molex 207129 Series Manuale utente
Air Crimp Tool Head
Doc No: ATS-640073500 Release Date: 06-08-04 UNCONTROLLED COPY Pa e 1 of 6
Revision: B Revision Date: 07-05-06
Air Powered
Crimp Tool Head
Application Tooling
Specification Sheet Order No 64007-3500
FEATURES
Quick-chan e tool head for the 19279-0001 (AT-200)
3-nested tool eliminates the need for additional tools
A precision user-friendly terminal locator wire stop holds terminals in the proper crimpin position for each of
the three nests
Pneumatic powered crimp tools help reduce fati ue and discomfort from repetitive manual crimpin
SCOPE
Products: 2.13mm (.084”) Diameter Solid Pin and Socket Male Terminals and Female Connector Terminals for 14–
20 AWG. This tool head is intended for use in the 19279-0001 (AT-200) either hand held or with optional
bench adapter 19078-0307 (ATBA) and foot switch.
Terminal Series No
Wire Size
Insulation Diameter
Strip Length
AWG
mm²
mm
In
mm
In
42023
14
-
20
2.00
-
0.50
1.52
-
3.30
.060
-
.130
3.96
-
5.53
.156
-
.218
42024
14
-
20
2.00
-
0.50
1.
52
-
3.30
.060
-
.130
3.96
-
5.53
.156
-
.218
Conditions
After crimpin , the conductor profile should measure the followin . See notes on pa e 2.
Note:
It may be required to run 18 AWG terminals with pressure settin at 120 PSI on the re ulator.
Terminal Series No Wire Size
Crimp Height
(REF)
Punch Width
(Ref) Pull Force Minimum Profile
AWG
mm
2
mm
In
mm
In
N
Lb
A
B
C
42023
14
2.00
1.55
-
165
.061
-
.065
2.70
3.20
222.4
50.00
X
16
1.30
1.40
-
1.50
.055
-
.059
2.50
3.20
133.4
30.00
X
18
0.80
1.30
-
1.40
.
051
-
.055
2.20
2.80
88.9
20.00
X
20
0.50
1.30
-
1.40
.051
-
.055
2.20
2.80
57.8
13.00
X
42024
14
2.00
1.55
-
165
.061
-
.065
2.70
3.20
222.4
50.00
X
16
1.30
1.40
-
1.50
.055
-
.059
2.50
3.20
133.4
30.00
X
18
0.80
1.30
-
1.40
.051
-
.055
2.20
2.80
88.9
20.00
X
20
0.50
1.30
-
1.40
.051
-
.055
2.20
2.80
57.8
13.00
X
Air Crimp Tool Head
Doc No: ATS-640073500 Release Date: 06-08-04 UNCONTROLLED COPY Pa e 2 of 6
Revision: B Revision Date: 07-05-06
Figure 1
WIRE AGAINST
LOCATOR BLADE
WIRE
TERMINAL
Figure 3
LOCATOR
WIRE
CONDUCTOR
PUNCH
INSULATION
ANVIL
CONDUCTOR
ANVIL
INSULATION
PUNCH
LOCATOR
BLADE
LOCATOR
BLADE
JAWS
OPEN
SAFETY
SHIELD
LOCATOR
Figure 2
PUSH UP
TO LOAD
TERMINAL
Notes:
1. This tool should only be used for the terminals and wire au es
specified on this sheet.
2. This tool is not adjustable for crimp hei ht. Variations in tools,
terminals, wire strandin s and insulation types may affect crimp hei ht.
3. This tool is intended for standard conductor sizes. It may not ive a
ood insulation crimp support for all insulation sizes and types.
4. Pull force should be used as the final criteria for an acceptable crimp.
Pull force is measured with no influence from the insulation crimp. The
insulation should be stripped lon 12.7mm (1/2”) so the insulation rips on the terminal do not rip the
insulation on the wire or the conductor. Refer to the Molex Quality Crimpin Handbook 63800-0029 for
additional information on crimpin and crimp testin .
Operation
Refer to the instruction manual for the 19279-0001 (AT-200) for mountin this crimp tool head.
Caution: Never operate this tool without the supplied safety shield in place. Never place fin ers in the tool nests.
Crimping Terminals
1. Push up on the locator blade and position the terminal with the barrel facin up into the correct die profile
A,B, or C), centerin the barrel in the lower jaw as shown in Fi ure 1 and Fi ure 2. Release the locator
blade to hold the terminal in position.
2. Insert the properly stripped wire into the terminal barrel. See Fi ure 2.
3. Place a wire into the terminal and up a ainst the locator blade. See Fi ure 3. Cycle the tool.
4. Lift up on the locator blade or wire stop and remove the crimped terminal. Inspect for proper crimp location.
Air Crimp Tool Head
Doc No: ATS-640073500 Release Date: 06-08-04 UNCONTROLLED COPY Pa e 3 of 6
Revision: B Revision Date: 07-05-06
Maintenance
It is recommended that each operator of the tool be made aware
of, and responsible for, the followin maintenance steps:
1. Remove dust, moisture and other contaminants with a clean
brush, or soft, lint-free cloth.
2. Do not use any abrasive materials that could dama e the
tool.
3. Make certain all pins; pivot points and bearin surfaces are
protected with a thin coat of hi h quality machine oil. Do
not oil excessively. The 64007-3500 was en ineered for
durability, but like any fine piece of equipment it needs
cleanin and lubrication for a maximum service life of trouble-free crimpin . Use a li ht oil such as 30
wei ht automotive oil used at the oil points shown in Fi ure 4, every 5,000 crimps or monthly will
si nificantly enhance the tool life and ensure a stable calibration.
