MIMAKI UJF-605CII Manuale utente

MIMAKI ENGINEERING CO., LTD.

TKB Gotenyama Building, 5-9-41, Kitashinagawa, Shinagawa-ku, Tokyo 141-0001, Japan

Phone: +81-3-5420-8671 Fax: +81-3-5420-8687

URL: http: // www.mimaki. co. jp /

E-mail: [email protected]

Daily Care Manual

D201579

Request for daily care

Inkjet printer is the precision machine that has highly delicate mechanism. Especially, little dust and

paper powder may have effect on a head nozzle firing ink, and may not get normal printing.

To use the inkjet printer in good condition, we recommend the following daily care.

Table of contents

In Case Sefective Printing Is Not Resolved ............................................ 5

Cleaning Flushing Tray ............................................................................ 8

When The Waste Ink Tank Becomes Full.............................................. 10

Replacing Water In Water Heater Tank ................................................. 11

Regular Maintenance For White Ink ...................................................... 17

Cleaning Or Replacing Filter ................................................................. 19

Cleaning The Undersurface Of The Carriage........................................ 20

Storage Of Antifreezing Liquid And Washing Liquid.............................. 22

Storage Of Media .................................................................................. 22

Storage Of Ink Cartridge ....................................................................... 22

Installation environment and Notes on cleaning

•Use this printer in clean (less dust) environment. The use of fan and ventilator might be

cause of dusty environment.

They brow dust up dust around the printer.

•As using UV curing ink, install this printer in a well-ventilated area.

•Working environmental temperature is 15 to 30°C (59 to 86°F). Avoid using at lower or

higher than this.

Notes on cleaning

•Never disassemble the device. Disassembling the device can result in

electric shock hazards and breakage of the device.

•Prevent moisture from entering inside the device. If the inner part of the

device becomes wet, electric shock hazards and breakage of the device

can result.

•Conduct maintenance works after turning off the power switch and detach-

ing the power cable. If not, unexpected troubles can arise.

•Make maintenance after the UV lamp has been sufficiently cooled, or burn

injury may occur.

•Do not use benzine, thinner and chemical agents containing abrasives.

Such materials can deteriorate or deform the surface of the cover.

•Do not apply lubricating oil or the like inside the device. Such materials

can cause the printer mechanism to fail.

•UJF-605C is a printer that uses ultraviolet ray curing ink (UV ink).. When

implementing the daily care, must wear supplied goggles and gloves.

•In case water or alcohol mixed into the organic solvent ink, flocculation

would be occurred. Be sure that not adhere water or alcohol to not only the

nozzle and also near the head, the cap, wiper and so on.

Maintenance for frame components

If the frame components of the device have stained, dampen a piece of soft cloth with

water or neutral detergent diluted with water, squeeze it and wipe the frame components

clean.

In Case Sefective Printing Is Not Resolved

When the station interior is severely contaminated or defective printing is not resolved

after executing the head cleaning function ( Operation manual P.2-20).

Clean the suction nozzle and cap using the cleaning kit as follows,

Washing liquid, Gloves, Cleaning swab, goggles

•When cleaning the ink station and head, be sure to wear the supplied

goggle and gloves since you may get ink in your eyes.

•Do not use alcohol or water.

•Do not move the carriage out of the capping station by hand. Use the

appropriate operation key to move the carriage.

The examples of defective printing

These following examples indicate improper head (nozzle) firing by dust, which effect

printing. Confirm the nozzle condition periodically before or during outputting not to use in

such as this condition. The nozzle condition can be confirmed with [test print] in this plotter.

Deflection Nozzle out

Ink dropping Satellite

STEP

1. Press the [FUNCTION] key from the LO-

CAL mode.

2. Press the [ ] and [ ] keys until the display

gives the indication [MAINTENANCE].

3. Press the [ENTER] key.

4. Press the [ ] and [ ] keys until the display

gives the indication [STATION].

