Melco EP 1 Manuale utente
Installation, Operation, and
Maintenance manual
for the EP 1
embroidery peripheral
• Single head, single needle
• Easy to operate
• Low power consumption
• High-quality results
Part Number 11034, Revision A
1575 West 124th Avenue
Denver, Colorado 80234
United States of America
© Copyright 1998 by Melco Embroidery Systems
ALL RIGHTS RESERVED No part of this publication may be reproduced, stored in a retrieval system,
or transmitted in any form or by any means (electronic, mechanical, photocopying, recording, or
otherwise) without prior written approval of Melco Embroidery Systems. Melco reserves the right
to revise this publication and to make changes in it at any time without obligation of Melco to
notify any person or organization of such revisions or changes.
All precautions have been taken to avoid errors or misrepresentations of facts, equipment, or
products. However, Melco does not assume any liability to any party for loss or damage caused by
errors or omissions.
Printed in the United States of America
Revision A, May 1998
Table of Contents
1. Setup
2. Needles, Bobbins, and Threads
Threading the EP1 2 - 1
Drawing Out the Bobbin Thread 2 - 3
The Bobbin Case 2 - 3
Removal 2 - 3
Winding Thread Onto The Bobbin Reel 2 - 4
Setting the Bobbin 2 - 4
Installation 2 - 5
Setting Thread Tensions 2 - 5
Upper Thread Tension 2 - 5
Bobbin Thread Tension 2 - 5
How to Select a Needle 2 - 6
Needle Replacement 2 - 6
3. Embroidery Hoops
Loading Garments 3 - 1
Round Hoops 3 - 1
Rectangular Hoops 3 - 1
Attaching The Hoop To The Pantagraph 3 - 2
4. Detailed Operation
The Control Panel 4 - 1
The Liquid Crystal Display (LCD) 4 - 1
Start Key 4 - 1
Stop Key 4 - 1
Arrow Keys 4 - 1
Hoop Center Key 4 - 1
Spool Key 4 - 1
Menu Key 4 - 1
Enter Key 4 - 1
Alt Key 4 - 2
The Light Emitting Diodes (LED) 4 - 2
The Operation Menus 4 - 2
Design Menu 4 - 2
Table of Contents
i
Run Design 4 - 2
Frame Menu 4 - 3
Trace Menu 4 - 3
Hoop Selection 4 - 3
Move Menu 4 - 3
Moving The Hoop Numerically 4 - 3
Seeing The Hoop’s Physical Location 4 - 3
Reset Menu 4 - 4
System Reset 4 - 4
Hard Reset 4 - 4
Other Functions 4 - 4
Thread Break 4 - 4
Bobbin Thread Low 4 - 4
Dust Accumulation 4 - 4
Upper Shaft Lock 4 - 4
Hoop Limits 4 - 4
5. Configuration
Unit Number 5 - 1
Display Brightness 5 - 1
Key Click Volume 5 - 2
Error Beep Volume 5 - 2
6. Operator Maintenance
Cleaning 6 - 1
Disassembling the Hook Area 6 - 1
Assembling the Hook Area 6 - 1
General Cleaning 6 - 2
Lubrication 6 - 2
Lubricating the Hook Area 6 - 2
General Lubrication 6 - 2
7. Troubleshooting Guide
Table of Contents
ii
iii
Single-Head Embroidery Peripheral
EP 1 Specifications
Maximum embroidery speed
1000 stitches per minute
Number of Heads
1
Number of needles
1
Dimensions
46cm W x 36cm H x 52cm D
18" W x 14" H x 20.5" D
Weight
26kg
58 lbs
Shipping weight
31kg
68 lbs
Power consumption
60 W; wired for 200V to 250V 50 or 60Hz
2 fuses, 800mA Fast Blow (FB)
Noise level and test conditions
Equivalent continuous A weighted sound pres-
sure level at 1 meter from the machine is 66db.
The peak C weighted instantaneous sound
pressure level is 71db.
The noise level was measured sewing a test
design at 600 spm.
Recommended power conditioning equip-
ment
LC 1800 Line stabilizer (available from
Accessory Resource Corporation)
Embroidering field size
24 x 14cm (9.5 x 5.5")
Compatibility
Premier, EDS-EZ, and EDS III
Intended use
The EP 1 is designed to embroider on textile
products which are placed easily in a Melco
embroidery hoop. The machine should not be
used on thick leather, wood, plastic, or other
dense material.
Table of Contents
iv
Explanation of Symbols
Caution!
Indicates a machine component will move. Keep clear!
