Miccus MHRTX-20 Manuale dell'operatore
Miccus® Home RTX 2.0
Long Range Wireless Audio
TransmierorReceiver
Model No.: MHRTX-20
Quick Start Guide:
1. Aachtheantenna:On the back of the Home RTX 2.0, remove
the white cover and aach the antenna. Turn clockwise unl
slightly snug. Posion the antenna upright.
2. Connecttheaudio:Connect the appropriate included cable
(Opcal/TOSLINK or RCA to 3.5mm) to the appropriate audio
input (TX mode only) or output (RX mode only) on the back of
the RTX 2.0.
3. Poweron/o:Connect the micro end of the USB cable to the
RTX 2.0 and the other end to any USB port or 5v/500mA USB
power supply; the Home RTX 2.0 will automacally power on.
If powered o, the Home RTX 2.0 can be powered back on by
holding the mul-funcon buon for 5 seconds unl the LED
indicators power on.
4. Pairing:
1. Set the selector switch to TX (transmit mode), or RX (receive
mode)
2. Place your Bluetooth® receiving or transming device into
pairing mode.
3. Place the Home RTX 2.0 into pairing mode by pressing the
mul-funcon buon for 3 seconds unl a unl a channel (CH)
blue light begins ashing rapidly. This indicates pairing mode.
4. Once paired the CH LED light will change to either solid blue or
blink twice every 5 seconds if connected in aptX Low Latency.
Note: if your phone or tablet requires a passkey use: 0000
CH1 or CH2 LED Funcon
Rapidly Flashing Blue Pairing mode
Solid Blue Connected with SBC or aptX
codecs (slight delay)
2 blue blinks every 5 seconds Connected with aptX Low
Latency codec (no delay)
1
AbouttheMiccus®HomeRTX2.0
The Miccus® Home RTX 2.0 is the world’s rst dual link long range
wireless transmier or receiver featuring Bluetooth® v4.2 and two
simultaneous aptX Low Latency audio streams. Use as either a
Bluetooth® receiver or transmier and add Bluetooth® technology
to your exisng television or stereo equipment. The Home RTX 2.0
supports dual link pairing; which means two devices can be paired at
the same me. The Home RTX 2.0 also features opcal audio pass
thru. Use the same audio source and daisy chain two or more Home
RTX 2.0’s together; double or even triple the number of low latency
audio streams available for use. Avoid the use of an opcal splier
box; use the digital audio pass thru of the Home RTX 2.0 to send
television audio to both the RTX 2.0 and your soundbar.
What’sintheBox?
2
A. Miccus® Home RTX 2.0
B. Dipole Antenna
C. Opcal/TOSLINK digital
audio cable
D. 3.5mm male to 3.5mm male
Audio Cable
E. Micro USB charging cable
F. USB Power Supply
G. User Manual
System Requirements
The Miccus® Home RTX 2.0 transmits or receives high quality stereo
audio paired with any compable A2DP Bluetooth® prole transming
or receiving device.
Transmit Mode (TX): Use the RTX 2.0 with any device capable of
Receiving a Bluetooth® wireless audio signal (A2DP), including
Bluetooth® enabled headphones, speakers or adapters such as the
Miccus® Home RTX 2.0, Swivel Jack RTX, Home RTX Mini, and SR-71
Stealth Headphones.
ReceiveMode(RX): Use the RTX 2.0 with any device capable of
Transming a Bluetooth® wireless audio signal (A2DP). Such capable
devices include phones, tablets, and adapters such as the Miccus®
①
Antenna
②
CH1 Indicator (blue)
③
CH2 indicator (blue)
④
Opcal Indicator
⑤
3.5mm Indicator
⑥ 3.5mm audio output
⑦ Opcal audio output (TOSLINK)
⑧
Antenna Connector
⑨
USB
⑩
Opcal audio input (TOSLINK)
⑪
3.5mm audio input
⑫
RX/TX Mode
3
GengAquainted
❶
❸
❻ ❼
❽
❾ ❿ ⓫ ⓬
❺
❷ ❹
4
Home RTX, Home RTX Mini, Mini-jack TX4, and Mini-jack RTX.
Bluetooth®CodecSupport: The Miccus® Home RTX 2.0 provides support
for four common Bluetooth® audio codecs: SBC, AAC, aptX, aptX Low
Latency. The Home RTX 2.0 will automacally pair at the highest quality
common codec that both devices support.
