Medeli DD620 Manuale utente

1Check the include items

Setup Guide

CYMBAL PADS BOX

Cymbal Pad for Hi-Hat Cymbal Pad for Crash(with Choke)

DRUM PADS BOX DRUM MODULE BOX

ACCESSORIES BOX

KICK PEDAL BOX

STAND AND CYMBAL HOLDER BOX

HI-HAT PEDAL BOX

WARNING:

Drum key can be pinched when adjusting clamps with drum key. Operate carefully.

Be careful around pipe ends, inside the pipe and screw ends. Metal shavings, etc. May injure your fingers.

Cymbal Pad for Ride

(with Chock)

(Dual Zone)

Pad Mount X 4 Drumsticks

Drum Key

Hi-Hat Holder

AC Adaptor

Owner’s Manual Setup GuideConnection Cable X 9

Screw X 3

Cymbal Holder x 3

Pillar (R1) Pillar (M1)

Pillar (L1)

Center Pipe (1)

Right Cross P ipe

Center Pipe (2)

Left Cross Pipe

Cymbal Rod Clamp

AFI

Foot Pedal

Beater

100

aw_DD620_Setup Manual_G01_150923_with kick peda

2015󾾠󾾠9󾾠󾾠23󾾠󾾠 11:47:56

2Set Up the Stand

Wing N ut 1

Wing N ut 2

7.Attach the pad mounts to the mount h olders on

the Center Pipe (1), Right Cross Pipe, and firmly

tighten the respective wing nuts 1.

8.Insert the two cymbal holders into the holders on

the Center Pipe (1) Clamp, attach the hi-hat holder

to mount holders on the Cymbal Rod Clamp, and

firmly tighten the respective wing nuts .

Note:

Loose n o r tighten the wing nuts on the mount

holder as shown partial enlargement.

Move the moun t holder s as needed, and firmly

tighten the respective wing nuts 2.

Note:

Loosen or tighten the wing nuts on the mount

holder as shown partial enlargement.

Right C ross P ipe

Cymbal R od C lamp

Center P ipe (1)

Wing N ut

Left C ross P ipe

Pillar (L1)

1.Attach the Center Pipe (2) to the clamp on the Pillar (L1) & (R1)

2.Attach the Left Cross Pipe to the clamp on the Pillar (M1)

3.Attach the Left Cross Pipe to the clamp on the Pillar (L1)

4.Attach the Right Cross Pipe to the clamp on the Pillar (R1) & (M1)

5.Attach the Cymbal Rod clamp on the Pillar (L1)

6.Attach the Center Pipe (1) to the clamp on the Pillar (L1) & (R1)

Note:

Loosen or tighten the screws on the clamp with drum key as shown partial enlargement.

A djust the height of the Right Cross Pipe and Center Pipe (1) with Wing Nuts as needed.

Pillar (R1)

Center Pipe (2)

Pillar (M1)

Wing N ut 1

Wing N ut 2

Wing N ut

100

aw_DD620_Setup Manual_G01_150923_with kick peda

2015󾾠󾾠9󾾠󾾠23󾾠󾾠 11:47:57

3Attach the Parts

Attach the Pads

1.Loosen the wing nuts on the drum pads.

2.Attach the drum pads to the pad mounts,

and firmly tighten the wing nuts on the

drum pads.

Wing Nut

Wing Nut 1

Tom 1 Tom 2

Snare Tom3

Wing Nut 1

Wing Nut 2

Attach the Cymbal Pads

Wing Nut 3

Felt Washer

Wing Nut 4

Cymbal Tilter

Attach the AFI

Insert the AFI position as shown.

1.Remove the wing nut and felt

washer from the cymbal tilter.

2.Place the cymbal pad, felt

washer, wing nut 3 assembly as

shown, and tighten the wing nut

3 to obtain an appropriate

amount of sway.

3.Adjust the cymbal pad position

with the wing nut 4.

Note:

Put the cymbal on the cymbal

adapter and locate the tap of

the adapter in the slot of the

cymbal bottom.

Hi-Hat

Crash

Ride

AFI

Attach the Drum Module

1.Push the cable into the mount holder slot on as shown.

2.Connect cable to the DB25 Jack on the back of drum module.

3.Attach the module to the mount holder on the , and

firmly tighten with the screws.

Center Pipe (1)

Note:

Adjust the drum module position by moving the mount holders as

needed, and firmly tighten the relevant wing nut.

AFI

100

aw_DD620_Setup Manual_G01_150923_with kick peda

2015󾾠󾾠9󾾠󾾠23󾾠󾾠 11:47:59

DD620_G01

Connection Procedure

1.Place the kick on the floor in the center of the rack as shown.

2.Place the hi-hat pedal on the floor on your left side.

3.Connect the pads to the drum module with the marked cables.

Are you ready? Let's enjoy playing it.

Make connections as shown in the illustration.

AFI AFI

Drum M odule

Tom 1 Tom2

Snare Tom3

Ride

Crash

Hi-Hat

HI-HAT C ontrol Kick P ad

Tom3

Snare

Tom2

Tom1

Ride

Crash

Drum

Module

Hi-Hat

Pedal

Kick

Pad

AFI AFI

Tom3

4Connect the Pads to the Drum Module

Folding Drum Rack

5Folding Drum Rack

Drum rack through five steps can be completed folding.

1.Adjust the snare position as shown in figure 1.

2.Loosen 4 wing nut as shown in figure 1, push pillar (M) in the direction

o f arrow to folde as shown in figure 2.

3.Push down S nare/TOM3 in the direction of arrow down to as shown in figure 3.

4.Turn back HI-HAT Cymbal in the arrow direction as shown in figure 3、4.

5.Push down T OM1/TOM2 in the direction of arrow down to as shown in

figure 5,Drum rack be completed folding.

345

Snare Tom3

Tom1 Tom2

Crash Ride

HI-HAT

Drum Module

AFI AFI

Wing N ut 1

Wing N ut 2

Wing N ut 3

Wing N ut 4

1.Loosen t he wing Nut 1 ~ 4 ,Pillar (M)

in the direction of arrow to

appropriate location

2.Clamp turn to position as shown in

figure 2 , Complete the drum rack

Unfolding D rum R ack

Wing N ut 1

Wing Nut 3

Wing Nut 4

Wing Nut 2

100

aw_DD620_Setup Manual_G01_150923_with kick peda

2015󾾠󾾠9󾾠󾾠23󾾠󾾠 11:48:02

Altri manuali per DD620

Indice

Altri manuali Medeli Tamburo

Manuali Tamburo popolari di altre marche

Yamaha

Yamaha RX-21 Manuale utente

Roland

Roland TD-9K Manuale utente

Sudoku

Sudoku LEXUS Manuale utente

Roland

Roland CR-80 Manuale utente

V-Drums

V-Drums V-Tour TD-9KX2 Manuale utente

Yamaha

Yamaha DTXPLORER Manuale utente

Cherub

Cherub WRW-206 Manuale utente

Opti-Med

Opti-Med JM-D1 Series Manuale utente

Roland

Roland CR-80 Manuale utente

Yamaha

Yamaha DTS70 Manuale utente

Yamaha

Yamaha DTXPRESS Manuale utente

Roland

Roland RM-2 Manuale utente

ATV

ATV aD5 Manuale utente

Alesis

Alesis DM Pro Kit Manuale utente

Roland

Roland TR-808 Manuale utente

Roland

Roland SPD-20 Manuale operativo e di manutenzione

Koma Elektronik

Koma Elektronik RH 301 Manuale utente

Roland

Roland TR-8 Manuale utente