Shock hazard. No user replaceable parts behind this label. Do not open!
Pinch point, Keep clear!
Pinch point, Keep clear!
Pinch points, Keep clear!
Needle pinch point, Keep clear!
1-1
1. Setup
The setup procedure for the EP 1 Embroidery Peripheral is easy and will only take a few minutes.
1. Carefully remove the machine from the shipping container, using care not to drop or damage
any other items packed around it. The machine is heavy, so be careful. Place the machine on a
sturdy table or work bench.
NOTE: Be sure to save the shipping container and packing supplies that your embroidery periph-
eral came in. If your machine should ever require factory service, it should be returned in
the original (or other equally suitable) shipping container.
2. Make certain the machine’s power switch is turned to the OFF position.
3. Plug one end of the power cord into a wall outlet. A
surge protector is recommended but not required.
Plug the other end into the machine.
4. Connect the peripheral to your controller or host
computer using the network cable. Plug the net-
work cable into either of the network ports, as
shown in Figure 1-1. Plug the terminator cable into
the other network connector. It does not matter
which cable is plugged into which connector.
5. Your machine may have come with a needle already
installed, but it is a good idea to start your sewing
with a new needle.
6. Locate the thread guide bar and gently pull it
upward until it reaches its maximum height. It will
extend like a car antenna. Rotate the guide bar until
the ends are aligned over the thread cones on the
base below (see Figure 1-2).
7. Your machine may have come with thread already
loaded on the bobbin, but check to make certain.
8. Load a spool of thread onto the thread stand and
thread the machine as required.
At this point your EP 1 should be ready to begin sewing.
If you should encounter any problems during this procedure, contact your local Melco representa-
tive for assistance, or call Melco’s Technical Support line.
11034 Rev. A 1. Setup
Figure 1-1
Network cable
Terminator cable
Figure 1-2
1-2
EP 1 Operation Manual Melco Embroidery Systems
Hazards of operation
Caution! Below are risk areas or danger points encountered dur-
ing operation. Always wear eye protection while operating the
machine to prevent injury in the event of a needle break. Do not
wear loose or baggy clothing when operating the machine.
Take-up Lever Oscillation
Do not touch the take-up levers during operation.
Exposed Needles During Operation
Do not place body parts or other foreign objects under the needles
during operation.
Rotary Hook Rotation
Do not attempt to change bobbin thread during operation. Do not
place hands or other objects in the rotary hook area during operation.
Do not operate the machine without the hook guards in place.
1-3
Dangers de service
Attention! Ci-dessous vous trouverez les descriptions de diverses zones
de risque ou points dangereux lors du service de la machine. Il faut tou-
jours porter des lunettes protectrices pendant le service de la machine
afin d'éviter des blessures en cas d'une casse d'aiguille.
11034 Rev. A 1. Setup
Oscillation du releveur de fil
Ne pas toucher les releveurs de fil pendant le service.
Aiguilles exposées pendant le service.
Ne mettre ni de parties du corps ni d'autres objets au-dessous
des aiguilles pendant le service.
Rotation de la navette rotative
Ne pas essayer de changer la canette pendant le service. Ne
pas mettre ni les mains ni d'autres objets dans la zone de la
navette rotative pendant le service. Ne pas mettre la machine
en marche sans avoir mis en place les gardes du ramasseur.
1-4
EP 1 Operation Manual Melco Embroidery Systems
Betriebsgefahren
Vorsicht! Nachfolgend sind Risikobereiche und Gefahrenpunkte genannt,
die während des Betriebs auftreten können. Tragen Sie immer einen
Augenschutz, wenn die Maschine in Betrieb ist, um Verletzungen im Falle
eines Nadelbruchs vorzubeugen. Tragen Sie keine weite oder lockere
Kleidung, wenn Sie die Maschine bedienen.
Hin- und Herbewegung des Fadengebers
Die Fadengeber nicht berühren, wenn die Maschine in Betrieb
ist.
Offenliegende Nadeln während des Betriebs
Körperteile fernhalten und keine fremden Gegenstände unter
die Nadeln legen, wenn die Maschine in Betrieb ist.
Umdrehung des Umlaufgreifers
Die Garnspule nicht austauschen, während die Maschine in
Betrieb ist. Die Hände vom Umlaufgreifer fernhalten oder
andere Gegenstände nicht in den Bereich des Umlaufgreifers
bringen, wenn die Maschine läuft. Die Maschine nicht bedi-
enen, wenn der Greiferschutz nicht an seinem Platz ist.
Indice
Altri manuali Melco Macchina da cucire
