Monster MLB7-1037 Manuale utente
INDOOR/OUTDOOR
16.4ft(5m) LED LIGHT STRIP
MODEL MLB7-1037
V1.0 0420
Operation Manual
Features
What’s Included
Introduction
• 16.4ft (5m) length - perfect for lighting decks, walkways,
gardens, and more
• Waterproof LED light strip design is safe for both indoor
and outdoor/wet environment use
• 8ft adapter cable easily reaches from outlet to the
desired location
• Included mounting clips and screws for easy installation
• Multi-color/multi-white color changing and flash modes
• Remote control works up to 26 feet away
This 16.4ft(5m) Indoor/Outdoor LED Light Strip light is
ideal for edge-lighting your deck or railings, or highlighting
gardens and walkways, and gives you the look of
professional lighting while enhancing the style and safety
of your outdoor living spaces.
• 16.4ft (5m) Indoor/Outdoor Led Light Strip
• IR Remote Control
• Mounting Clips x10 (screws x20)
• User Manual
• Keep these instructions.
• Do not drop, puncture, or disassemble this product.
• The plug on the power supply unit must be connected
to a GFCI protected hooded flush type cover plate
receptacle marked “Wet Location” while in use outdoors.
• This LED light strip is suitable for use in wet locations.
DO NOT SUBMERGE THE STRIP OR THE POWER
SUPPLY UNIT IN WATER.
• This product has a polarized plug and will only fit in a
polarized outlet. Do not attempt to defeat this safety
feature. Do not alter the plug.
Please read and understand all instructions before using
this product. If damage is caused by failure to follow the
instructions, this warranty is null and void.
Safety
Instructions
• Use only with an extension cord rated for outdoor use.
Use only three-wire outdoor extension cords that have
three-prong grounding plugs and grounding receptacles
that accept the appliance’s plug. Never use with an
extension cord unless the plug can be fully inserted.
WARNING: When using outdoor use products, basic
safety precautions should always be followed to
reduce the risk of fire, electric shock, and personal
injury, including the following:
• Do not expose this product to open flames or use near fire.
• Do not use the product in a strong magnetic field.
• Use a clean, soft cloth to clean. Do not use any corrosive
cleaners/oils to clean.
• Do not attempt to repair the device or open the unit as this
will void the warranty.
Specifications
• light strip length: 16.4ft (5m)
• cable length:
8ft (2.4m) to power supply + 1.5ft (.5m) to plug
• input: 12V 0.42A
• output: 12V 1A
• remote control: 1 x 3V battery, type CR2025
NOTE: You cannot connect additional light strips to this
product.
NOTE: If desired, you can cut the light strip to shorter
lengths by cutting on the designated scissors marks.
However, IF THE PRODUCT HAS BEEN CUT IT
WILL NO LONGER BE WATER PROOF.
Get Started
1
4
3
Determine where you will install the Indoor/Outdoor
LED Light Strip. Make sure the location is close
enough to a power source for the cord to reach
without becoming a tripping hazard.
2Using the included mounting clips and screws, mount
the Light Strip in the desired location. For best results
place one clip approximately every 20”, or 5 scissors
marks, to secure the entire light strip evenly.
Note: Move some mounting clips closer to corners to better
secure the strip around turns, use fewer on straight areas.
Once installed, connect the power adapter to a powered
outlet. (Outdoors this must be a GFCI protected outlet.)
Remove the protective tab from the battery compartment
of the remote. You are now ready to use your product.
x5 (20”)
TIP: If the power adapter doesn’t reach to the
ground from the outlet, use the keyhole hanger
and a screw or nail to hang it.
MODEL MLB7-1037
V1.0 0420
Operation Manual
①
②
③
④
⑤
⑥
⑦
⑧
Controls, at a Glance
ON/OFF
MULTI-WHITE SELECTORS
MULTI-COLOR SELECTORS
FLASH
STROBE
FADE
SMOOTH
RESET
DIMMER BUTTONS
⑥
Turn the product on and off
Select from cool, soft, or warm white
Change the color to match your mood
Flash color-changing mode
Strobe color-changing mode
Fade color-changing mode
Smooth color-changing mode
Reset to default settings
Adjust the brightness/intensity
④ ⑤ ⑥ ⑦
⑧
⑥
①
②
③
IR Remote IR Receiver
(on adapter housing)
IR Remote
Operation
1
2
Turn on the Indoor/Outdoor LED Light Strip by
pushing the ON button on the remote control.
(It will turn on into the last used lighting mode.)
3Set the desired brightness using the buttons to
increase/decrease the intensity of color.
Select the desired color or effect by pushing
the corresponding button on the remote control.
4Push the OFF button to turn off the Light Strip.
1
2
The battery compartment is located on the narrow
side of the remote control.
3Place the battery compartment back in the remote
control so it locks in place.
Remove the empty battery and insert a 3V battery, type
CR2025, with the positive terminal pointing upwards.
Changing the remote control battery:
Note: The battery for the remote control has already been
installed. Remove the battery pull tab to operate.
Note: For best operation, point the IR remote towards
the IR Receiver (towards power adapter).
Note: You can use this Light Strip with a timer outlet or smart
plug as it will power on into the last used lighting mode.
Notice
FCC Compliance
This device complies with Part 15 of the FCC. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation. Changes or modifications
not expressly approved by the party responsible for compliance could void
the user's authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
RF Exposure Statement
To satisfy FCC’s RF exposure requirements, a separation distance of 20 cm
or more should be maintained between the antenna of this device and
persons during device operation. To ensure compliance, operations at closer
than this distance is not recommended.
Warning
Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s warranty or authority to operate the
equipment.
The M Monster logo is a registered trademark of Monster, Inc. or its
subsidiaries in the U.S. and other countries and is used under license.
Licensed and Manufactured by Jem Accessories, Inc. Edison, NJ 08817
Made in China
Please call for customer support 866-246-2008
Customer
Service
866-246-2008
In the event this product becomes defective,
please do not return this product to your retailer.
Limited
Warranty
If something goes wrong with your product call us toll free at
866-246-2008 for details on how to return your product.
How Do You Get a Replacement?
Any problem that is caused by abuse, misuse, commercial use, exposure
to heat, bright light, sun, liquids sand and other contaminates, contact with
solvents or cleaners, malfunctions caused by other audio equipment or an
act of God (such as a flood) is not covered. Also consequential and
incidental damages and costs of removal or installation is not covered
under this warranty. Some states and countries do not allow the exclusion
of limitation of incidental or consequential damages, so these limitations or
exclusions may not apply to you.
What This Warranty Will Not Cover?
Monster will repair or replace the product for any defective or malfunctioning
product at no charge.
What Will Monster Do?
This warranty lasts as long as you own your Monster product. Coverage
terminates if you sell or otherwise transfer it.
How Long Does the Coverage Last?
This warranty covers any defect or malfunctions in a new Monster product
that you have purchased from an authorized Monster dealer and that comes
with this warranty statement.
What Does This Warranty Cover?
Indice
Altri manuali Monster Luce da lavoro
