molex AT-1300 Manuale utente
AT-1300 Air Head Crimp Tool
Doc No. ATS-640070800 Release Date: 07- -03 UNCONTROLLED COPY Page 1 of 6
Revision: B Revision Date: 10-13-06
Air Powered
Crimp Tool Head
Krimptite
Application Tooling
Specification S eet
Order No. 64007
-
0800
Engineering No. AT 1300
FEATURES
Quick-change tool head for the 19 79-0001 (AT- 00)
Tooling kit is interchangeable with other kits in the 64001 and 64003 Series
A precision user-friendly terminal locator wire stop holds terminals in the proper crimping position
Pneumatic powered crimp tools help reduce fatigue and discomfort from repetitive manual crimping
SCOPE
Products: Krimptite™ Flag Ring and Spade Terminals, 14–16 AWG. This tool head is intended for use in the
19 79-0001 (AT- 00) either hand held or with optional bench adapter 19078-0307 (ATBA) and foot switch.
Testing
Mec anical
The tensile test, or pull test, is a means of evaluating the mechanical properties of the crimped connections.
The following charts show the UL specifications for various wire sizes. The tensile strength is shown in
pounds and indicates the minimum acceptable force to break or separate the terminal from the conductor.
Wire Size (AWG)
*UL
-
486 A
16
30
14
50
*UL - 486 A - Terminals (Copper conductors only)
The following is a partial list of the product part numbers and their specifications that this tool is designed to
run. We will be adding to this list and an up to date copy is available on www.molex.com.
Wire Size: 14
–
16 AWG 2.0
0
–
1.30mm²
Terminal No. Terminal Eng No. (REF)
Wire Strip Lengt
Insul
ation Diameter
Max
imum
In.
mm
In.
mm
19041
-
0007
B
-
143
-
06
. 66
6.75
N/A
N/A
19041
-
0009
B
-
143
-
08
. 66
6.75
N/A
N/A
19041
-
001
B
-
143
-
10
. 66
6.75
N/A
N/A
1904
-
0004
B
-
148
-
06
. 66
6
.75
N/A
N/A
1904
-
0006
B
-
148
-
08
. 66
6.75
N/A
N/A
1904
-
0008
B
-
148
-
10
. 66
6.75
N/A
N/A
AT-1300 Air Head Crimp Tool
Doc No. ATS-640070800 Release Date: 07- -03 UNCONTROLLED COPY Page of 6
Revision: B Revision Date: 10-13-06
Operation
Refer to the instruction manual for the 19 79-0001 (AT- 00) for mounting this crimp tool
head.
Crimping Terminals
1. Slip the ring or spade of the flag terminal under the locator tab and center the
terminal barrel into the conductor punch of the lower jaw. Make sure the open side
of the barrel is facing down. See Figure 1.
Caution: Never operate this tool without the supplied safety shield in place. Never place fingers in the
tool nests.
. Insert the properly stripped wire into the terminal barrel. See Figure 3.
3. Push on the wire to assure it is fully seated in the terminal. See Figure and 3. Cycle the tool.
4. Remove the crimped terminal. Inspect for proper crimp.
Note: Whenever crimping without the locator, make sure the seam of the terminal is oriented up or down
in the tool if using unbrazed product, as this will provide higher pull force values.
Figure 1
LOCATOR
TAB
TERMINAL
WIRE
TERMINAL
Figure 2
JAWS
OPEN
SAFETY
SHIELD
LOCATOR
TERMINAL
WIRE
CONDUCTOR
PUNCH
Figure 3
CONDUCTOR
ANVIL
AT-1300 Air Head Crimp Tool
Doc No. ATS-640070800 Release Date: 07- -03 UNCONTROLLED COPY Page 3 of 6
Revision: B Revision Date: 10-13-06
“
X ”
NOT POSSIBLE TO PIN GAUGE, MEASURE A
CRIMPED UNINSULATED TERMINAL OR SLUG*
*SOLDER, LEAD
OR
SIMILAR SOFT METAL
Maintenance
It is recommended that each operator of the tool be made aware of,
and responsible for, the following maintenance steps:
1. Remove dust, moisture and other contaminants with a clean
brush, or soft, lint-free cloth.
. Do not use any abrasive materials that could damage the tool.
3. Make certain all pins, pivot points and bearing surfaces are
protected with a thin coat of high quality machine oil. Do not oil
excessively. This tool was engineered for durability, but like any
fine piece of equipment it needs cleaning and lubrication for a
maximum service life of trouble-free crimping. Use a light oil
such as 30 weight automotive oil at the oil points shown in
Figure 4, every 5,000 crimps or monthly will significantly enhance the tool life and ensure a stable
calibration.
4. When tool is not in use store the tool in a clean, dry area.
Tool Calibration
A Certificate of Calibration (see last page) was supplied with the tool. To recalibrate this tool, measurements
should be taken from each conductor nest and compared to this chart. The tool should be lubricated prior to
recalibration to ensure consistent measurements.
