molex 207129 Series Manuale utente
Tool Kit for 250 MP-Lock Terminal
Doc No: ATS-6381 64HM Release Date: 0 -20-10 UNCONTROLLED COPY Page 1 of 8
Revision: B Revision Date: 0 -20-10
INSULATION
CRIMP
BRUSH
STRIP
LENGTH
CONDUCTOR
CRIMP HEIGHT
CUT-OFF
TAB
SEAM
BELL MOUTH
WIRE
Application Tooling
Sp cification Sh t
Tool Kit
Ord r No. 63819-6470
Hand Crimp Tool
Ord r No. 63819-6400
FEATURES
% A full cycle ratcheting hand tool ensures complete crimps
% Ergonomically designed soft handles
% Precisely designed crimping profiles with simple contact positioning
% Easy handling due to outstanding force ratio
Tool kits are easily installed into the Hand Crimp Tool or the 63816-0300 Power Crimp Head which is installed
into the 63816-0200 (110 V) or the 63816-0250 (220 V) Battery Powered Tool.
Many different Tool kits can be used with a single Battery Powered Tool.
This tool is IPC/WHMA-A-620 Class 2 and RoHS compliant.
SCOPE
Products: .250 MP-Lock Terminals for 14 – 18 AWG Wire.
T rminal S ri s No.
T rminal Ord r No.
Wir Siz Insulation Diam t r Strip L ngth
R l Form Only
AWG
mm²
mm In. mm In.
35072 35072- 802
14 2.21
2.2 – 3.4
.086 - .133
5.0 - 5.6
.1 7 - .220
16 1.31
18 0.81
Customer to cut off terminal from reel: 0.50mm (.020”) maximum Cut-off Tab.
DEFINITION OF TERMS
The above terminal drawing is a generic terminal representation. It is not an image of a terminal listed in the
scope.
TYPE 4C
Tool Kit for 250 MP-Lock Terminal
Doc No: ATS-6381 64HM Release Date: 0 -20-10 UNCONTROLLED COPY Page 2 of 8
Revision: B Revision Date: 0 -20-10
ANVILS
POWER
CRIMP
HEAD
Figur 1
PUNCHES
M4 X 10 LONG
BHCS
M4 X 18 LONG
BHCS
SWING
LOCATOR
OPEN
PRESS DOWN
ON THE BRASS
PIVOT SHAFT
LIFT UP ON
THE LOCATOR
Figur 2
CONDITIONS:
After crimping, the conductor profiles should measure the following (See notes below).
T rminal
S ri s No.
Wir Siz Conductor Crimp Insulation Crimp Pull Forc
Minimum Profil
H ight Punch Width (R f) H ight Punch Width (R f)
AWG
mm2
mm In. mm In. mm
In. mm In. N Lbs
A
B
C
35072
14 2.21
1.7 -1.8
.070-.074
2.80-2.82
.110-.111
4.00
.157
4.00-4.02
.157-.158
225.4
50.7
X
16 1.31
1.63-1.73
.064-.068
2.80-2.82
.110-.111
3.80
.150
4.00-4.02
.157-.158
1 6.0
44.1
X
18 0.81
1.47-1.57
.058-.062
2.80-2.82
.110-.111
3.60
.142
4.00-4.02
.157-.158
117.6
26.4
X
Tool Qualification Notes:
1. Pull Force should be measured with no influence from the insulation crimp.
2. The above specifications are guidelines to an optimum crimp.
Not :
A crimp height chart is provided with this manual as Reference Only. Due to the wide range of wires, strands,
insulation diameters, and durometers, actual crimp height measurements may very slightly. An occasional,
destructive, pull force test should be preformed to check hand tool crimp. Pull Force value must exceed the
minimum pull force specifications listed.
CAUTION: Install only Molex terminals listed above with this tool. Do not crimp hardened objects as damage
can occur to the tool or die.
INSTALLATION
To install the Tool Kit into the Power Crimp Head follow the steps below:
Anvils and Punch s Installation
1. Insert the Anvils into the bottom slots of the nest. Install the M4 x 10 long BHCS and tighten in place.
2. Insert the Punches into the top slots of the nest. Install the M4 x 18 long BHCS and tighten in place. See
Figure 1.
Tool Kit for 250 MP-Lock Terminal
Doc No: ATS-6381 64HM Release Date: 0 -20-10 UNCONTROLLED COPY Page 3 of 8
Revision: B Revision Date: 0 -20-10
SWING OPEN
TERMINAL
PUSH HERE TO
OPEN WIRE STOP LOCATOR TERMINAL
IN PLACE
Figur 4
LOCATOR LATCH
IN OPEN POSITION
Locator Installation and R moval
Follow the steps below to install or replace the locator. See Figure 2.
To install th locator
1. Position the locator with the hole over the brass pivot shaft and snap it into place.
To r mov th locator
1. Open the crimp hand tool.
2. Swing the existing locator open and away from the hand tool.
3. Firmly press down on the brass pivot shaft with your thumb, while pulling the locator up. Slip the locator off the
top of the brass pivot shaft.
