Modern Flames CEF-50B Manuale utente

CHALLENGER WALL MOUNT/RECESSED ELECTRIC FIREPLACE

Model# : CEF-50B CEF-60B

OWNER’S MANUAL

AC 120V 60Hz 1500W (5000BTUs)

WARNING

Read and understand this entire owner’s manual, including all safety

information, before plugging in or using this product. Failure to do so could

result in fire, electric shock, or serious personal injury.

CAUTION

Keep this owner’s manual for future reference. If you sell or give this

product away, make sure this manual accompanies this product.

AFFIX SERIAL NUMBER LABEL HERE

FOR FUTURE REFERENCE

REV_03162021

IMPORTANT SAFETY INFORMATION!

WARNING

l Read all instructions before installing or using this heater.

l Use a dedicated 15 Amp (or higher) breaker.

l This heater is hot when in use. To avoid burns, DO NOT let bare skin touch hot surfaces. If

provided, use handles when moving this heater. Keep combustible materials, such as

furniture, pillows, bedding, papers, clothes, and curtains at least 3 feet (0.9m) from the front of

the heater, and keep them away from the sides and rear.

l Extreme caution is necessary when any heater is used by or near children or invalids and

whenever the heater is left operating and unattended.

l Do not operate any heater after it malfunctions. Disconnect power at service panel and have

heater inspected by a reputable electrician before reusing.

l Do not use outdoors.

l To disconnect heater, turn controls to off, and turn off power to heater circuit at main disconnect

panel (or operate internal disconnect switch if provided).

l Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may

cause an electric shock, fire, or damage the heater.

l To prevent a possible fire, do not block air intakes or exhaust in any manner.

l A heater has hot arcing or sparking parts inside. Do not use in areas where gasoline, paint,

flammable vapors, or liquids are used or stored.

l Use this heater only as described in this manual. Any other use not recommended by the

manufacturer may cause fire, electric shock, or injury to persons.

l This heater may include an audible or visual alarm to warn that parts of the heater are getting

excessively hot. If the alarm sounds (or illuminates), immediately turn the heater off and inspect

for any objects on or adjacent to the heater that may have blocked the airflow or otherwise

caused high temperatures to have occurred. DO NOT OPERATE THE HEATER WITH THE

ALARM SOUNDING (OR ILLUMINATING).

l ALWAYS plug heaters directly into a wall outlet/receptacle. NEVER use with an extension

cord or relocatable power tap (outlet/power strip).

l NEVER use this heater in bathrooms, laundry rooms, or any other location where the heater

could fall into a bathtub, pool, become damp, or come in contact with water.

l AVOID FIRE! Regularly inspect all air vents to make sure they are free from dust, lint, or other

blockage. Unplug the unit and clean with a vacuum ONLY. DO NOT rinse or get wet.

l ALWAYS mount to wall bracket before use. DO NOT set on the floor, or other surface, to use.

l NEVER use a wall mount bracket from another manufacturer.

l This product is not intended to be a primary heat source. It is for supplemental heat only.

l INDOOR use only! NEVER use this heater outdoors! Doing so may result in electric shock!

l ALWAYS disconnect this unit from the power supply before performing any assembly or

cleaning, or before relocating the electric fireplace.

l NEVER leave this heater unattended. ALWAYS unplug this heater when not in use.

l ALWAYS store this heater in a dry location. NEVER use the fireplace if it has become wet.

l NEVER plug this heater into an outlet that is old, cracked, or has any loose wires or

connections. Plugging this heater into a faulty outlet could result in electric arcing within the

outlet that could cause the outlet to overheat or catch fire.

l ALWAYS check your heater cord and plug connections with each use.

i) MAKE SURE the plug fits tight in the outlet. Faulty wall outlet connections or loose plugs can

cause the outlet to overheat.

ii) Heaters draw more current than small appliances. Overheating may occur even if it has

not occurred with the use of other appliances.

iii) During use check frequently to see if the plug outlet or face plate is HOT.

iv) If the outlet or face plate is HOT, discontinue use immediately and have a qualified

electrician inspect and/or replace the faulty outlets.

l SAVE THESE INSTRUCTIONS.

Preparation

This product includes a GLASS panel. Always use extreme caution when handling glass.

Failure to do so could result in personal injury or property damage.

Remove all parts and hardware from the carton and place them on a clean, soft, dry surface. Parts and

assembly steps are grouped for wall-hanging or recessing use. Check the parts list to make sure

nothing is missing. Dispose of packaging materials properly. Please recycle whenever possible.

You will need the following tools (not included): Phillips screwdriver, stud finder, level, tape

measure, electric drill, 1/4” wood drill bit, hammer.

