Metapace S-61 Manuale utente

Disclaimer

Metapace reserves the right to make changes in speciﬁcations and other information

contained in this document without prior notice, and the reader should in all

cases consult seller to determine whether any such changes have been made.

The information in this publication does not represent a commitment on the part

of seller.

Seller shall not be liable for technical or editorial errors or omissions contained

herein; nor for incidental or consequential damages resulting from the furnishing,

performance, or use of this material.

This document contains proprietary information that is protected by copyright. All

rights are reserved. No part of this document may be photocopied, reproduced,

or translated into another language without the prior written consent of seller.

Table of Contents

iii

Table of Contents

Introduction .............................................................................................1

Components ..................................................................................................... 1

Maintenance..................................................................................................... 1

Caution and Serial Number Labels................................................................... 2

Cable Installation and Removal........................................................................ 3

Scanner Operation

Audible Indicators............................................................................................. 4

Visual Indicators ............................................................................................... 5

Failure Modes................................................................................................... 6

Typical Depth of Field....................................................................................... 6

Troubleshooting Guide...........................................................................7

Design Specifications ...........................................................................10

Configuration Introduction

Bar Code Configuration Methods ................................................................... 12

Single-Code Method.................................................................................... 12

Multi-Code Method...................................................................................... 12

Returning to Factory Defaults......................................................................... 13

Code Types and Decode Rules

2 of 5 Codes ................................................................................................... 14

Additional Decode Features ........................................................................... 14

Supplements..........................................................................................15

Scanner Operation

Redundant Scans........................................................................................... 16

Data Transmission Delays.............................................................................. 16

Laser/Scan Modes ......................................................................................... 16

Prefixes/Suffixes

User Configurable Prefixes, All Data .............................................................. 17

Standard Prefix Characters ............................................................................ 17

Standard Suffix Characters ............................................................................ 17

User Configurable Suffixes, All Data .............................................................. 18

Code Formatting

UPC/EAN Formatting ..................................................................................... 19

Keyboard

Enable Keyboard Emulation........................................................................... 21

Code Bytes Usage

Code Bytes 0-9............................................................................................... 23

Reserved Codes............................................................................................. 24

Code Type Table............................................................................................ 24

ASCII Reference Table................................................................................... 25

Extended Key Code Reference Table ............................................................ 29

Limited Warranty...................................................................................31

Standard Suffix Characters ............................................................................ 17

User Configurable Suffixes, All Data .............................................................. 18

Code Formatting

UPC/EAN Formatting ..................................................................................... 19

Keyboard

Enable Keyboard Emulation........................................................................... 21

Code Bytes Usage

Code Bytes 0-9............................................................................................... 23

Reserved Codes............................................................................................. 24

Code Type Table............................................................................................ 24

ASCII Reference Table................................................................................... 25

Extended Key Code Reference Table ............................................................ 29

Limited Warranty...................................................................................31

Introduction

Components

Item No. Description

1 Red Output Window (Laser Aperture)

2 Trigger

3 Pinhole for Cable Release (see page 3)

4 10-Pin RJ45, Female Socket

5 Beeper Hole

6 LED Indicator (see page 5)

Figure 1. Scanner Components

Maintenance

Smudges and dirt on the unit’s window can interfere with the unit’s performance.

If the window requires cleaning, use only a mild glass cleaner containing no

ammonia. When cleaning the window, spray the cleaner onto a lint free, non-

abrasive cleaning cloth then gently wipe the window clean.

If the unit’s housing requires cleaning, use a mild cleaning agent that does not

contain strong oxidizing chemicals. Strong cleaning agents may discolor or

damage the unit’s exterior.

Caution and Serial Number Labels

Figure 2. Label Location on the Bottom of the Scanner

Caution: To maintain compliance with applicable standards, all circuits connected to

the imager must meet the requirements for SELV (Safety Extra Low Voltage)

according to EN/IEC 60950-1.

To maintain compliance with standard CSA C22.2 No. 60950-1/UL 60950-1

and norm EN/IEC 60950-1, the power source should meet applicable

performance requirements for a limited power source.

Item Number,

Serial Number and

Compliance Information

location.

Cable Installation and Removal

Installation

1. Insert the cable’s modular connector into the socket on the scanner.

2. Pull gently on the cable strain relief to ensure the cable is installed.

Figure 3.

Removal

Turn off power to the host system before removing the cable from the scanner.

1. Locate the small pinhole on the

front side of the scanner near the

end of the handle.

2. Bend an ordinary paper clip into the

shape shown.

3. Insert the paper clip (or other small

metallic pin) into the small pinhole.

There will be a faint ‘click’ when the

connector’s lock releases.

4. Pull gently on the cable’s strain

relief to remove the cable.

Figure 4.

