from the module.
2.1.2 SIM PIN Status
1. Get the status of SIM PIN:
AT+CPIN?
Pin status can be:
READY: SIM PIN is already unlocked or lock has been disabled.
SIM PIN: This means SIM PIN is locked and code is required.
SIM PUK: Maximum number to retries to unlock has reached. PUK code is required from
network provider
2. If SIM PIN is required enter the following command to unlock the SIM:
AT+CPIN=”XXXX”
Enter the SIM PIN instead of XXXX
MC92
LTE Data-Gateway/Terminal
MC Technologies GmbH, Kabelkamp 2, 30179 Hannover, Germany
Tel: +49511 67 69 99-128, Fax: +49511 67 69 99-150, www.mc-technologies.net, www.mc-technologies.com, Email: [email protected]
4
GPS
2.2.1 Turn on and off the GNSS
Turn on GNSS function:
AT+QGPS=1
Turn off GNSS function:
AT+QGPSEND
Set GNSS function to turn on automatically:
AT+QGPSCFG="autogps",1
Wi-fi
2.3.1 Turn on and off Wi-fi
Turn on Wi-fi function:
AT+QWIFI=1
Turn off Wi-fi function:
AT+QWIFI=0
Wi-Fi Status
AT+QWIFI?
Altri manuali per MC92
1
Indice
Altri manuali MC Technologies Terminale touch