UsewithTV:aptXLowLatencycodec
aptX Low Latency codec requires that both the transmier and receiver
support aptX Low Latency. If you use the RTX 2.0 with Bluetooth
headphones that do not support aptX Low Latency, the 2.0 will default
to the standard aptX or SBC codec. If TV or video audio is your primary
use, consider purchasing Bluetooth headphones that support aptX Low
Latency like the Miccus Stealth SR-71 Headphones.
When paired with two sets of aptX Low Latency headphones, the Home
RTX 2.0 will stream in aptX Low Latency to BOTH headphones, unlike
other adapters that drop the aptx LL codec in dual link mode.
OtherEndBluetoothDevice Audio Latency
aptX Low Latency 38ms (+ or – 5ms)
aptX 70ms (+ or – 10ms)
SBC 220ms (+ or – 50ms)
LEDIndicatorLightGuide
The Home RTX 2.0 communicates with you via LED indicator lights.
Following is a brief descripon of what each means. Refer to this guide
as needed while reading the manual and working with your new RTX 2.0.
LIGHT FUNCTION
LED solid blue CH 1/CH 2 pair acve
LED blinks blue rapidly Pairing mode
LIGHT FUNCTION
LED solid green Opcal or 3.5mm acve
CH 1 and CH 2 blue LED o
or blinking slowly Standby Mode (no pairing detected)
LED solid blue Connected with either the SBC or
aptX codecs
LED blue stays on with 2
blinks every 5 seconds Connected with the aptX Low
Latency codec
DetailedInstruconsforUse
Aachtheantenna
On the back of the Home RTX 2.0, remove the white cover and aach the
antenna. Turn clockwise unl slightly snug. Posion the antenna upright.
Connect Power Cable
The RTX 2.0 is powered only by micro USB power; there is no baery
to charge.
Connect the micro end of the included USB power cable to the RTX 2.0’s
micro USB jack; connect the other end to the compable USB power
supply unit (5V/500mA), computer, or television USB port.
For opmal performance, always use the provided USB cable which
features a ferrite core to help eliminate radio frequency interference
during operaon. While any USB charger that is rated at an output of
5V@500MA or higher is compable, you may experience buzzing or
less signal range while using another USB cable.
The USB power cable only supplies power, it does not connect audio.
Connect Audio Cable
To connect the RTX 2.0 to other audio devices to receive or transmit
audio, Miccus has included 2 audio cable opons to select from
dependent on your audio needs. You will only need 1 audio cable to
connect the audio.
5
a) TOSLINK digital opcal cable
b) 3.5mm (mini-plug) male to 3.5mm (mini-plug) male cable
Note: If your TV or stereo system requires a dierent cable, please
contact Miccus Customer Support and we may be able to help you:
[email protected], 616-604-4449.
To transmit in TX (transmit) mode, the RTX 2.0 must be connected to an
audio source with audio to transmit such as a TV, stereo, computer,
tablet, or phone etc.
1. Determine which cable is needed by your audio source (your TV,
stereo, etc.)
2. Connect the appropriate cable to the auxiliary output on your
audio source (your TV, stereo, etc.)
3. Connect the other end of the cable to the back of the RTX 2.0
“From TV” label, either TOSLINK / opcal to the “Opcal In” or
3.5mm to the “3.5mm In.”
To receive in RX (receive) mode, the RTX 2.0 must be connected to a
stereo or powered speaker system to receive audio on.
1. Determine which cable is needed by your stereo or powered
speaker system’s auxiliary input: either TOSLINK/opcal or
3.5mm.
2. Connect the appropriate cable to the auxiliary input on your
stereo or powered system
3. Connect the other end of the cable to the back of the RTX 2.0
“To Speaker” label, TOSLINK/opcal to the “Opcal Out” or
3.5mm to the “3.5mm Out.”
PowerOn/O
There are three ways to power on the RTX 2.0:
1. Connect the RTX 2.0 to USB power and it will automacally
power on
6
2. If already connected to USB power and powered o, press and hold
the power buon for 5 seconds unl the indicator lights come on
3. If o, switching the RTX 2.0 between TX and RX modes will
automacally power it on
To power o the RTX 2.0: press the mul-funcon buon for
approximately 6 seconds unl the 2.0 powers down.
Pairing
The pairing process creates a Bluetooth bridge between a Bluetooth
transmier and a Bluetooth receiver. The versale Home RTX 2.0 can
funcon as either a Bluetooth transmier OR receiver. The pairing
process should take no more than 5-10 minutes.
For quicker, easier pairing:
• Verify the RTX 2.0 has power and audio connecons completed
(see above)
• Make sure the RTX 2.0 and your Bluetooth® device are physically
located near each other during the pairing process, no more than
3 apart.
