Metra Electronics 99-6536 Manuale utente

INSTALLATION INSTRUCTIONS

99-6536

Attention! Let the vehicle sit with the key

out of the ignition for a few minutes before

removing the factory radio. When testing the

aftermarket equipment, ensure that all factory

equipment is connected before cycling the

key to ignition.

KIT FEATURES

• ISO DIN radio provision with pocket

• ISO DDIN radio provision

•

Touchscreen display for climate and personalization features

•

Painted: Bronze - 99-6536BZ

Silver - 99-6536S

KIT COMPONENTS

• A) Radio trim panel with touchscreen display • B) Radio brackets • C) Pocket • D) (4) #8 x 3/8” Phillips screws • E) (10) Panel clips

• F) HVAC interface and wiring harness (not shown) • G) Antenna adapter (not shown)

TOOLS REQUIRED

• Panel removal tool • Phillips screwdriver

• 9/32” Socket wrench • 5.5mm socket wrench

TABLE OF CONTENTS

Dash Disassembly ..................................................2

Kit Preparation .......................................................3

Kit Assembly

–ISO DIN radio provision with pocket ..................4

–ISO DDIN radio provision .....................................4

Axxess Interface Installation ............................ 5-13

WIRING & ANTENNA CONNECTIONS

Wiring Harness: Axxess interface built into

touchscreen

Antenna Adapter: Included with kit

A B C D E

Jeep Grand Cherokee 2014-2017

Visit MetraOnline.com for more detailed information about the product and up-to-date vehicle

speciﬁc applications

1.800.221.0932

MetraOnline.com

DASH DISASSEMBLY

1. Unclip and remove the radio/climate

control panel. (Figure A)

2. Remove the (4) 9/32” screws securing

the radio/display screen, and then

unplug and remove. (Figure B)

3. Remove the (3) 5.5mm screws securing

the black control module in the

sub-dash, and then relocate lower to

allow clearance for the aftermarket

radio. (Figure C)

Continue to Kit Preparation

(Figure B)

(Figure A)

(Figure C)

REV. 11/26/2018 INST99-6536

KIT PREPARATION

(Figure A) (Figure B)

From the factory radio/climate control panel:

1. Unclip the vents from the back of the

panel. (Figure A)

To the 99-6536 radio trim panel:

1. Attach the vents to the back of the panel.

(Figure B)

2. Attach the (10)

panel clips

provided.

Continue to Kit Assembly

1.800.221.0932

MetraOnline.com

KIT ASSEMBLY

(Figure A)

(Figure B)

(Figure A)

ISO DIN radio provision with pocket

1. Attach the

pocket

to the

radio brackets

using the (4) #8 x 3/8” Phillips screws

provided. (Figure A)

2. Remove the metal DIN sleeve and trim

ring from the aftermarket radio.

3. Slide the radio into the bracket/pocket

assembly, and then secure it using the

screws supplied with the radio.

(Figure B)

Continue to Axxess

Interface Installation

ISO DDIN radio provision

1. Attach the

brackets

to the radio using

the screws supplied with the radio.

(Figure A)

Continue to Axxess

Interface Installation

REV. 11/26/2018 INST99-6536 5

AXXESS INTERFACE INSTALLATION

• Provides accessory power (12-volt 10-amp)

• Retains R.A.P. (retained accessory power)

• Provides NAV outputs (parking brake, reverse, speed sense)

• Retains audio controls on the steering wheel

• Retains safety chimes

• Retains the factory backup camera

• Retains the factory AUX-IN jack

• Retains balance and fade*

• Micro-B USB updatable

* Non-ampliﬁed models only.

