molex 207129 Series Manuale utente
Tool Kit for 5.77mm (.227") Crimp Terminal, Pin
Doc No: ATS- 381158HM Release Date: 02-20-07 UNCONTROLLED COPY Page 1 of 8
Revision: G Revision Date: 05-24-11
Application Tooling
Specification Sheet
Tool Kit
Order No. 6 811-5870
Hand Crimp Tool
Order No. 6 811-5800
FEATURES
% A full cycle ratcheting hand tool ensures complete crimps
% Ergonomically designed soft handles
% Precisely designed crimping profiles with simple contact positioning
% Easy handling due to outstanding force ratio
Tool kits are easily installed into the Hand Crimp Tool or the 381 -0300 Power Crimp Head which is installed
into the 381 -0200 (110 V) or the 381 -0250 (220 V) Battery Powered Tool.
Many different Tool kits can be used with a single Battery Powered Tool.
This tool is IPC/WHMA-A- 20 Class 2 and RoHS compliant.
SCOPE
Products: 5.77mm (.227") Crimp Terminal, Pin, 14-18 AWG.
Terminal Series No. Terminal Order No. Wire Size Insulation Diameter Strip Length
Available in Reel form only AWG mm² mm in mm in
84524 84524-0012 84524-0018
14 2.09 3.30-3.81 .130-.150
1 1.33 2.92-3.30 .115-.130 4.45 .175
18 0.82 2.41-2.92 .095-.115
84525 84525-0025 84525-004
14 2.09 3.30-3.81 .130-.150
1 1.33 2.92-3.30 .115-.130 4.45 .175
18 0.82 2.41-2.92 .095-.115
84590
84590-0021
84590-0024
84590-0027
84590-0030
84590-003
84590-0039
14 2.09 3.30-3.81 .130-.150
4.45 .175 1 1.33 2.92-3.30 .115-.130
18 0.82 2.41-2.92 .095-.115
Customer to cut off terminal from reel: 0.50mm (.020”) maximum Cut-off Tab.
TYPE 4C
Tool Kit for 5.77mm (.227") Crimp Terminal, Pin
Doc No: ATS- 381158HM Release Date: 02-20-07 UNCONTROLLED COPY Page 2 of 8
Revision: G Revision Date: 05-24-11
CONDUCTOR
BRUSH
STRIP LENGTH
SEAM
BEND UP
TWISTING
ROLLING
BEND
DOWN
CONDUCTOR
CRIMP
CUT-OFF
TAB
BELL MOUTH
WIRE
DEFINITION OF TERMS
CRIMP SPECIFICATION
Terminal Series No. Bell Mouth Bend up Bend down Twist Roll Conductor Brush
mm In. Degree Degree mm In.
84524 84525 84590 0.13-0.37 .005-.015 5 5 5 10 0.75-1.25 .030-.050
Seam
Seam shall not be open and no wire allowed out of the crimping area
CONDITIONS:
After crimping, the conductor profiles should measure the following (See notes below).
Terminal Series No. Wire Size Conductor Pull Force
Minimum Profile
Crimp Height (Ref) Crimp Width (Ref)
AWG
mm2 mm in. mm in. N Lb. 14 16 18
84524
14 2.09 1.73-1.81 .0 8-.071 2.55 .100 111.2 25.0 X
1 1.33 1.48-1.5 .058-.0 1 2.55 .100 111.2 25.0 X
18 0.82 1.3 -1.44 .054-.057 2.55 .100 111.2 25.0 X
84525
14 2.09 1.73-1.81 .0 8-.071 2.55 .100 111.2 25.0 X
1 1.33 1.48-1.5 .058-.0 1 2.55 .100 111.2 25.0 X
18 0.82 1.3 -1.44 .054-.057 2.55 .100 111.2 25.0 X
84590
14 2.09 1.73-1.81 .0 8-.071 2.55 .100 111.2 25.0 X
1 1.33 1.48-1.5 .058-.0 1 2.55 .100 111.2 25.0 X
18 0.82 1.3 -1.44 .054-.057 2.55 .100 111.2 25.0 X
Tool Qualification Notes:
1. Pull Force should be measured with no influence from the insulation crimp.
2. The above specifications are guidelines to an optimum crimp.
Note:
A crimp height chart is provided with this manual as Reference Only. Due to the wide range of wires, strands,
insulation diameters, and durometers, actual crimp height measurements may very slightly. An occasional,
destructive, pull force test should be preformed to check hand tool crimp. Pull Force value must exceed the
minimum pull force specifications listed.