Scanner Operation

Audible Indicators

When the scanner is operational, the scanner provides audible feedback to

indicate the status of the scanner and the last scan. Eight settings are available

for the tone of the beep (normal, six alternate tones and no tone).

One Beep – On Power Up

When the unit powers up, the green LED turns on, then the red LED flashes and

the scanner beeps once. The red LED will remain on for the duration of the

beep. The scanner is now ready to scan.

One Beep – During Operation

When the scanner successfully reads a bar code, the red LED will flash and the

scanner beeps once (if programmed to do so). If the scanner does not beep

once and the red light does not flash, then the bar code has not been

successfully read.

Three Beeps – During Operation

When entering the configuration mode, the red LED flashes while the scanner

simultaneously beeps three times. The red LED continues to flash until the unit

exits configuration mode. Upon exiting configuration mode, the scanner beeps

three times and the red LED stops flashing.

When configured for communication timeout, three beeps during operation

indicates that a communication timeout has occurred.

Visual Indicators

The scanner is equipped with a red LED and green LED, which indicate the

scanner’s state and the status of the current scan respectively when the unit is in

operation.

Figure 5. LED Location

Green and Red LEDs Are Off

The LEDs will not be illuminated if the scanner is not receiving power from the

host or transformer.

Steady Green

Steady green indicates normal pulse or continuous laser operation.

Accompanied by a razzberry tone, a steady green LED indicates that an invalid

bar code has been scanned.

Flashing Green

After a period of inactivity, the ON time of the pulsing laser will be shortened.

During this time the green LED will flash. This indicates that the scanner is in a

power saver mode. When a bar code enters the laser field, the scanner will

wake up and return to normal pulse mode.

Steady Green and Single Red Flash

When the scanner successfully reads a bar code, the red LED will flash and the

scanner will beep. If the red LED does not flash and the scanner does not beep,

the bar code has not been successfully read.

Steady Green and Steady Red

After a successful read, the scanner transmits the data to the host device. Some

communication modes require that the host inform the scanner when data is

ready to be received. If the host is not ready to accept the information, the

scanner’s red LED will remain on until the data can be transmitted.

Steady Green and Continuous Flashing Red

When entering the configuration mode, the red LED will flash, the green LED will

turn on and the scanner will beep three times. The red LED will continue to flash

and the green LED will stay on until the unit exits the configuration mode.

LED

Failure Modes

One Razzberry Tone – On Power Up

This indicates the scanner has experienced a laser or flipper subsystem failure.

Return the unit for repair to an Authorized Service Center.

Continuous Razzberry Tone with no LEDs

If, upon power up, the scanner emits a continuous razzberry tone, then the

scanner has an experienced an electronic failure. Return the unit for repair to an

Authorized Service Center.

Three Beeps – On Power Up

If the scanner beeps three times on power up, then the non-volatile memory

(NovRAM) that holds the scanner configuration has failed. You must return the

unit for repair to an Authorized Service Center.

Typical Depth of Field by Bar Code Element Width

Bar Code Element

Width

Depth of Field

Start

(From Scanner Face)

End

(From Scanner Face)

0.13 mm 5.2 mil 76 mm (3") 127 mm (5")

0.19mm 7.5 mil 51 mm (2") 203 mm (8")

0.26 mm 10.4 mil 25 mm (1") 229 mm (9")

0.33 mm 13 mil 13 mm (0.5") 254 mm (10")

Indice

Altri manuali Metapace Lettore di codici a barre

Metapace

Metapace S-3 Manuale utente

Metapace

Metapace S-2 Manuale di istruzioni

Metapace

Metapace S-2 Manuale utente

Metapace

Metapace S-52 Manuale utente

Metapace

Metapace S-22 Manuale utente

Metapace

Metapace S-62 Manuale utente

Manuali Lettore di codici a barre popolari di altre marche

POSMicro

POSMicro Datalogic PowerScan D7100 Manuale utente

Marson

Marson MT780 Guida rapida alla configurazione

NCR

NCR RealPOS Manuale utente

Motorola

Motorola SE3300 Guida rapida alla configurazione

Element

Element P130BT Manuale utente

Motorola

Motorola Symbol LS3008 Manuale di installazione e funzionamento

Meec tools

Meec tools OBD-II / VAG Manuale utente

SICK

SICK CLP 100 Manuale utente

Royal Tag SA

Royal Tag SA I-Read Manuale utente

Welch Allyn

Welch Allyn IMAGETEAM 3800 Manuale utente

Meteor

Meteor 8310 Manuale utente

Denso

Denso BHT-500B Manuale utente

Datalogic

Datalogic Heron HD3130 Manuale utente

Motorola

Motorola MP6000 Istruzioni di montaggio

Newland

Newland NLS-HR15-BT Manuale utente

ARTDEV

ARTDEV AS-1310 Manuale utente

Aopos

Aopos AS290 Manuale utente

ENS

ENS 367-5455 Manuale utente