Minebea CSA-591 Manuale utente
Transmitter
CSA-591
Instruction Manual
EN294-1141-F
I
FOREWORD
Thank you very much for your purchasing our Transmitter CSA−591.
This manual explains installation procedures and connecting method and also operating
method for the Transmitter CSA−591. Make use of it properly after reading through the
manual carefully.
Be sure to deliver the manual to the end user. Moreover, the end user should keep the
manual at hand after reading it over.
II
Marks and arrangements used in this manual
The following marks are attached to the explanation on the matters that indicate “Don’t do
this.”, “Take care.” and “For reference”.
Be sure to read these items where these marks are attached.
Warning ●Warning may cause injury or accident that may harm to the operator.
Don’t do these things described here.
●Caution during operation and working.
Be sure to read the item to prevent malfunction.
Mark during operation.
●Press the switch.
III
For safe operation
Be sure to read this instruction manual before use.
1. Installation place
●Use the instrument where the temperature/humidity specifies with the range as follows：
Environmental temperature ：0℃to 50 ℃
Environmental humidity ：Less than 80 %R.H. (Non condensing)
(1) Location where installation is not allowed.
Warning ●Don’t locate the instrument on the places as follows :
It may cause an unexpected faulty in the instrument.
・Don’t locate the instrument in direct sunshine and/or high temperature
area.
・Don’t use the instrument in a high humid area.
・Don’t install the instrument where there are vibrations and shocks.
・Don’t use the instrument where there is excess of dusts and fine particles.
・Don’t use the instrument where there are corrosive gas and salt and like
that.
・Don’t install the instrument where there is rapid change of temperature
and humidity.
・Don’t install the instrument near the devices that are magnetized or
generate an electromagnetic field.
・Don’t install the instrument where the instrument may be affected by
radioactivity or radial rays.
・Avoid the location where chemical reaction may take place such as in a
laboratory, or like that.
IV
(2) Installation
●When installing the instrument, install as referring to the following figures and secure
the space around the instrument.
Each dimensions of the instrument and required dimensions for the environmental
spaces are as follows:
Outline dimensions
Panel cut size
Unit：mm
V
2. Power supply
Warning ●Be sure to check that the power supply is off in connecting each cable. If the work is
done while the power is on, there may have the case that electric shock to the operator
or even may have damage to the instrument.
Warning ●Before supplying the power, check that the indication of power supply voltage
/specifications for the instrument and the power going to supply should be the same.
If they are not equal, contact us.
If you use the instrument without checking them, it may cause a damage in the
instrument or electric shock to the operator.
●Earth wire should be grounded securely.
When earth wire is not connected, it may cause a malfunction of the instrument or
electric shock to the operator.
3. Application note
Warning ●Before using a new instrument or exchanging the strain gage applied transducer for a
new one, be sure to make calibration. If calibration will not be made, the correct
measuring results may not be obtained nor which may cause malfunction in the
instrument and there may exist damage in peripheral equipments.
Besides, even though calibration has been made, there may occur the similar case when
the results are not correct, so make calibration, again.
Warning ●In case of using the instrument, check that the connections are executed properly. If not
connected properly, the correct measuring result will not be obtained, nor it may cause
malfunctions of the instrument, damage to the peripheral equipments or even more
serious accidents.
Warning ●When change of setting is made carelessly on the instrument during measurement,
correct measured results may not be obtained and it may cause malfunction in the
instrument and even have the possibility of damage in peripheral instruments.
Warning ●Do not shock the instrument such as throwing something on it.
If neglected, it may cause destruction of the parts and damage to the electrical circuits.
VI
History of revision
Date Instruction manual No. Details of revised point
Feb. 2006 DRW. NO.EN294-1141 First Version
Jan.2007 DRW. NO.EN294-1141-A Due to ECN No.FN06−01050
−Correction −
former name −> “tie bar gage”
Aug. 2007 DRW. NO.EN294-1141-B
Due to ECN No.FN07−02094
−Change −
4−3. Connection Extension cable
“FA409−357“→“FA409−404”
Feb. 2010 DRW.No.EN294-1141-C Due to ECN FN10−02026
−Change −
Front cover’s logo is changed.
Oct. 2010 DRW.No.EN294-1141-D Due to ECN FN10−02140
−Change −
Minebea logo is changed.
Feb. 2018 DRW.No.EN294-1141-E Due to ECN FN17-02017
・Delete the company name in the cover page.
・Delete the company name in the contents.
Mar. 2018 DRW.No.EN294-1141-F
Due to ECN FN18-02019
－Correction－
INDEX
P10 5-2 Calibration procedure
①CSA−591 calibration by the actual load →
CSA−591 calibration procedure by the actual load
②CSA−591 (with automatically zero function) by the actual
load.→CSA−591-99 (with automatically zero function
calibration. procedure) by the actual load.
5−2−1. Calibration procedure by the actual load →
CSA-591 Calibration procedure by the actual load
P12 5-2-2 Electrical calibration by the actual load
(CSA−591−99)→CSA−591-99 (with automatically zero
function) calibration. procedure by the actual load.
P13 Procedures
－Correction drawing－
P9 5-1. The front panel was removed.
P12 The front panel was removed.
P13 Procedures
INDEX
Forwards 1........................................................
Marks and arrangementsused in this manual 2....................................
For safe operation 3............................................................
1. Installation place 3.........................................................
2. Power supply 5............................................................
3. Application note 5.........................................................
History of revision 6............................................................
1. General 1.................................................................
2. Name and function of each point 1...........................................
2−1. Front panel 1.........................................................
2−2. Rear panel 2..........................................................
3. Installation method 3.......................................................
3−1. Installation place 3....................................................
3−2. Location where installation is not allowed 3..............................
3−3. Installation 4.........................................................
4. Connecting method 5.......................................................
4−1. Layout of the terminal boards 5.........................................
4−2. Note on connection 6..................................................
4−3. Connection 7..........................................................
4−3−1. Connection of power supply and ground 8..........................
5. Calibration procedure 9....................................................
5−1. Preparation 9.........................................................
5−2. Calibration procedure 10................................................
10
5−2−1. CSA-591 Calibration procedure by the actual load ..................
12
5−2−2. CSA-591-99 Calibration procedure by the actual load. ....... .......
6. Options 14.................................................................
6−1. Automatic zero (CSA591−P99) 14........................................
6−1−1. Equivalent circuit of input/output section 14.........................
6−1−2. Function 14......................................................
7. Trouble shooting 15.........................................................
7−1. Execute trouble shooting 16.............................................
8. Specifications 18............................................................
8−1. Specifications 18.......................................................
8−2. General specifications 18................................................
8−3. Standard specification at the shipment 18.................................
8−4. Accessories 18..........................................................
8−5. Option 19..............................................................
8−6. Outline dimensions 19..................................................
9. Warranty 20................................................................
9−1. Warranty 20...........................................................
9−2. Repair 20..............................................................
Altri manuali per CSA-591
1
Indice
Altri manuali Minebea Trasmettitore
Minebea
Minebea OPT-564-71 Manuale utente
Minebea
Minebea CSA-528-80-4 Manuale utente
Minebea
Minebea CSA-591 Manuale utente
Minebea
Minebea CSA-507C Manuale utente
Minebea
Minebea CSA-593 Manuale utente
Minebea
Minebea CSA-521 Manuale utente
Minebea
Minebea OPT-564 Manuale utente
Minebea
Minebea NS100A Manuale utente
Minebea
Minebea CSA-524 Manuale utente
Minebea
Minebea CSA-562B Manuale utente