Tool Kit for 5.77mm (.227") Crimp Terminal, Pin
Doc No: ATS- 381158HM Release Date: 02-20-07 UNCONTROLLED COPY Page 3 of 8
Revision: G Revision Date: 05-24-11
ANVILS
POWER
CRIMP
HEAD
Figure 1
PUNCHES
M4 X 10 LONG
BHCS
M4 X 18 LONG
BHCS
SWING
LOCATOR
OPEN
PRESS DOWN
ON THE BRASS
PIVOT SHAFT
LIFT UP ON
THE LOCATOR
Figure 2
CAUTION: Install only Molex terminals listed above with this tool. Do not crimp hardened objects as damage
can occur to the tool or die.
INSTALLATION
To install the Tool Kit into the Power Crimp Head follow the steps below:
Anvils and Punches Installation
1. Insert the Anvils into the bottom slots of the nest. Install the M4 x 10 long BHCS and tighten in place.
2. Insert the Punches into the top slots of the nest. Install the M4 x 18 long BHCS and tighten in place. See
Figure 1.
Locator Installation and Removal
Follow the steps below to
install or replace the locator.
See Figure 2.
To install the locator
1. Position the locator with
the hole over the brass
pivot shaft and snap it into
place.
To remove the locator
1. Open the crimp hand tool.
2. Swing the existing locator
open and away from the
hand tool.
3. Firmly press down on the brass pivot shaft with your thumb, while pulling the locator up. Slip the locator off the
top of the brass pivot shaft.
SWING OPEN
TERMINAL
PUSH HERE TO
OPEN WIRE STOP
LOCATOR
LOCATOR TERMINAL IN PLACE
Figure
Tool Kit for 5.77mm (.227") Crimp Terminal, Pin
Doc No: ATS- 381158HM Release Date: 02-20-07 UNCONTROLLED COPY Page 4 of 8
Revision: G Revision Date: 05-24-11
HANDLE
OPEN
LOCATOR
CLOSED
Figure 4
TERMINAL
PUSH HERE TO
OPEN WIRE STOP
Figure 5
WIRE IN TERMINAL
JAWS
PARTIALLY
CLOSED
WIRE AGAINST
WIRE STOP
OPERATION
Open the tool by squeezing the handles together, at the end of the closing stroke, the ratchet mechanism will
release the handles, and the hand tool will spring open.
Crimping Terminals
1. Select the desired terminal listed in the preceding charts.
2. Swing the terminal locator away from the crimp tool shown in Figure 3. Some terminals with large insulation
grips may interfere with the crimp tooling when swinging the locator into position. The terminal must then be
loaded into the locator in the closed crimp position. See Figure 4.
3. Press down on the wire stop on the locator as shown in Figure 4. Insert the proper t5rminal into the proper
nest opening. Make sure when choosing the nest opening, it will correspond with the 14, 1 , or 18 profile on
the hand tool. See Figure 5.
4. Return the locator to its original position.
5. Insert the proper wire over the terminal. Gently touch the wire stop with the end of the wire.
See Figure 5 and .
. Compress the terminal by squeezing the tool handles until the ratchet mechanism cycle has been completed.
Release handles to open the jaws.
Note: The tamper proof ratchet action will not release the tool until it has been fully closed.
7. Remove the crimped terminal from the terminal
locator by pressing down on the wire stop and gently
pulling on the wire. The terminal locator can be in
either position.
8. Visually inspect the crimped terminal for proper crimp
location.