INTERFACE FEATURES

• Crimping tool and connectors, or solder gun, solder, and heat shrink

• Tape • Wire cutter • Zip ties

TOOLS REQUIRED

• Axxess interface (built into the touchscreen display)

• 6536 harness

• 16-pin harness with stripped leads

• 4-pin harness with yellow RCA jacks

• Hazard harness

• Female 3.5mm connector with stripped leads

Connections ...............................................................................................................................6-8

Installation ....................................................................................................................................9

Programming ................................................................................................................................9

Final Assembly ..............................................................................................................................9

Touchscreen Display Operation .............................................................................................10-11

Steering Wheel Control Settings ...........................................................................................12-13

Troubleshooting ...........................................................................................................................13

INTERFACE COMPONENTS

TABLE OF CONTENTS

1.800.221.0932

MetraOnline.com

CONNECTIONS

From the 6536 harness to the aftermarket radio:

• Connect the Black wire to the ground wire.

• Connect the Yellow wire to the battery wire.

• Connect the Gray wire to the right front positive speaker output.

• Connect the Gray/Black wire to the right front negative speaker output.

• Connect the White wire to the left front positive speaker output.

• Connect the White/Black wire to the left front negative speaker output.

• Connect the (2) 4-pin connectors together.

• If retaining the factory backup camera, connect the Yellow RCA jack to the reverse

camera input.

• If the AUX-IN jack in the dash is desired to be used, connect the Red and White RCA jacks to

the audio AUX-IN jacks of the aftermarket radio.

• Disregard the DIN jack, it will not be used in this application.

Continue to 3.5mm jack steering wheel control retention

Attention! This interface will work with models that are either non-ampliﬁed, or ampliﬁed.

Please follow the instructions carefully for your model vehicle. Failure to do so will result in

either no sound, or low sound. If you are unsure if your vehicle is factory ampliﬁed or not,

please contact your local dealership.

For models

without

a factory ampliﬁer:

From the 16-pin harness with stripped leads to the aftermarket radio:

• Connect the Red wire to the accessory wire.

• If the aftermarket radio has an illumination wire, connect the Orange/White wire to it.

• Connect the Green wire to the left rear positive speaker output.

• Connect the Green/Black wire to the left rear negative speaker output.

• Connect the Purple wire to the right rear positive speaker output.

• Connect the Purple/Black wire to the right rear negative output.

• Tape off and disregard the following (6) wires, they will not be used in this application.

Blue/White, Brown, Gray, Gray/Black, White, White/Black

The following (3) wires are only for multimedia/navigation radios that require these wires.

• Connect the Blue/Pink wire to the VSS/speed sense wire.

• Connect the Green/Purple wire to the reverse wire.

• Connect the Light Green wire to the parking brake wire.

REV. 11/26/2018 INST99-6536

CONNECTIONS (CONT.)

The following (3) wires are only for multimedia/navigation radios that require these wires.

• Connect the Blue/Pink wire to the VSS/speed sense wire.

• Connect the Green/Purple wire to the reverse wire.

• Connect the Light Green wire to the parking brake wire.

From the 6536 harness to the aftermarket radio:

• Connect the Black wire to the ground wire.

• Connect the Yellow wire to the battery wire.

• Tape off and disregard the following (4) wires, they will not be used in this application:

Gray, Gray/Black, White, White/Black

• Connect the (2) 4-pin connectors together.

• If retaining the factory backup camera, connect the Yellow RCA jack to the reverse

camera input.

• If the AUX-IN jack in the dash is desired to be used, connect the Red and White RCA jacks to

the audio AUX-IN jacks of the aftermarket radio.

• Disregard the DIN jack, it will not be used in this application.

Continue to 3.5mm jack steering wheel control retention

Attention! This interface will work with models that are either non-ampliﬁed, or ampliﬁed. Please

follow the instructions carefully for your model vehicle. Failure to do so will result in either no

sound, or low sound. If you are unsure if your vehicle is factory ampliﬁed or not, please contact

your local dealership.

For models

with

a factory ampliﬁer:

From the 16-pin harness with stripped leads to the aftermarket radio:

• Connect the Red wire to the accessory wire.

• Connect the Blue/White wire to the amp turn on wire. This wire must be connected to hear

sound from the factory ampliﬁer.