Parts and Hardware

A – Fireplace

B – Wood Screws

C – Drywall anchors

D – Remote Control

E – Metal Bracket

F – Wall Bracket

Fixed on back of firebox

G – Glacier Crystals

H – Plastic Tray

I – Hardware Kit

Specification and Dimension

PRODUCT DIMENSIONS

Model

Number

CEF-50B

50-3/8"

(1280mm)

21-7/16"

(544mm)

5-3/4"

(146mm)

47-1/16"

(1195mm)

20-9/16"

(522mm)

12"

(305mm)

45-1/4"

(1149mm)

1-3/8"

(36mm)

7-1/4"

(184MM)

CEF-60B

59-7/8"

(1520mm)

21-7/16"

(544mm)

5-3/4"

(146mm)

47-1/16"

(1195mm)

20-9/16"

(522mm)

12"

(305mm)

45-1/4"

(1149mm)

1-3/8"

(36mm)

7-1/4"

(184MM)

Installation and Assembly

Your appliance is a recessed, partial recessed or wall-mount installed appliance. Select a suitable location that

is not susceptible to moisture and is away from drapes, furniture and high traffic areas.

NOTE: Follow all National and local electrical codes.

MINIMUM CLEARANCE TO COMBUSTIBLES

Measurements are taken from the glass front.

Bottom 0" Top 11-13/16" (300mm) to mantel

Sides 0" Top 11-13/16" (300mm) to ceiling

Back 0"

MINIMUM MANTEL CLEARANCES

WARNING

WHEN USING PAINT OR LACQUER TO FINISH THE MANTEL, THE PAINT OR LACQUER MUST BE

HEAT RESISTANT TO PREVENT DISCOLOURATION.

11-13/16” (300mm)

Front glass removal / installation

A. With one hand on the front glass to prevent it from falling, remove the two screws (1 per side) from

the side of the appliance (Fig. 1-1). Set the screws aside.

B. Carefully lift the front glass up and away from the appliance (Fig. 1-2 ). Place it face down on a

soft, non-abrasive surface.

C. Reverse these steps to install the front glass.

Fig. 1-1 Fig. 1-2

Recessed pre-installation

Due to the many different materials used on different walls, it is highly recommended that you

consult your local builder before you install this appliance on the wall.

A. Select a location that is not prone to moisture and is located at least 36” (94.1cm) away from

combustible materials such as curtain drapes, furniture, bedding, paper, etc.

B. Measure the appliance and create a rough-in frame with electrical (see below “framing”).

C. Remove the front glass (see “front glass removal / installation” section).

D. Hold the appliance up to ensure it will fit into the framing.

Framing Hole Size

Model Number

CEF-50B

47-1/4” (1200mm)

20-3/4” (527mm)

5-1/2” (140mm)

CEF-60B

47-1/4” (1200mm)

20-3/4” (527mm)

5-1/2” (140mm)

(Non-load bearing)

Fully recessed installation

Note: Remove power cord and complete hardwiring (see “hardwiring installation” section).

Have two people to lift the fireplace and insert to the wall opening hole.

If the appliance is fully recessed into the wall:

• Use the 6 screws (provided) to lock the appliance into the wall with the existing two side

flanges, see Figure 2-1

• Install the media and re-install the glass front.

Fig. 2-1

If partial recess into the wall:

• Use the four mounting metal brackets H (supplied) to lock the appliance to the wall, see Figure 2-3

NOTE: Using the existing holes on sides of the appliance for recessing into wall.

Fireplace will be like this after installation Figure 2-4

Fig. 2-2

Fig. 2-3

Fig. 2-4

4-5/8” (118mm)

10-7/8” (276mm)

13-3/4” (349mm)

Wall mounted installation .

Due to the many different materials used on different walls, it is highly recommended that you consult

your local builder before you install this appliance on the wall.

A. NOTE: A dedicated 15 Amp (or higher) breaker is required.

B. Select a location that is not prone to moisture and is located at least 36" (914mm) away from

combustible materials such as curtain drapes, furniture, bedding, paper, etc.

C. Have two people hold the appliance against the wall to determine the final location.

D. Place unit face down on a soft, non abrasive surface. Remove the bracket from the back of the unit by

removing the screws.

E. Mark location, then mount the bracket(s) onto

the wall using the supplied screws.

This bracket MUST have the hooks facing

upward and be level. NOTE: It is strongly

recommended that the mounting bracket

(F) be Screwed into the wall studs where

possible. If the wall studs cannot be used, ensure the supplied plastic anchors are used to affix

the bracket to the wall and the bracket is adequately secured.

