meitav-tec MTSC Manuale utente
Touch Screen Thermostat
MTSC/SUPER/PPH
Owner’s manual and technician settings
-2-
-3-
Index
1. Owner’s Manual ………………………………………………..... 4
1.1 Quick Guide …………………………………………………. 4
1.2 Turning the unit ON or OFF ……………………………….. 5
1.3 Adjusting the set-point temperature………………………...5
1.4 Switching between Fan speeds……………………………..6
1.5 Timer for turning the thermostat off ………………………. 7
1.6 Economy mode indications E1 – E5 ….………………….. 8
1.7 Freeze protection ………………………...…………………. 9
2. Installation Instructions……..………………………………..... 10
3. Wiring Configuration and DIP Switches…….……………..... 13
4. Technician Settings …….……………………………………..... 20
5. MAC Address (MTSC Series only) ……………...…………..... 36
1. Owner’s manual
-4-
*Auto
speed
High Low
Press to switch between
fan speeds:
Med.
System ON
Set-point
adjustment
Temperature
scale
Ambient /
Set-point
temperature
display
Fan speeds
indication
Press to
turn
system
ON or OFF
*In Auto speed, the active
speed will appear
System OFF
1.1 Quick Guide
1.2 Turning the unit ON or OFF
Press the button to turn the unit ON – system mode and fan
speed symbols will appear on display.
Press again to turn the unit OFF – the symbols will disappear.
1.3 Adjusting the set-point temperature
While the thermostat is ON, press the or buttons – the
set-point temperature will flash.
Press again to adjust the set point.
Unit ONUnit OFF
-5-
1.4 Switching between fan speeds
Press the button to
switch between fan speeds:
Low
speed
Medium
speed
High
speed
Auto
speed
Note: When Auto speed Is
selected, the word “AUTO”
and the active fan speed
will appear on display
-6-
The selection of fan speeds may be disabled depending on system
configuration.
-8-
Economy mode can be activated by triggering a window contact,
door switch, key-tag or PIR sensor.
When Economy mode is active, the thermostat will either turn off or
use special economy set points for cooling and heating set by
technician.
Please refer to parameters P25 and P26 in the technician setting
section of this manual.
The following indications will appear on display:
-E1 – Economy mode triggered by window contact
-E2 – Economy mode triggered by PIR (occupancy sensor)
-E4 – Economy mode triggered by door switch or key-tag
-E5 – OFF state triggered by door switch or key-tag
-E6 – Valves OFF and Fan low triggered by door switch or key-tag
1.10 Economy mode indications E1 – E6
Temperature
Time
Normal work Freeze protection
Cut-in
Cut-out
The Freeze protection feature will not allow the room temperature to
drop below predefined cut-in temperature. Depending on which
configuration the system is operating under (with or without Heat pump)
this feature will force the system to operate in heat mode and activate
the fan.
This feature will take effect when the thermostat is either ON or OFF.
When the room temperature rises above the predefined cut-out
temperature, the thermostat will return to its previous state.
When freeze protection is activated, the display alternates between
“AL” and room temperature.
For selection of cut-in and cut-out temperatures, please refer to
technician settings parameters P36 and P37.
-9-
1.11 Freeze protection
2. Installation Instructions
-10-
The MTS/SUPER Thermostat designed for flush mounting in the room
to be controlled. It should be located where the occupant can easily
read the display and use the controls.
If the built in temperature sensor is being used to measure room
temperature, the panel should be placed where the temperature is
representative of the general room conditions, away from cold or warm
air draughts, radiant heat and direct sunlight.
The panel should not be installed on an outside wall.
- The standard installation height is 1.5 meter (5 feet) from the floor.
WARNING: Risk of Electric Shock and Property Damage.
Disconnect power supply before making electrical connections.
The installation is to be performed by a qualified electrician.
WARNING: The integrated circuits in the controller are
sensitive to static currents. Take suitable precautions.
2. Installation Instructions (cont’)
-11-
Installation procedure:
1. separate the front display from the back plastic cover by inserting a a
small flat screwdriver into each of the three slots as shown in the
picture and rotating it gently.
2. Remove the front display and keep it in a safe place.
3. Connect the wires as shown in the enclosed wiring diagram. All
terminals accept 1x0.5mm2/24 AWG.
4. If necessary, make changes to the DIP switches position as
explained in this manual.
5. Place the thermostat in the electrical box and tighten up the 2
screws Europe - Gewiss Box - GW 24 203 or similar
US - Carlon – B114R or similar or similar
6. Adapt the front frame-panel into its place, by pushing it towards the
wall.
Questo manuale è adatto per i seguenti modelli
2
Indice
Altri manuali meitav-tec Termostato
meitav-tec
meitav-tec ETN24-P-3S-HU Manuale utente
meitav-tec
meitav-tec ETNC24-FC-BAC-PIR-01 Manuale utente
meitav-tec
meitav-tec ETN24 Manuale utente
meitav-tec
meitav-tec BDIR Istruzioni utente
meitav-tec
meitav-tec FMH-220-HP11-3S-IR Manuale utente
meitav-tec
meitav-tec ETN-24-PM-H-1S Guida di sicurezza
meitav-tec
meitav-tec ETNC24-FC-BAC-PIR-02 Manuale utente
meitav-tec
meitav-tec ETN24-P-FC-SUPER2 Guida di sicurezza
meitav-tec
meitav-tec FMH-220 Fan-Coil Super 3 Manuale utente
meitav-tec
meitav-tec FMH-24-C2-3S-IR Manuale utente
meitav-tec
meitav-tec MTSC/SUPER/HU Manuale utente
meitav-tec
meitav-tec FMH-220-FAN-COIL-SUPER 3 Manuale utente
meitav-tec
meitav-tec ETNC24-SUPER-MDB-01 Manuale utente
meitav-tec
meitav-tec FMHC220-VFS-FC-MDB01 Guida
meitav-tec
meitav-tec FMH24-PD-1S-IR Manuale utente
meitav-tec
meitav-tec ETN-24-SUPER-PROG Guida di sicurezza
meitav-tec
meitav-tec ETN24-SUPER-SH-F Manuale utente
meitav-tec
meitav-tec Haften TRE24-PROG-HC11 Manuale utente
meitav-tec
meitav-tec ETN-24-SUPER-SI Series Manuale utente
meitav-tec
meitav-tec ETN-P Series Guida di sicurezza