For the Battery Power Tool:
1. Cycle the Battery Power Tool to crimp the terminal to
the wire.
2. Remove the crimped terminal from the terminal
locator by pressing down on the wire stop and gently
pulling on the wire. The terminal locator can be in
either position.
Figure 6
WIRE
INSULATION
PUNCH
CONDUCTOR ANVIL
LOCATOR
INSULATION
ANVIL
WIRES AGAINST
LOCATOR STOP
CONDUCTOR
PUNCH
TERMINAL
Tool Kit for 5.77mm (.227") Crimp Terminal, Pin
Doc No: ATS- 381158HM Release Date: 02-20-07 UNCONTROLLED COPY Page 5 of 8
Revision: G Revision Date: 05-24-11
3. Visually inspect the crimped terminal for
proper crimp location.
Maintenance
It is recommended that each operator of the
tool be made aware of, and responsible for,
the following maintenance steps:
1. Remove dust, moisture and other
contaminants with a clean brush, or soft,
lint-free cloth.
2. Do not use any abrasive materials that
could damage the tool.
3. Make certain all pins; pivot points and bearing surfaces in the tool head are protected with a thin coat of high
quality machine oil. Do not oil excessively. This tool was engineered for durability, but like any fine piece of
equipment, it needs cleaning and lubrication for a maximum service life of trouble-free crimping. The use of a
light oil, such as 30 weight automotive oil, every 5,000 crimps or monthly, will significantly enhance the tool life
and ensure a stable calibration. See Figure 7A or 7B for lubrication points.
4. Store the tool in a clean and dry area when not in use.
Miscrimps or Jams for Crimp Hand Tools Only (See Figure 10)
Should this tool ever become stuck or jammed in a partially closed position, Do Not force the handles open or
closed. The tool will open easily by rotating the small slotted screw marked with an arrow. See Figure 10.
Warranty
This tool kit is for electrical terminal crimping purposes only. This tool kit is made of the best quality materials. All
vital components are long life tested. All tools are warranted to be free of manufacturing defects for a period of 30
days. Should such a defect occur, we will repair or exchange the tool kit free of charge. This repair or exchange
will not be applicable to altered, misused, or damaged tools.
CAUTION: Molex crimp specifications are valid only when used with Molex terminals and tooling.
CAUTIONS
1. Manually powered hand tools are intended for low volume or field repair. This tool is NOT intended for
production use. Repetitive use of this tool should be avoided.
2. Insulated rubber handles are not protection against electrical shock.
3. Wear eye protection at all times.
4. Use only the Molex terminals specified for crimping with this tool.
CAUTION: Repetitive use of this tool should be avoided.
Certification
Molex does not certify or re-certify commercial grade hand tools but rather supplies the following guidelines for
customers to re-certify hand tools.
LUBRICATION
POINTS
(BOTH SIDES)
LIGHT OIL
(EVERY MONTH
OR
5,000 CRIMPS)
Figure 7A
Figure 7B
Tool Kit for 5.77mm (.227") Crimp Terminal, Pin
Doc No: ATS- 381158HM Release Date: 02-20-07 UNCONTROLLED COPY Page of 8
Revision: G Revision Date: 05-24-11
% This tool is qualified to pull force only. To re-certify, crimp a terminal to a wire, which has been stripped
12.7mm (1/2”) long, so there is no crimping of the insulation. Pull the terminal and wire at a rate no faster than
25mm (1.00”) per minute. See the Molex web site for the Quality Crimp Handbook for more information on pull
testing.
% When the hand tool is no longer capable of achieving minimum pull force, it should be taken out of service and
replaced.
% This tool is very difficult to disassemble and reassemble. Customer repair is not recommended.
The chart below shows all applications for this Tool Kit.
Tool Kit
Order No.
Tool
Order no.
Tool
Description
Power Head
Order No.
Adapter
Description
Figure
No.