5. Press the [ENTER] key.

6. Press the [ENTER] key again.

Carriage moves to the table.

7. Open the right maintenance cover.

8. Clean the suction nozzle using the exclu-

sive cleaning swab which is containing

washing liquid.

•Carefully clean the suction nozzle.

•Suction nozzle severely contaminated

or bent should be replaced with a new

one. Contact your nearest sales

agency or Mimaki sales office.

•Contact your nearest sales agency or

Mimaki sales office to order the exclu-

sive cleaning swab.

<< LOCAL >>

STATION

CARRIAGE OUT : ent

MAINTENANCE

STATION < ent >

MAINTENANCE

LIST < ent >

FUNCTION

MAINTENANCE < ENT >

FUNCTION

DATA CLEAR < ENT >

9. Wipe the adherent ink which got on the

cap rubber or inside the suction nozzle

cover with the exclusive cleaning swab.

10. Close the maintenance cover and then press

the [ENTER] key.

The initial operation is performe, then the device

enters to the LOCAL mode.

How to recover improper nozzle firing

When not using this plotter for a long time or according to environmental temperature,

nozzle may be unstable in firing.

In the case of this, follow below procedures to recover nozzle.

In case the nozzle doesn't recover after implementing these procedures, contact with our

customer service or agency you purchased, and need to replace heads and so on.

1. Daily care

Implement all parts noted on this article.

2. Normal cleaning ( Operation manual

P.2-20)

Implement normal cleaning along the instruction

manual after daily care above-mentioned.

Repeat cleaning and test printing, and confirm the

nozzle still clogging or not.

•In case nozzle clogging is not resolved

with all these procedures, contact with

our customer service or make service

call to the agency you purchased.

Suction nozzle cover

STATION

COMPLETED : ent

PLEASE WAIT

<< LOCAL >>

Cleaning Flushing Tray

Wipe off waste ink from the flushing tray.

Tools necessary for cleaning: Washing liquid, Gloves, goggles, paper towel

•When cleaning the ink station and head, be sure to wear the supplied

goggle and gloves since you may get ink in your eyes.

•Do not move the carriage out of the capping station by hand. Use the

appropriate operation key to move the carriage.

•Make sure to remove the waste ink in the flushing tray frequently. Other-

wise the waste ink dried out solidly under the UV light and may not remove.

STEP

1. Press the [FUNCTION] key from the LO-

CAL mode.

2. Press the [ ] and [ ] keys until the display

gives the indication [MAINTENANCE].

3. Press the [ENTER] key.

4. Press the [ ] and [ ] keys until the display

gives the indication [STATION].

5. Press the [ENTER] key.

6. Press the [ENTER] key.

Carriage moves to the table.

<< LOCAL >>

STATION

CARRIAGE OUT : ent

MAINTENANCE

STATION < ent >

MAINTENANCE

LIST < ent >

FUNCTION

MAINTENANCE < ENT >

FUNCTION

DATA CLEAR < ENT >

7. Open the left maintenance cover.

8. Wipe off the waste ink from the flushing

tray with the paper towel containing wash-

ing liquid. Take the caked ink off by pat-

ting the tray.

•Make sure to take the caked ink off

completely, or it may cause head

damage by the remaining caked ink.

The UV ink dried out solidly under the

UV light. In case unable to get rid of

the caked ink, the tray should be

replaced with a new one. Please

contact your local dealer for purchas-

ing a new tray.

9. Close the station cover and then press the

[ENTER] key.

The initial operation is performe, then the device

enters to the LOCAL mode.

STATION

COMPLETED : ent

PLEASE WAIT

<< LOCAL >>

When The Waste Ink Tank Becomes Full

Waste ink used for cleaning the heads will gather in the waste ink tank.

•Contact your local MIMAKI distributor or call a local MIMAKI office if you

need a spare waste ink tank.

