Midea VCP6P Manuale utente

This manual is for reference only, the information has

been carefully checked, if there are any discrepancy, the

factory specifications shall prevail

Quick Start Guide

Cordless Cyclone Vacuum Cleaner

VCP6P

Main unit

Extension tube

Flat nozzle

Electric bed brush

When cleaning high places, accessories can be installed on the extension tube.

Manual

2-in-1 brush Storage buckle

assembly

Storage base

assembly

Power adapter

Electric floor brush

Product Introduction

Installation and component introduction

Parts List

Tips

1. Before placing the machine on the storage rack or when the storage rack is left alone,

be sure to place it on a horizontal surface to avoid falling and damaging the machine;

2. Whether the machine is at work or placed on a storage rack, it must be handled

gently to avoid damage;

1. Installation of storage rack:

Install the storage buckle assembly and storage base as shown in the figure, and

place the assembled storage rack assembly vertically on the horizontal surface as

shown on the right;

Functional Operation

Installation and use of storage rack

Note

2. Placement of the machine:

Before placing the machine on the storage rack assembly, please confirm whether

the placement position is horizontal, and make sure that the machine is turned off

and stopped working. Place the machine on the position of the storage rack gently as

shown in the figure below and leave after the machine is stable.

Functional Operation

Installation and use of storage rack

1. The battery is not charged when shipped from the factory. Please be sure to fully

charge it before use;

2. Do not charge in the environment below 5°C or above 40°C;

3. If the battery power is insufficient during operation, the battery power indicator will flash;

4. When the battery life of the machine becomes significantly shorter and the charging

time becomes longer, please ask qualified personnel to replace the battery. Do not

disassemble the machine yourself in order to avoid danger;

Place the main unit on the storage base smoothly;

Charging time: 4-6 hours

Discharge time: Up to 10 minutes for high power, about 20 minutes for medium

power, and about 1 hour for low power.

Connect one end of the power cord to the socket, and the other end to the

charging port at the end of the battery pack of the main unit. The power

indicator flashes. After the battery is fully charged for a period of time, the

indicator turns off;

Functional Operation

Battery charging

Note

No. Instructions

Indicator light Switch

button

Speed button

LED1

(battery

indicator)

LED3

(speed control

indicator)

LED2

(battery indicator)

Speed button

Switch button

Press the “Switch” button once to start cleaning;

Press the “Switch” button again to stop cleaning;

Battery indication when working (discharging): When LED1 and LED2 are

on, the battery power is sufficient. When LED1 flashes or LED2 turns off,

the battery power is low and needs charging.

When LED1, LED2 and LED3 are all flashing, it indicates an alarm; please

ask qualified personnel to repair;

The default mode is medium power (LED1, LED2 and LED3 are all on)

when power is full; when the “Speed” button is pressed once, it enters high

power (LED1 and LED2 on, LED3 blue); when the “Speed” button is

pressed again, it enters low power (LED1 and LED2 on, LED3 off);

Battery indication when charging: When LED1 or LED2 flashes, the battery power

is low, and the battery needs charging. When both LED1 and LED2 are on, the

battery power is full, and the indicators will turn off after a period of time.

1. To avoid blocking the air duct, please clean up large pieces of garbage in the area

first (such as large pieces of paper, packaging film, etc.);

2. Do not use and store the battery in an environment below 5°C or above 40°C;

3. When disposing of this product, please remove the battery from the machine;

4. It is strictly prohibited to modify the machine, accessories and adapter.

Functional Operation

Clean up

Note

No. Instructions

Take out

Press

To maintain the suction power of the vacuum cleaner, please clean the dust regularly.

Dust cup disassembly

Place the machine flat as shown, press the main lock button with one hand and take out

the dust cup assembly with the other hand.

Dust cup cleaning

Method 1:

Keep the machine body vertical, press the

button, open the lower cover of the dust

cup and pour the dust;

Method 2:

Remove the dust cup as shown in the

figure above, and then press the bottom

cover of the dust cup to pour the dust.

Cleaning and Maintenance

Dust cup disassembly and cleaning

Note

1. The parts in the dust cup are washable;

2. Please make sure that all parts are dry before cleaning and installing them back.

1. Hold the ribs on both sides with your

hands, and gently remove the filter

assembly from the dust cup assembly;

3. After removing the filter assembly, rotate and remove the cyclone as shown in the

figure to clean it. After fully drying, install it back according to the disassembly steps.

Filter

assembly

Uninstall Install back

Filter sponge

Cyclone

assembly

2. Take out the filter sponge and cyclone

components in turn;

Cleaning and Maintenance

Filter disassembly and cleaning

Note

1. Press the button to remove the electric floor brush;

2. Unscrew the roller brush gland according to the instructions, lift the roller brush gland

upward, remove the roller brush for cleaning, and follow the disassembly steps to

install it back after cleaning.

Press

Remove the roller brush gland Remove the roller brush

Cleaning and Maintenance

Disassembly and cleaning of electric floor brush

1. In order to avoid affecting the operation of the electric floor brush, please clean and

maintain it when the roller brush or wheels are tangled or dirty.

2. Before disassembling and maintaining, be sure to stop the operation of the electric

floor brush;

3. It is not recommended to wash the floor brush. The tangled hair can be cleaned with

scissors or a blade, and the dust stuck to the roller brush can be cleaned with a brush.

Note

1. Press the button to remove the

electric bed brush;

3. Wrap disposable chopsticks with paper towels or cloth strips and wipe the inside. If

the roller brush is tangled by hair, use scissors to cut along the roller brush, and then

clean it. After cleaning, follow the disassembly steps above to install it back.

2. Pull out the buckle as shown in the figure

below, and then rotate to remove the

bottom plate;

Pull down

Cleaning and Maintenance

Electric bed brush cleaning

1. When the dust blocks the air duct of the electric bed brush, please use disposable

chopsticks to remove it;

2. Except for the bottom cover, the brush can’t be washed with water;

3. During operation, do not touch the roller brush that rotates at the bottom;

4. To avoid affecting the operation of the electric bed brush, please perform cleaning

and maintenance when the roller brush is tangled or dirty.

Note

Indice

Altri manuali Midea Aspirapolvere

Manuali Aspirapolvere popolari di altre marche

Bissell

Bissell LittleGreen Proheat 1425 Series Manuale utente

Panasonic

Panasonic MC-YL637S147-AE Manuale utente

NEFF

NEFF N17XH10 0 Series Manuale utente

LG A9 Series Manuale utente

Oreck

Oreck Cordless Captura BK51700 Series Manuale utente

Kogan

Kogan KAVACROBVWA Manuale utente

Kränzle

Kränzle VENTOS 50 ID Guida utente

EVVO

EVVO Ai35 Manuale utente

DeWalt

DeWalt DWH200D Manuale utente

Pontec

Pontec Pondomatic Vacuum Cleaner Manuale utente

Cleanmaxx

Cleanmaxx PC-P007E Manuale utente

Exido

Exido 240-114 Manuale utente

RIDGID

RIDGID WD1685AU0 Manuale utente

Ezviz

Ezviz RE4P Manuale utente

STG global

STG global TANVAC HDV3000 Manuale utente

Shark

Shark ROTATOR PRO COMPLETE NV550 Series Manuale utente

Factory

Factory M3340 Manuale utente

Shop-Vac

Shop-Vac VN92 SERIES Manuale utente