3811-5870
3810-1050
Hand Crimp Frame (Short) N/A N/A 8
3810-1000
Hand Crimp Frame (Long) N/A N/A 8
381 -0200
Battery Power Tool (110 V)
381 -0300 Power Crimp Head
9
381 -0250
Battery Power Tool (220 V)
381 -0300 Power Crimp Head
9
Applications for the Tool Kit
Hand Crimp Tool Battery Powered Tool
Figure 8 Figure 9
WARNING: NEVER operate service, install tool kits, or adjust the Power Crimp Head without proper
instruction and without first reading and understanding the instructions in the proper Manual or
Specification Sheet. See Chart above for the correct Manual or Specification Sheet.
WARNING: NEVER install tooling or service this tool while it is into any power source. Make sure the
power is turned off.
CAUTION: Keep fingers away from the crimping area when operating this tool. It may cause severe injury.
CAUTION: Wear safety glasses when operating or serving this tool.
POWER
CRIMP
HEAD
LOCKING PINS
BATTERY
POWERED
TOOL
TOOLING KIT
HAND CRIMP
FRAME LONG
AND SHORT
TOOLING KIT
Tool Kit for 5.77mm (.227") Crimp Terminal, Pin
Doc No: ATS- 381158HM Release Date: 02-20-07 UNCONTROLLED COPY Page 7 of 8
Revision: G Revision Date: 05-24-11
RATCHET
RELEASE SCREW
Figure 10
M4 X 8mm
LONG BHCS
2
1
M4 X 18mm
LONG BHCS
M4 X 10mm
LONG BHCS
2
4
WITH TOOL KIT
LOCATOR ONLY
HAND TOOL PARTS LIST
Item Number Order Number Description Quantity
1 3810-1000 Hand Crimp Frame (Long) 1
2 3811-5870 Tool Kit with Locator 1
3 3811-5573 Locator Base 1
4 3811-5 75 Locator (only) REF
Tool Kit for 5.77mm (.227") Crimp Terminal, Pin
Doc No: ATS- 381158HM Release Date: 02-20-07 UNCONTROLLED COPY Page 8 of 8
Revision: G Revision Date: 05-24-11
Figure 11
1
2
2
M4 by 8 Long
BHCS
M4 by 18 Long
BHCS
M4 by 10 Long
BHCS
1
POWER HEAD PARTS LIST
Item Order No Engineering No. Description Quantity
1
381 -0300 381 -0300 Power Crimp Head 1
2
3811-5870 3811-5870 Tool Kit 1
http://www.molex.com
Altri manuali per 207129 Series
100
Questo manuale è adatto per i seguenti modelli
2
Indice
Altri manuali molex Utensili per crimpatura
molex
molex 63819-7670 Manuale utente
molex
molex 63819-0500 Guida utente
molex
molex 207129 Series Manuale utente
molex
molex 63819-0900 Manuale utente
molex
molex 207129 Series Manuale utente
molex
molex 63811-4400 Manuale utente
molex
molex 207129 Series Manuale utente
molex
molex PremiumGrade Series Manuale utente
molex
molex 63819-4100 Manuale utente
molex
molex 64001-2800 Manuale utente
molex
molex 63811-8300 Manuale utente
molex
molex 63819-1300 Manuale utente
molex
molex 63827-6270 Manuale utente
molex
molex 63811-9370 Manuale utente
molex
molex 63823-4500 Guida utente
molex
molex 63816-0200 Manuale utente
molex
molex 4D Manuale utente
molex
molex 207129 Series Manuale utente
molex
molex 64005-3400 Manuale utente
molex
molex 207129 Series Manuale utente
Manuali Utensili per crimpatura popolari di altre marche
Textron
Textron ESG105L Manuale utente
Tyco Electronics
Tyco Electronics 90035-3 Manuale utente
Emerson
Emerson Klauke ES 20RMCCFB Manuale utente
Continental Refrigerator
Continental Refrigerator PC150HD Manuale utente
TE Connectivity
TE Connectivity ERGOCRIMP 1-1579001-3 Manuale utente
Tyco Electronics
Tyco Electronics CERTI-CRIMP 90418-1 Manuale utente