•Prepare a polyethylene tank for emptying waste ink.

•If ink is dripping, wait until it stops dripping.

When the tank is filled with waste ink, the following error message is indicated:

STEP

1. Open the waste ink tank box cover.

2. Pull out the waste ink tank while pressing

it downward.

•When pulling out the waste ink tank,

hold the opening of the waste ink tank

with paper and then slowly pull it out to

prevent waste ink from spattering.

•Before replacing ink, put paper on the

floor to prevent it from being stained

with ink.

3. Dump waste ink into a separate polyethyl-

ene tank.

•Discard the waste ink according to the

local regulations of the area this unit is

used.

4. Put the empty waste ink tank back into the

device.

Close the Waste ink box cover.

•To avoid hurt hands at the corner of

the tank cover, be careful to set the

tank.

5. Press the [ENTER] key to complete the

procedure.

The device enters to the LOCAL mode.

! INK TANK

WASTE TANK FULL

WASTE TANK

TANK READY :ent

<< LOCAL >>

Indice

Altri manuali MIMAKI Stampante

MIMAKI

MIMAKI UJV-160 Manuale utente

MIMAKI

MIMAKI UJF-3042HG Istruzioni per l'installazione

MIMAKI

MIMAKI jV100-160 Manuale di manutenzione

MIMAKI

MIMAKI JV400-LX Manuale utente

MIMAKI

MIMAKI UJF-3042 MkII Manuale utente

MIMAKI

MIMAKI JV33-130 Manuale utente

MIMAKI

MIMAKI JV5-130S Manuale utente

MIMAKI

MIMAKI JV5-320DS Manuale utente

MIMAKI

MIMAKI fine Cut 3 Manuale utente

MIMAKI

MIMAKI TxF300-75 Manuale di manutenzione

MIMAKI

MIMAKI TS100-1600 Manuale di manutenzione

MIMAKI

MIMAKI UCJV300 Manuale utente

MIMAKI

MIMAKI JV150-130A Manuale di manutenzione

MIMAKI

MIMAKI Tiger600-1800TS Guida

MIMAKI

MIMAKI UJV100-160 Istruzioni per l'installazione

MIMAKI

MIMAKI JV33-260BS Manuale utente

MIMAKI

MIMAKI CJV150-75 Manuale utente

MIMAKI

MIMAKI CJV300-130 Manuale utente

MIMAKI

MIMAKI jv34 series Manuale di installazione e funzionamento

MIMAKI

MIMAKI JV300-130 BS INK Manuale utente

MIMAKI

MIMAKI UCJV300 Manuale utente

MIMAKI

MIMAKI JV5-130S Manuale utente

MIMAKI

MIMAKI UCJV300 Manuale di manutenzione

MIMAKI

MIMAKI TS34-1800A Manuale utente

Manuali Stampante popolari di altre marche

Lexmark

Lexmark 1400 Series Manuale

Canon

Canon i70 Series Manuale utente

Evolis

Evolis Elypso Manuale utente

Kyocera

Kyocera FS-9530DN Manuale utente

Canon

Canon LASER SHOT LBP-1210 Manuale utente

Samsung

Samsung BIXOLON SRP-350plusF Manuale utente

Canon

Canon PIXMA PRO-1 Series Manuale utente

Canon

Canon PIXMA G3560 Guida all'installazione

Dell

Dell Color Laser Printer 2130cn Manuale utente

Tektronix

Tektronix Phaser 840 Manuale utente

Epson

Epson ET-7750 Istruzioni operative

Canon

Canon CLBR 460ps Manuale utente

Eltron

Eltron P210 Guide Manuale utente

Ricoh

Ricoh MD-P1 Manuale utente

Epson

Epson SC-F7100 series Manuale utente

Epson

Epson Stylus C40UX Manuale utente

Canon

Canon imagePASS-A2 Manuale utente

Canon

Canon S820D Manuale utente