• Make sure any previously paired devices, Bluetooth headphones,
speakers, adaptors are turned o so the Home RTX 2.0 is ready to
look for a NEW device to pair to.
• Please follow the below steps in a mely manner, without
interrupons for best results.
Transmit Mode (TX):
1. Locate the RX/TX switch on the back right of the Home RTX 2.0.
Select TX mode by pressing the buon into the “In” posion.
2. Verify that the audio cable is connected in the “From TV” label on
the back of the RTX 2.0, either the 3.5mm audio input or the
TOSLINK/opcal audio input.
3. Power on and start the pairing mode on your receiving device, i.e.
Bluetooth enabled headphones, speaker or other compable A2DP
Bluetooth® prole device.
4. Power on the RTX 2.0. There are three ways to power on the
Home RTX 2.0: 1) connect the RTX 2.0 to USB power, 2) If already
7
connected to USB power and powered o, press and hold the
power buon for 5 seconds unl the indicator lights come on, 3) In
the o posion, switch the RTX 2.0 between TX and RX mode.
5. Start the pairing mode on the RTX 2.0: press and hold the
mul-funcon/power buon for 3 seconds unl the CH 1 light
begins ashing rapidly.
6. WAIT for the devices to connect. This may take up to 30 seconds.
7. Once paired, the Home RTX 2.0 CH 1 indicator light will change to
either solid blue or blink twice every 5 seconds if in Low Latency
codec.
8. To begin streaming music wirelessly, simply press the play buon
on your audio source, adjust the volume as needed and enjoy!
9. If you want to pair to a second device, follow these steps:
1. Pair your rst Bluetooth receiving device (headphones or
speakers) to the Home RTX 2.0. (steps 1-8 above)
2. Start the pairing mode on the RTX 2.0 by pressing the
mul-funcon buon for 3 seconds unl the CH 2 light begins
ashing rapidly.
3. Wait for the devices to connect. This may take up to 30 seconds.
4. When the second set is paired, both CH 1 and 2 lights will light
either solid or will blink twice every 5 seconds indicang aptX
Low Latency codec.
Pairing Mode (RX):
To make the pairing process easier in RX mode, Miccus has added
friendly voice prompts to communicate the status. From your speaker or
headphones, throughout pairing and use you will hear:
• Power On – Home RTX 2.0 has been turned on
• Pairing – Home RTX 2.0 is looking for a device to pair to
• Connected – Your devices are connected and ready to use
• Disconnected – Your devices are no longer connected or paired
• Power O – RTX 2.0 is o
1. Locate the RX/TX switch on the back right of the Home RTX 2.0.
Select RX mode by pressing and releasing the switch to the “Out”
posion.
8
2. Verify that the appropriate audio cable is connected in the “To
Speaker” label on the back of the RTX 2.0, either the 3.5mm audio
input or the TOSLINK/opcal audio input.
3. Power on the Home RTX 2.0. There are three ways to power on the
Home RTX 2.0: 1) connect the RTX 2.0 to USB power, 2) If already
connected to USB power and powered o, press and hold the
power buon for 5 seconds unl the indicator lights come on,
3) If powered o, switch between TX and RX mode
4. Start the pairing mode on the RTX 2.0: press the mul-funcon
buon for 3 seconds unl the CH 1 light begins ashing rapidly.
You will hear a voicing announcing “Pairing.”
5. Open the Bluetooth menu on your phone, tablet or other
compable A2DP Bluetooth® prole device and select the Miccus
Home RTX 2.0. If your tablet or cell phone requires a passkey, use
“0000.”
6. WAIT for the devices to connect. This may take up to 30 seconds.
7. Once paired, you will hear a voice announcing “Connected” and
the Home RTX 2.0 CH1 indicator light will change to either solid
blue or blink twice every 5 seconds if in Low Latency mode.
8. To begin streaming wireless audio, simply press play on your audio
source, adjust the volume to preference, and enjoy!
9. If you want to pair to a second device, follow these steps:
1. Pair your rst phone or tablet to the Home RTX 2.0 (steps 1-8
above)
2. Start the pairing mode on the RTX 2.0 by pressing the
mul-funcon buon for 3 seconds unl the CH 2 light begins
ashing rapidly
3. Open the Bluetooth menu on your phone, tablet or other
compable A2DP Bluetooth® prole device and select the
Miccus Home RTX 2.0. If your tablet or phone requires a
passkey, use “0000.”
4. Wait for the devices to connect. This may take up to 30
seconds.
5. When the second set is paired, both CH 1 and 2 lights will light
either solid or will blink twice every 5 seconds indicang aptX
Low Latency codec.
9
Indice
Altri manuali Miccus Trasmettitore