Nest Color Code
Wire Range
“X” Dimension Conductor Crimp
Crimp Inspection Marking
AWG
mm²
Mean
Go
No Go
Blue
14
-
16
.00
–
1.30
.093
.089
.101
---
Warranty
This tool is for electrical terminal crimping purposes only. This tool is made of the best quality materials. All
vital components are long life tested. All tools are warranted to be free of manufacturing defects for a period of
30 days. Should such a defect occur, we would repair or exchange the tool free of charge. This repair or
exchange will not be applicable to altered, misused or damaged tools.
CAUTION: Molex crimp specifications are valid only when used with Molex terminals, applicators and tooling.
LUBRICATION POINTS
(BOTH SIDES)
LIGHT OIL (EVERY MONTH
OR 5,000 CRIMPS)
Figure 4
AT-1300 Air Head Crimp Tool
Doc No. ATS-640070800 Release Date: 07- -03 UNCONTROLLED COPY Page 4 of 6
Revision: B Revision Date: 10-13-06
2
3
1
Figure 5
#4 40 X 1/8 LONG
BHSC
4
5
PARTS LIST
Item
Order No
Description
Quantity
64007
-
0800
Crimp Tool Head
Fig
ure
5
1
64005
-
0000
Basic Air Tool Head
1
64003
-
0875
Locator Assembly
1
3
64003
-
0870
Tooling Kit
1
Tooling Kit Only
4
64003
-
080
Conductor Anvil
1
5
64003
-
080
1
Conductor Punch
1
AT-1300 Air Head Crimp Tool
Doc No. ATS-640070800 Release Date: 07- -03 UNCONTROLLED COPY Page 5 of 6
Revision: B Revision Date: 10-13-06
Figure 6
3
3
2
2
2
4
1
(4)
(4)
(
2)
(4)
2
2
(2)
(2)
2
Parts List (Continued)
Item
Order No.
Description
Quantity
64005
-
0000
Basic Air Tool Head
Fig
ure
6
1
64005
-
0103
Nose Guard
1
64000
-
0077
Repair Kit (Springs, Rods Pivots, Rings, and Washers)
1
3
N/A
M4 by 1
L
ong
Freedrive Pan Head Screw
**
4
N/A
3/16” by 3/8” Long Dowel Pin
1**
** Available from an Industrial supply company such as MSC (1
-
800
-
645
-
7 70).
AT-1300 Air Head Crimp Tool
Doc No. ATS-640070800 Release Date: 07- -03 UNCONTROLLED COPY Page 6 of 6
Revision: B Revision Date: 10-13-06
Air Powered
Crimp Tool Head
Krimptite
Certificate of Calibration
Order No. 64007
-
0
8
00
Engineering No. AT 1300
Tool Order Number _______________
Tool Eng. Number ________________
Tool Revision ___________________
Serial Number __________________
Date of Manufacture ______________
Pin Gauge of Conductor Nest/Nests or Slug height if the nest is the “F” Crimp style.
Range Conductor Nest # 1 = ___________ Actual = ___________
Technician _____________________
Date of Calibration ________________
Calibration should be done every 5,000 cycles or 3 months.
Tools should be lubricated during this operation.
Visit our Web site at http://www.molex.com
Indice
Altri manuali molex Utensili per crimpatura
molex
molex AT 2100 Manuale utente
molex
molex HCS-125 Series Manuale utente
molex
molex AT 2080 Guida utente
molex
molex 63819-4100 Manuale utente
molex
molex 63811-8200 Manuale utente
molex
molex 207129 Series Manuale utente
molex
molex 4D Guida utente
molex
molex 63816-0200 Manuale utente
molex
molex 63825-7570 Manuale utente
molex
molex 207129 Series Manuale utente
molex
molex 63825-9700 Manuale utente
molex
molex 4D Manuale utente
molex
molex CR60930B Manuale utente
molex
molex 207129 Series Manuale per l'uso e la cura
molex
molex 207129 Series Manuale utente
molex
molex CR5907 Manuale utente
molex
molex 63825-6770 Manuale utente
molex
molex AT 2212 Manuale utente
molex
molex 63825-7470 Guida utente
molex
molex AT 1992 Manuale utente
Manuali Utensili per crimpatura popolari di altre marche
Textron
Textron ESG105L Manuale utente
Tyco Electronics
Tyco Electronics 90035-3 Manuale utente
Emerson
Emerson Klauke ES 20RMCCFB Manuale utente
Continental Refrigerator
Continental Refrigerator PC150HD Manuale utente
TE Connectivity
TE Connectivity ERGOCRIMP 1-1579001-3 Manuale utente
Tyco Electronics
Tyco Electronics CERTI-CRIMP 90418-1 Manuale utente