Molex 63827-3070 Manuale utente

Hand Crimp Tool for Solder Right In-Board Terminals

Doc No: ATS-63 2730HM Release Date: 0 -14-14 UNCONTROLLED COPY Page 1 of 6

Revision: A Revision Date: 0 -14-14

INSULATION CRIMP

BRUSH

STRIP LENGTH

BELL MOUTH

CONDUCTOR

CRIMP HEIGHT

SEAM

CUT

OFF

TAB

WIRE

Application Tooling

Sp cification Sh t

Modular Crimp H ad

Ord r No. 63827-3070

Hand Crimp Tool

Ord r No. 63827-3000

FEATURES

% A full cycle ratcheting hand tool ensures complete crimps

% Ergonomically designed soft handles

% Precisely designed crimping profiles with simple contact positioning

% Easy handling due to outstanding force ratio

% Modular Crimp Head is removable and can be use in the Air Powered Tool Order No.63 16-0100,

accompanied by Air Powered Crimp Adapter (Order No. 63 16-0700).

% Can also be used in the Battery Powered Tool Order No.63 16-0200 (110 V) or 63 16-0250 (220 V),

accompanied by Battery Powered Crimp Adapter (Order No. 63 16-0600).

SCOPE

Products: Solder Right In-Board Terminals, 14-16 AWG.

T rminal

S ri s No.

T rminal Ord r No.

Wir Siz

♦

Insulation Diam t r

UL1007 Wir is R comm nd d Strip L ngth

IPC/WHMA

A620 (1)

T rminal

AWG

mm²

In.

172249

0100

2.40

2.79

.094

.110

5.50

5. 0

.216

.22

(1)

To achieve opti

mum IPC

A620 Class 2 insulation

crimps, use

this insulation OD.

DEFINITION OF TERMS

TYPE 4A

Hand Crimp Tool for Solder Right In-Board Terminals

Doc No: ATS-63 2730HM Release Date: 0 -14-14 UNCONTROLLED COPY Page 2 of 6

Revision: A Revision Date: 0 -14-14

Crimp Sp cification

After crimping, the conductor profiles should measure the following (See Figure 1).

T rminal S ri s No.

Wir Siz

Conductor

Pull Forc Minimum

Profil

Crimp H ight

Crimp

dth

AWG

In.

Lb.

172249

1.72

1. 2

.06

.072

2.50

2.60

.09

.102

11.5

1.50

1.60

.059

.063

2.50

2.60

.09

.102

9.0

S am

shall not be open

and no wire allowed out

of the crimping area

Not s:

1. This tool should only be used for the terminals and wire gauges specified on this sheet.

2. This tool is not adjustable for crimp height. Variations in tools, terminals, wire stranding, and insulation types

may affect crimp height.

3. This tool is intended for AWG conductors with UL1007 insulation. It may not give a good insulation crimp

support for other insulation styles.

4. Molex does not repair hand tools (see Warranty on page 3). The replacement parts listed are the only parts

available for repair. If the handles or crimp tooling is damaged or worn, a new tool must be purchased.

5. Pull force should be used as the final criteria for an acceptable crimp. Refer to Molex Quality Crimping

Handbook 63 00-0029 for additional information on crimping and crimp testing.

6. Molex does not certify crimp hand tools.

OPERATION

Open the tool by squeezing the handles together, at the end of the closing stroke, the

ratchet mechanism will release the handles, and the hand tool will spring open.

Pr paring T rminals for Crimping

The terminals must be cut from the reel as shown. See Figure 2. The carrier strip hole is used to assist in loading

the terminal in position over the crimp anvils. The carrier strip will help maintain terminal position during crimping

and can be broken off after the crimp is complete.

Crimping T rminals

1. Load the terminal with carrier strip into the proper crimp profile.

Make sure the carrier strip pilot hole fits over the positioning pin.

2. Push the wire stop downward (into the tool frame).

3. Place the properly stripped wire into the open terminal barrel.

Push the wire into the tool until the end of the wire contacts the

wire stop, making sure that all wire strands are inside of the

conductor barrel. See Figures 3 and 4.

4. While holding the wire with one hand, slowly squeeze the tool

handles together to close the tool jaws until the ratchet

mechanism releases. At this point the handles can be released

and will spring open.

5. Remove the crimped terminal and inspect for acceptable crimp

attributes.

Not : The tamper proof ratchet action will not release the tool until it

has been fully closed.