4. When the tool is not in use store the tool in a clean, dry area.
Warranty
This tool is for electrical terminal crimpin purposes only. This tool is made of the best quality materials. All vital
components are lon life-tested. All tools are warranted free of manufacturin defects for a period of 30 days
Should such a defect occur, we will repair or exchan e the tool free of char e. This repair or exchan e will not
be applicable to alter, misused, or dama ed tools. This tool is desi ned for hand use only. Any clampin ,
fixturin , or use of handle extensions voids this warranty.
Hand held crimpin tools are intended for low volume, prototypin , or repair requirements only.
CAUTION: Molex crimp specifications are valid only when used with Molex terminals, applicators and toolin .
LUBRICATION POINTS
(BOTH SIDES) LIGHT OIL
(EVERY MONTH
OR 5,000 CRIMPS)
Figure 4
Air Crimp Tool Head
Doc No: ATS-640073500 Release Date: 06-08-04 UNCONTROLLED COPY Pa e 4 of 6
Revision: B Revision Date: 07-05-06
PARTS LIST
Item
Order No
Description
Quantity
64007
-
3500
Crimp Tool Head
Fig
ure
5
1
64005
-
0130
Basic Air Tool Head
1
2
63811
-
3575
Locator Assembly
1
3
63811
-
3570
Toolin Kit
1
Tooling Kit Only
4
N/A
Conductor Punch
1
5
N/A
Conductor Anvil
1
6
N/A
Insulation Punch
1
7
N/A
Insulation Anvil
1
8
N/A
4.08 Dia. by 10mm Lon
Dowel Pins
2**
9
N/A
4.08 Dia. by 12.5mm Lon Dowel Pins
2**
10
N/A
.25 I.D. by .357 O.D. by .005” Thick Washer
2**
** Available from an Industrial supply company such as MSC (1
-
800
-
645
-
7270).
REF
637002803
2
3
1
Figure 5
6
M4 NYLON HEX NUT
(2)
8
5
7
9
4
M4 NYLON HEX NUT
M4 FLAT WASHER
(2)
10
(2)
Air Crimp Tool Head
Doc No: ATS-640073500 Release Date: 06-08-04 UNCONTROLLED COPY Pa e 5 of 6
Revision: B Revision Date: 07-05-06
Figure 6
3
4
2
2
2
1
6
(4)
(4)
(
2)
(4)
2
2
(2)
(2)
2
7
(2)
5
Parts List (Continued)
Item
Order No
Description
Quantity
64005
-
0130
Basic Air Tool Head
Fig
ure
6
1
64005
-
0103
Nose Guard
1
2
64000
-
0077
Repair Kit (Sprin s, Rods Pivots ,Rin s, and Washers)
1
3
N/A
M4 by 20 L
on
Freedrive Pan Head Screw
1**
4
N/A
M4 by 25 L
on
Freedrive Pan
Head Screw
1**
5
N/A
3/16” by 3/8” Lon Dowel Pin
1**
6
N/A
Nylon Hex Nut M4 by 0.70mm
2**
7
N/A
M4 Flat Washer
1**
** Available from an Industrial supply company such as MSC (1
-
800
-
645
-
7270).
Air Crimp Tool Head
Doc No: ATS-640073500 Release Date: 06-08-04 UNCONTROLLED COPY Pa e 6 of 6
Revision: B Revision Date: 07-05-06
Air Powered
Crimp Tool Head
Certificate of Calibration
Order No 64007-3500
Tool Order Number -----------------------------
Tool En . Number -----------------------------
Tool Revision ----------------------------
Serial Number -----------------------------
Date of Manufacture ----------------------------
Pin Gau e of Conductor Nest/Nests or Slu hei ht if the nest is the “F” Crimp style.
Ran e Conductor Nest # 1 = -------------------- Actual = --------------------
Ran e Conductor Nest # 2 = -------------------- Actual = --------------------
Ran e Conductor Nest # 3 = -------------------- Actual = --------------------
Technician --------------------
Date of Calibration --------------------
Calibration should be done every 5,000 cycles or 3 months.
Tools should be lubricated durin this operation.
Visit our Web site at http://www.molex.com
Altri manuali per 207129 Series
100
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali molex Utensili per crimpatura
molex
molex 63811-9370 Manuale utente
molex
molex AT-200 Manuale
molex
molex 63811-7000 Manuale utente
molex
molex 63827-2970 Manuale utente
molex
molex 63819-7670 Manuale utente
molex
molex 63811-6670 Manuale utente
molex
molex 63903-8900 Manuale utente
molex
molex 207129 Series Manuale utente
molex
molex 63827-6070 Manuale utente
molex
molex 63816-0900 Manuale utente
molex
molex 207129 Series Manuale utente
molex
molex 207129 Series Manuale utente
molex
molex 207129 Series Manuale utente
molex
molex CR60622B Manuale utente
molex
molex 207129 Series Manuale utente
molex
molex 63816-1100 Manuale utente
molex
molex 35745 Series Manuale utente
molex
molex 63828-0600 Manuale utente
molex
molex 63811-5800 Manuale utente
molex
molex CR1031E Manuale utente
Manuali Utensili per crimpatura popolari di altre marche
Textron
Textron ESG105L Manuale utente
Tyco Electronics
Tyco Electronics 90035-3 Manuale utente
Emerson
Emerson Klauke ES 20RMCCFB Manuale utente
Continental Refrigerator
Continental Refrigerator PC150HD Manuale utente
TE Connectivity
TE Connectivity ERGOCRIMP 1-1579001-3 Manuale utente
Tyco Electronics
Tyco Electronics CERTI-CRIMP 90418-1 Manuale utente