Mechatronics Dominator BT Manuale utente
v 1.01
CONFIGURATOR
Dominator BT
User manual
v 1.01
Configurator Dominator BT
USER MANUAL
2
CONTENTS
1 General information 4
2 Installation 5
3 Operation 8
4 Settings 11
5 Calibration 14
5.1 Sensor calibration 15
5.2 Tank calibration 16
5.3 Sensor/tank calibration in inactive mode 19
6 Firmware update 21
7 Data logging 24
8 Additional information 25
8.1 Technical support 25
8.2 Contacts 25
Appendix I. Connecting Dominator BT to Teltonika FMB devices 26
Appendix II. Dominator BT message format 30
Appendix III. Status parameter 32
v 1.01
Configurator Dominator BT
USER MANUAL
3
TERMS AND DEFINITIONS:
FLS –eurosens fuel level sensor
App –application
Calibration –changing of sensor settings
PC –personal computer
v 1.01
Configurator Dominator BT
USER MANUAL
4
1GENERAL INFORMATION
_____________________________________________________________________________________
The application "Configurator Dominator BT" (app) is designed to calibrate,
monitor and test eurosens Dominator BT fuel level sensors (FLS) manufactured by
Mechatronics JSC.
To calibrate the sensor, you will need:
•Android Smartphone (ver. 9.0 or newer);
•Bluetooth ver. 4.2.
Configurator Dominator BT application will require to complete the
registration process. “Mechatronics” account will be created and stored
in Android Settings - > “Accounts” section.
It is not recommended to delete the program or account
“Mechatronics”, as this will lead to the loss of registration data, and you
will have to go through the registration process again. Update the app
over the installed version.
Bluetooth signal is stronger if the antenna icon on the sensor is directed
to receiver (fig. 1.1).
fig. 1.1. Antenna icon
v 1.01
Configurator Dominator BT
USER MANUAL
5
2INSTALLATION
_____________________________________________________________________________________
1. Download and install the application Configurator Dominator BT from
Play Market.
2. During the installation provide all required permissions to the app and
enable Bluetooth access and geolocation services (fig. 2.1).
fig. 2.1. Permissions
3. Start the app and follow the instructions.
4. During the first start fill in the registration form and sent it to Mechatronics
(fig. 2.2 and fig. 2.3).
v 1.01
Configurator Dominator BT
USER MANUAL
6
fig. 2.2. Filling in registration form
fig. 2.3. Sending registration form
v 1.01
Configurator Dominator BT
USER MANUAL
7
5. After the data has been verified by the manager, your account will be added
to the list of accounts in Android Settings - > “Accounts”.
6. Restart the app after you complete the registration process.
During the registration process, an Internet connection is required (to
send registration form and to poll registration server).
After the app is installed and registered, the configurator can work
offline.
v 1.01
Configurator Dominator BT
USER MANUAL
8
3OPERATION
_____________________________________________________________________________________
The FLS is supplied in an inactive state to save battery power.
1) After the application is installed and registered, check if the required
permissions, Bluetooth module and geolocation services are enabled.
2) Run the configurator.
3) Go to the tab “Messages” to monitor the current data being sent by the
sensor. The tab displays all the sensors found within the Bluetooth visibility
range as well as such devices as BT-COM, Dottrack, Degree BT.
4) Click the button “Clear”to clear the list and restart the search (fig. 3.1).
fig. 3.1. Current data
v 1.01
Configurator Dominator BT
USER MANUAL
9
5) Activate the settings mode of the sensor for further setup and calibration:
take the magnetic key from the sensor’s kit and apply it to the icon of magnet
on sensor’s case for 2-3 seconds (fig. 3.2) until the sensor appears in the tab
“Information”.
6) The activated sensor connects to a smartphone within 30 seconds and then
operates in settings mode until you exit the application or click the button
“Disconnect”.
fig. 3.2. Activation of settings mode
•If there have been more than three unsuccessful attempts to enter
the settings mode, then the next connection attempt will be
available in 10 minutes.
•If unsuccessful attempts and false connections continue, the sensor
will block the service connection for an hour.
•If there are no false connection attempts within 24 hours, the sensor
will reset the protection status.
7. After the device is connected, the tab “Information” will show sensor data:
the manufacturer, model and MAC address of the device, serial number and
firmware version, date of manufacture, battery status, temperature and
current detector values (fig. 3.3).
v 1.01
Configurator Dominator BT
USER MANUAL
10
fig. 3.3. Tab “Information”
Do not click the button "Switch to the firmware update mode" if the
update is not planned.
Leaving the sensor in the firmware mode can lead to a rapid discharge
of the battery (see part 6. Firmware update).
Indice