Figur 2

POSITIONING

LOCATOR

Figur 3

TERMINA

CARRIER STRIP

WIRE STOP

PUSH DOWN

Hand Crimp Tool for Solder Right In-Board Terminals

Doc No: ATS-63 2730HM Release Date: 0 -14-14 UNCONTROLLED COPY Page 3 of 6

Revision: A Revision Date: 0 -14-14

Figur 5

WIRE IN CONDUCTOR CRIMP

WIRE STOP

OPEN

Maint nanc

It is recommended that each operator of the tool be made aware

of, and responsible for, the following maintenance steps:

1. Remove dust, moisture, and other contaminants with a clean

brush, or soft, lint free cloth.

2. Do not use any abrasive materials that could damage the tool.

3. Make certain all pins; pivot points and bearing surfaces are

protected with a thin coat of high quality machine oil. Do not

oil excessively. The tool was engineered for durability but like

any other equipment it needs cleaning and lubrication for a

maximum service life of trouble free crimping. Light oil (such

as 30 weight automotive oil) used at the oil points, every 5,000

crimps or 3 months, will significantly enhance the tool life.

4. Wipe excess oil from hand tool, particularly from crimping

area. Oil transferred from the crimping area onto certain

terminations may affect the electrical characteristics of an

application.

5. When tool is not in use, keep the handles closed to prevent objects from becoming lodged in the crimping dies,

and store the tool in a clean, dry area.

Pull T st Proc dur

Pull testing is to be done with no influence from the insulation crimp.

Pull testing can be done by the following steps:

1. Open the tool by squeezing the handles together, at the end of the closing stroke, the ratchet mechanism will

release the handles, and the hand tool will spring open.

2. Load the terminal with the carrier strip into the proper profile make sure the carrier strip pilot hole fits over the

positioning pin on the locator.

3. Do Not close the wire stop.

4. Position a wire form the back side of the Hand Tool and into the conductor crimp area only. See Figure 5.

5. Carefully crimp the terminal. Open the tool and remove the crimped terminal.

6. Flatten the crimped (empty) insulation grips. This area will be inserted and held in the pull tester grip.

7. Install crimped terminal into the pull tester as shown to perform the pull test. Be careful not to grip wire brush.

See Figure 6.

TERMINAL

WIRE

INSULATION

PUNCH

CONDUCTOR

ANVIL

INSULATION

ANVIL

Figur 4

CONDUCTOR

PUNCH

LOCATOR

WIRE STOP

PULL TESTER

TERMINAL CLAMP

WIRE

Figur 6

CLAMP THE CARRIER

STRIP AND INSULATION

CRIMP GRIPS INTO THE

PULL TESTER

PULL

TESTER

WIRE CLAMP

Hand Crimp Tool for Solder Right In-Board Terminals

Doc No: ATS-63 2730HM Release Date: 0 -14-14 UNCONTROLLED COPY Page 4 of 6

Revision: A Revision Date: 0 -14-14

Miscrimps or Jams

Should this tool ever become stuck or jammed in a partially closed position, Do Not force the handles open or

closed. The tool will open easily by lifting the ratchet release lever. See Figure 6.

Warranty

This tool is for electrical terminal crimping purposes only. This tool is made of the best quality materials. All vital

components are long life tested. All tools are warranted to be free of manufacturing defects for a period of 30

days. Should such a defect occur, we will repair or exchange the tool free of charge. This repair or exchange will

not be applicable to altered, misused, or damaged tools. This tool is designed for hand use only. Any clamping,

fixturing, or use of handle extensions voids this warranty.

CAUTION: Repetitive use of this tool should be avoided.

CAUTIONS:

1. Manually powered hand tools are intended for low volume or field repair. This tool is NOT intended for

production use. Repetitive use of this tool should be avoided.

2. Insulated rubber handles are not protection against electrical shock.

3. Wear eye protection at all times.

4. Use only the Molex terminals specified for crimping with this tool.

CAUTION: Molex crimp specifications are valid only when used with Molex terminals and tooling.

Applications for th Modular Crimp H ad

WARNING: NEVER operate, service, install, or adjust this Modular Crimp Head without proper instruction and

without first reading and understanding the instructions in the proper Manual or Specification Sheet. See Chart

below for the correct Manual or Specification Sheet.

WARNING: NEVER install tooling or service this tool while it is into any power source. Disconnect the power

by unplugging or turn off the Actuator from its power source.

CAUTION: Keep fingers away from the crimping area when operating this tool. It may cause severe injury.

CAUTION: Wear safety glasses when operating or serving this tool.