OPERATION
Open the tool by squeezing the handles together, at the
end of the closing stroke, the ratchet mechanism will
release the handles, and the hand tool will spring open.
Crimping T rminals
1. Select the desired terminal listed in the preceding
charts.
2. Turn the Locator Lock Latch down to unlock. See
Figure 3.
3. Swing the terminal locator away from the crimp tool
shown in Figure 4. Some terminals with large insulation grips may interfere with the crimp tooling when
swinging the locator into position. The terminal must then be loaded into the locator in the closed/crimp
position. See Figure 5.
4. Press down on the wire stop on the locator as shown in Figure1. Insert the proper terminal into the proper nest
opening. Make sure when choosing the nest opening, it will correspond with the A, B or C profile on the hand
tool.
5. Return the locator to its
original position.
6. Turn the Locator Lock
Latch up to lock. Make
sure that the terminal is
visually centered over the
punch.
7. Insert the proper wire over
the terminal.
8. Gently touch the wire stop
with the end of the wire.
See Figure 6 and 7.
Figur 3
LATCH LOCKED
LATCH UNLOCKED
Tool Kit for 250 MP-Lock Terminal
Doc No: ATS-6381 64HM Release Date: 0 -20-10 UNCONTROLLED COPY Page 4 of 8
Revision: B Revision Date: 0 -20-10
Figur 6
WIRE IN TERMINAL
JAWS
PARTIALLY
CLOSED
WIRE AGAINST
WIRE STOP
HANDLE
OPEN
LOCATOR
CLOSED
Figur 5
TERMINAL
PUSH HERE TO
OPEN WIRE STOP
. Compress the terminal by squeezing the tool handles until the ratchet mechanism cycle has been completed.
Release handles to open the jaws.
10. Remove the crimped terminal from the terminal locator by pressing down on the wire stop and gently pulling on
the wire. The terminal locator can be in either position.
11. Visually inspect the crimped terminal for proper crimp location.
Not : The tamper proof ratchet action will not release the tool until it has been fully closed.
For th Batt ry Pow r Tool:
1. Cycle the Battery Power Tool to crimp the
terminal to the wire.
2. Remove the crimped terminal from the terminal
locator by pressing down on the wire stop and
gently pulling on the wire. The terminal locator
can be in either position.
3. Visually inspect the crimped terminal for proper
crimp location.
Maint nanc
It is recommended that each operator of the tool be
made aware of, and responsible for, the following
maintenance steps:
1. Remove dust, moisture and other contaminants
with a clean brush, or soft, lint-free cloth.
2. Do not use any abrasive materials that could damage the tool.
3. Make certain all pins; pivot points and bearing surfaces in the tool head are protected with a thin coat of high
quality machine oil. Do not oil excessively. This tool was engineered for durability, but like any fine piece of
equipment, it needs cleaning and lubrication for a maximum service life of trouble-free crimping. The use of
light oil, such as 30 weight automotive oil, every 5,000 crimps or monthly, will significantly enhance the tool life
and ensure a stable calibration. See Figure 8A or 8B for lubrication points.
4. Store the tool in a clean and dry area when not in use.
Figur 7
WIRE
INSULATION
PUNCH
CONDUCTOR ANVIL
LOCATOR
INSULATION
ANVIL
WIRES AGAINST
LOCATOR STOP
CONDUCTOR
PUNCH
TERMINAL
Tool Kit for 250 MP-Lock Terminal
Doc No: ATS-6381 64HM Release Date: 0 -20-10 UNCONTROLLED COPY Page 5 of 8
Revision: B Revision Date: 0 -20-10
Miscrimps or Jams for Crimp Hand Tools Only
(S Figur 11)
Should this tool ever become stuck or jammed
in a partially closed position, Do Not force the
handles open or closed. The tool will open
easily by rotating the small slotted screw
marked with an arrow. See Figure 11.
Warranty
This tool kit is for electrical terminal crimping
purposes only. This tool kit is made of the best
quality materials. All vital components are long
life tested. All tools are warranted to be free of
manufacturing defects for a period of 30 days.
Should such a defect occur, we will repair or
exchange the tool kit free of charge. This repair or exchange will not be applicable to altered, misused, or
damaged tools.
CAUTION: Molex crimp specifications are valid only when used with Molex terminals and tooling.
CAUTIONS
1. Manually powered hand tools are intended for low volume or field repair. This tool is NOT intended for
production use. Repetitive use of this tool should be avoided.
2. Insulated rubber handles are not protection against electrical shock.
3. Wear eye protection at all times.
4. Use only the Molex terminals specified for crimping with this tool.
CAUTION: Repetitive use of this tool should be avoided.
C rtification
Molex does not certify or re-certify commercial grade hand tools but rather supplies the following guidelines for
customers to re-certify hand tools.
% This tool is qualified to pull force only. To re-certify, crimp a terminal to a wire, which has been stripped
12.7mm (1/2”) long, so there is no crimping of the insulation. Pull the terminal and wire at a rate no faster than
25mm (1.00”) per minute. See the Molex web site for the Quality Crimp Handbook for more information on pull
testing.