F. With the wall mounting bracket installed have two people lift the appliance up and insert the two hooks

on the bracket into the two slots on the back of the appliance.

G. Check the appliance for stability ensuring that the bracket will not pull free from the wall.

H. Install the side skirt panels to each side of firebox.

Wall Bracket Illustrated

Hard wiring installation .

HARD WIRING CONNECTION

If it is necessary to hard wire this appliance, a qualified electrician must remove the cord

connection, and wire the appliance directly to the household wiring. NOTE: A dedicated 15 Amp

(or higher) breaker is required.

This appliance must be electrically connected and grounded in accordance with local codes if hard wired.

TURN OFF POWER FROM CIRCUIT BREAKER FIRST

A. Remove the cover plate from the right side bottom of the appliance by removing the three screws,

as shown above.

B. Remove the wire connectors from the power cord. The power cord may be discarded.

C. Take the new cover plate, supplied in the hardware bag and punch out the 7/8" (22.2mm) hole and install

a box connector through, into the junction box. Snap the box connector clamp onto the supply wires.

D. Using the wire connectors, connect the ground green wires (G), the common white wires (N)

together, then the hot black wires (L),

E. Re-install the cover plate using the three screws.

WARNING

TURN OFF THE APPLIANCE COMPLETELY AND LET COOL BEFORE SERVICING. ONLY A QUALIFIED SERVICE

PERSON SHOULD SERVICE AND REPAIR THIS ELECTRIC APPLIANCE.

Box connector

Cover plate (I)

Cable connector

(I)

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Modern Flames Camino da interno

Modern Flames

Modern Flames FusionFire 60 Manuale di istruzioni

Modern Flames

Modern Flames WMC LPM Series Manuale utente

Modern Flames

Modern Flames Landscape Pro Multi Series Istruzioni operative

Modern Flames

Modern Flames LPM-9616/INT Istruzioni operative

Modern Flames

Modern Flames NOVA 60 Istruzioni originali

Modern Flames

Modern Flames LPM-4416V2 Manuale utente

Modern Flames

Modern Flames AL45CLX Istruzioni di installazione e manutenzione

Modern Flames

Modern Flames SPM-2426V2 Manuale utente

Modern Flames

Modern Flames SPS-50B-AU Manuale utente

Modern Flames

Modern Flames Landscape Pro Multiview Series Istruzioni per l'installazione

Modern Flames

Modern Flames Landscape Pro Multi Guida rapida

Modern Flames

Modern Flames Sedona Pro multi Series Istruzioni operative

Modern Flames

Modern Flames AL 95 Manuale utente

Modern Flames

Modern Flames Sunset Charred Oak Istruzioni operative

Modern Flames

Modern Flames SPECTRUM SLIMLINE SPS-50B-EU Manuale utente

Modern Flames

Modern Flames Landscape Pro Multiview Series Manuale utente

Modern Flames

Modern Flames INSERT FIRE 3824 Istruzioni originali

Modern Flames

Modern Flames Landscape Pro Slim Series Istruzioni operative

Modern Flames

Modern Flames AMBIANCE LINEAR 40 Istruzioni originali

Modern Flames

Modern Flames Landscape Pro Slim LPS-4414V2 Manuale utente

Modern Flames

Modern Flames LFV2-40/15-SH Istruzioni di installazione e manutenzione

Modern Flames

Modern Flames ORION OR26-TRAD Manuale utente

Modern Flames

Modern Flames RS-2621-EU Manuale utente

Modern Flames

Modern Flames OR52-SLIM Manuale utente

Manuali Camino da interno popolari di altre marche

Brigantia

Brigantia 35-DVRS31N-2 Manuale del proprietario

Nordpeis

Nordpeis Bergen Manuale utente

Superior

Superior BCT2536TMN Manuale utente

Quadra-Fire

Quadra-Fire 5100I-GD-B Manuale utente

Renaissance

Renaissance RUMFORD 1000 Manuale utente

Lacunza

Lacunza IV-800 Manuale utente

Baxi

Baxi 940 Istruzioni per l’uso

Dru

Dru Maestro 60/2 Tall RCH Manuale utente

Diamond Fireglass

Diamond Fireglass SS-O22 Manuale utente

HearthStone

HearthStone Windsor Bay 8830 Manuale di programmazione

Napoleon

Napoleon ASCENT B42 Manuale utente

Enviro

Enviro E33GI Manuale utente

Smeg

Smeg L30 FABE Istruzioni di montaggio

KEDDY

KEDDY K700 Manuale utente

Godin

Godin 3451 Manuale utente

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Manuale utente

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 Manuale utente

Desa

Desa CCFPDFT Manuale operativo