Hand Crimp Tool for Solder Right In-Board Terminals

Doc No: ATS-63 2730HM Release Date: 0 -14-14 UNCONTROLLED COPY Page 5 of 6

Revision: A Revision Date: 0 -14-14

MODULAR

CRIMP

HEAD

BATTERY

POWER

CRIMP

ADAPTER

LOCKING

PINS

LOCKING PINS

BATTERY

POWERED

TOOL

AIR

POWER

TOOL

MODULAR

CRIMP HEAD

LOCKING

PINS

LOCKING

PINS

AIR

POWER

CRIMP

ADAPTER

The chart below shows all applications for this Modular Crimp Head.

Modular Crimp H ad

Ord r No.

Tool

Ord r no.

Tool

D scription

Adapt r

Ord r No.

Adapt r

D scription

Figur

No.

63 27-3070

63 16

0000

Hand Crimp Frame (Short)

N/A

63 16

0050

Hand Crimp Frame (Long)

N/A

63 16

0200

Battery Power

Tool (110 V)

63 16

0600

Battery Power Crimp Adapt

63 16

0250

Battery Power

Tool (220 V)

63 16

0600

Battery Power Crimp Adapter

63 16

0100

Air

Tool

63 16

0700

Air Power Crimp Adapter

Applications for th Modular Crimp H ad

Hand Crimp Tool

Batt ry Pow r d Tool

Air Pow r d Tool

Figur

MODULAR

CRIMP

HEAD

LOCKING

PINS

HAND CRIMP

FRAME LONG

OR SHORT

Hand Crimp Tool for Solder Right In-Board Terminals

Doc No: ATS-63 2730HM Release Date: 0 -14-14 UNCONTROLLED COPY Page 6 of 6

Revision: A Revision Date: 0 -14-14

RATCHET

RELEASE LEVER

HANDLE

SPRING

CRIMPING

SPRING (2)

Figur 6

M4 X

LONG BHCS

(2)

PARTS LIST

It m

Ord r Numb r

D scription

Quantity

63 27

Modular

Crimp

Head

1 (

ef)

63 16

Hand Crimp

Frame

(

Long

)

(

ef)

63 27

Locator

Plate

63 16

0001

Locking

63600

0525

Handle Spring

63600

0520

Crimping Spring

Visit our Web site at http://www.molex.com

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali molex Utensili per crimpatura

molex

molex 207129 Series Manuale utente

molex

molex RHT 2251-CC Manuale utente

molex

molex RHT-4753 Manuale utente

molex

molex 207129 Series Manuale utente

molex

molex 207129 Series Manuale utente

molex

molex 207129 Series Manuale utente

molex

molex 63811-7200 Manuale utente

molex

molex 207129 Series Manuale utente

molex

molex 207129 Series Manuale utente

molex

molex 63827-0470 Manuale utente

molex

molex CR60670B Manuale utente

molex

molex 207129 Series Manuale utente

molex

molex AT 1992 Manuale utente

molex

molex 207129 Series Manuale utente

molex

molex 63827-5470 Manuale utente

molex

molex 207129 Series Manuale utente

molex

molex 207129 Series Manuale utente

molex

molex 207129 Series Manuale utente

molex

molex 63811-5800 Manuale utente

molex

molex 207129 Series Manuale utente

molex

molex 64001-5900 Manuale utente

molex

molex 207129 Series Manuale utente

molex

molex 207129 Series Guida utente

molex

molex 207129 Series Manuale utente

Manuali Utensili per crimpatura popolari di altre marche

Panduit

Panduit CT-1000 Guida per l'amministratore

JST

JST CS 10 Manuale utente

Danfoss

Danfoss ET4200 Manuale utente

Tyco Electronics

Tyco Electronics PRO-CRIMPER III Manuale utente

TE Connectivity

TE Connectivity 2063528-1 Manuale utente

Tyco Electronics

Tyco Electronics 69156-1 Manuale utente

CRH

CRH CRL CBLHCT1 Manuale utente

Emerson

Emerson Klauke ES 105CFM Manuale utente

KIMBALL MIDWEST

KIMBALL MIDWEST 27-798 Manuale di istruzioni

Danfoss

Danfoss ET4350 Manuale utente

Milwaukee

Milwaukee M18 Manuale utente

HOGERT

HOGERT HT1P169 Manuale utente

Textron

Textron ESG105L Manuale utente

Tyco Electronics

Tyco Electronics 90035-3 Manuale utente

Emerson

Emerson Klauke ES 20RMCCFB Manuale utente

Continental Refrigerator

Continental Refrigerator PC150HD Manuale utente

TE Connectivity

TE Connectivity ERGOCRIMP 1-1579001-3 Manuale utente

Tyco Electronics

Tyco Electronics CERTI-CRIMP 90418-1 Manuale utente

molex 63827-3070 Manuale utente

Manuali Utensili per crimpatura popolari di altre marche