% When the hand tool is no longer capable of achieving minimum pull force, it should be taken out of service and
replaced.
% This tool is very difficult to disassemble and reassemble. Customer repair is not recommended.
LUBRICATION
POINTS
(BOTH SIDES)
LIGHT OIL
(EVERY MONTH
OR
5,000 CRIMPS)
Figur 7A
Figur 7B
Tool Kit for 250 MP-Lock Terminal
Doc No: ATS-6381 64HM Release Date: 0 -20-10 UNCONTROLLED COPY Page 6 of 8
Revision: B Revision Date: 0 -20-10
The chart below shows all applications for this Tool Kit.
Tool Kit
Ord r No.
Tool
Ord r no.
Tool
D scription
Pow r H ad
Ord r No.
Adapt r
D scription
Figur
No.
6381 -6470
63810-1050
Hand Crimp Frame (Short) N/A N/A
63810-1000
Hand Crimp Frame (Long) N/A N/A
63816-0200
Battery Power Tool (110 V)
63816-0300 Power Crimp Head
10
63816-0250
Battery Power Tool (220 V)
63816-0300 Power Crimp Head
10
Applications for th Tool Kit
Hand Crimp Tool Batt ry Pow r d Tool
Figur 9 Figur 10
WARNING: NEVER operate service, install tool kits, or adjust the Power Crimp Head without proper
instruction and without first reading and understanding the instructions in the proper Manual or
Specification Sheet. See Chart above for the correct Manual or Specification Sheet.
WARNING: NEVER install tooling or service this tool while it is into any power source. Make sure the
power is turned off.
CAUTION: Keep fingers away from the crimping area when operating this tool. It may cause severe injury.
CAUTION: Wear safety glasses when operating or serving this tool.
P
OWER
CRIMP
HEAD
LOCKING PINS
BATTERY
POWERED
TOOL
TOOLING KIT
HAND CRIMP
FRAME LONG
AND SHORT
TOOLING KIT
Tool Kit for 250 MP-Lock Terminal
Doc No: ATS-6381 64HM Release Date: 0 -20-10 UNCONTROLLED COPY Page 7 of 8
Revision: B Revision Date: 0 -20-10
RATCHET
RELEASE SCREW
Figur 11
M4 X 8mm
LONG BHCS
2
1
3
M4 X 18mm
LONG BHCS
M4 X 10mm
LONG BHCS
2
4
WITH TOOL KIT
LOCATOR ONLY
HAND TOOL PARTS LIST
It m Numb r Ord r Numb r D scription Quantity
1 63810-1000 Hand Crimp Frame (Long) 1
2 6381 -6470 Tool Kit with Locator 1
3 63811-4773 Locator Base 1
4 6381 -6475 Locator (only) REF
Tool Kit for 250 MP-Lock Terminal
Doc No: ATS-6381 64HM Release Date: 0 -20-10 UNCONTROLLED COPY Page 8 of 8
Revision: B Revision Date: 0 -20-10
Figur 12
1
2
2
M4 by 8 Long
BHCS
M4 by 18 Long
BHCS
M4 by 10 Long
BHCS
1
POWER HEAD PARTS LIST
It m Ord r No Engin ring No. D scription Quantity
1
63816-0300 63816-0300 Power Crimp Head 1
2
6381 -6470 6381 -6470 Tool Kit 1
http://www.molex.com
Altri manuali per 207129 Series
100
Questo manuale è adatto per i seguenti modelli
2
Indice
Altri manuali molex Utensili per crimpatura
molex
molex 207129 Series Manuale utente
molex
molex 64001-1000 Manuale utente
molex
molex 64001-2800 Manuale utente
molex
molex 63811-4700 Manuale utente
molex
molex 63819-0900 Manuale utente
molex
molex 105300 Series Manuale utente
molex
molex 200218-4500 Guida utente
molex
molex 63811-5300 Manuale utente
molex
molex 207129 Series Manuale utente
molex
molex 63825-5500 Guida utente
molex
molex 64001-5900 Manuale utente
molex
molex 63828-1900 Manuale utente
molex
molex 207129 Series Manuale utente
molex
molex 63823-4100 Manuale utente
molex
molex AT 1610 Manuale utente
molex
molex 207129 Series Manuale per l'uso e la cura
molex
molex 207129 Series Manuale utente
molex
molex 63825-5770 Manuale utente
molex
molex 207129 Series Manuale utente
molex
molex 64001-8800 Manuale utente
Manuali Utensili per crimpatura popolari di altre marche
Textron
Textron ESG105L Manuale utente
Tyco Electronics
Tyco Electronics 90035-3 Manuale utente
Emerson
Emerson Klauke ES 20RMCCFB Manuale utente
Continental Refrigerator
Continental Refrigerator PC150HD Manuale utente
TE Connectivity
TE Connectivity ERGOCRIMP 1-1579001-3 Manuale utente
Tyco Electronics
Tyco Electronics CERTI-CRIMP 90418-1 Manuale utente