Mooreco OneBoard Manuale utente
MooreCo Customer Care Department
1.800.749.2258 - Monday - Friday 8:00am - 5:00pm CST
www.moorecoinc.com/oneboard
Please read, understand, and follow the information contained in
this User Manual before installing and using this product.
Quad User
Owner’s Manual
User Manual - Version 2.0
www.moorecoinc.com | 800.749.2258Page 2 of 23
Contents
Safety Information . . . . . . . . . . . . . . . . . . . . 3
Included with Your OneBoard . . . . . . . . . . . . . . 7
OneBoard Software Installation . . . . . . . . . . . . .8
OneBoard Connection . . . . . . . . . . . . . . . . 10
OneBoard Conguration. . . . . . . . . . . . . . . . 11
OneBoard Software Operation. . . . . . . . . . . . . 13
Notices . . . . . . . . . . . . . . . . . . . . . . . . 21
Warranty . . . . . . . . . . . . . . . . . . . . . . . 22
www.moorecoinc.com | 800.749.2258 Page 3 of 23
800.749.2258 | www.moorecoinc.com
▪Do not use this product in an outdoor environment.
▪Do not use this product near water or moisture. Electric shock may result.
▪This product is not intended for use by unsupervised children. Always provide proper adult supervision when
using this product around children.
▪At least two qualied service technicians should perform the installation and removal procedure. Failure to do
so could result in serious personal injury and/or property damage.
▪Before installation, take the wall material and wall strength into consideration.
▪Always place this product on a stable and level surface.
▪Use only the designated MooreCo stands and wall mounts.
▪Make sure the mounting screws are properly sized to handle the weight of this product.
▪Make sure the mounting hardware is securely anchored to a solid structure.
▪Only plug the power cord or power adaptor into an AC power outlet with the proper and indicated power
supply voltage. Only use grounded AC power outlets. Use of this product with the wrong power supply
voltage may result in property damage, re, or shock.
▪If the power cord or power plug or power adaptor cannot be plugged into the AC power outlet, contact a
licensed electrician to replace the AC power outlet with a properly grounded (earthed) one.
Safety Information
This product was designed for and is intended for use indoor via a USB cable connected to a desktop or laptop
computer. Using this product in an outdoor and/or wet environment could damage this product and create
potentially unsafe conditions.
Meaning of Signal Words
Indicates a potential hazard that could result in serious injury or
death and/or property damage.
Indicates hazards that could result in minor or moderate injury
and/or property damage.
WARNING
CAUTION
Please read, understand and follow all safety information contained in this User Manual before installation and use
of this product:
WARNING WARNING WARNING
www.moorecoinc.com | 800.749.2258Page 4 of 23
▪When you operate this product, the AC power outlet should be near this product and easily accessible.
▪The fact that this product operates satisfactorily does not imply that the AC power outlet is grounded and
that the installation is completely safe. For your safety, if you are in any doubt about the grounding status of
the AC power outlet, consult a qualied electrician.
▪Do not defeat the purpose of the grounded AC power outlet (for example, do not use an outlet converter).
▪Always ensure that the power cord or power adaptor is securely and rmly plugged into the approved AC
power outlet. Otherwise, possible electric shock or re may occur.
▪Do not pull, bend, rest objects on, or chafe the power cord or power adaptor. Damage to the power cord or
power adaptor can cause re or electric shock.
▪Do not attempt to repair the power cord or power adaptor if it becomes damaged. Contact an authorized
service representative for a replacement.
▪Periodically clean the power cord and power adaptor to ensure the connection is free of dust. Always ensure
that the power cord and power adaptor are unplugged before cleaning. Dirty power cord connections or
power adaptor connections may result in a re.
▪Never touch the power cord or power adaptor with wet hands. Electric shock will result.
▪Stop operation immediately if your product emits smoke, excessive heat, abnormal smell or unusual noise.
These conditions may cause re or electronic shock. Immediately turn your product off and unplug the
power cord and/or power adaptor, and contact an authorized service representative for service.
▪When disconnecting this product from an AC power outlet, pull on the power plug and NOT on the power
cord. Pulling on a power cord forcibly can damage it and cause re or electric shock.
▪If an object or liquid get inside this product, turn the product off and unplug the power immediately. Contact
an authorized service representative for service. Operating the contaminated product can cause re or
electronic shock.
▪Never open or remove unit covers that are screwed with screws. A high-voltage component can cause
electric shock.
▪Do not alter this product or modify any parts of the board. Alteration or modication can cause re or
electronic shock
▪Before cleaning this product, unplug the power cord and/or power adaptor. Electric shock may result
otherwise.
▪Do not open or alter the casing of this product. Electric shock or injury may result.
▪Be careful about the location of the power cord, power plug or power adaptor to avoid it tripping someone
or causing this product to fall, etc. It may cause injury or product failure.
▪Do not place this product, power cord, power adaptor, or accessories where it may be tripped on. Failure to
do say may cause injury.
Safety Information (continued)
www.moorecoinc.com | 800.749.2258 Page 5 of 23
800.749.2258 | www.moorecoinc.com
▪Use only the included power cord and power adaptor. If another power cord or power plug or power adaptor
is used, re or electric shock might result.
▪Do not operate this product in a location with high temperature or high humidity. This product is suitable to
work under: Temperature: 10°C to 40°C; Humidity: 10% to 80%; NO condensation.
▪Unplug the power cord, power plug or power adaptor from the AC power outlet when:
The power cord or power supply plug is damaged.
A liquid is spilled onto this product.
This product is exposed to rain or water.
This product malfunctions and/or need repairing.
This product falls or after its cabinet is damaged.
CAUTION CAUTION CAUTION
▪This product must be disposed in accordance with the relevant federal, state, and local laws and
regulations.
▪Do not install this product except by qualied service personnel.
▪Avoid re and heat source above 100°C.
▪When this product is not used over an extended period of time, switch it off and unplug the power plug or
power adaptor. If it is unused and is left connected to a power source for a long period, degraded insulation
may cause electronic shock, current leakage or re.
▪Do not position this product in a location where it is unstable.
▪Do not place this product in a hot, humid or dusty environment. Prolonged exposure to these adverse
conditions may cause re or electric shock.
▪When moving this product, be sure to unplug the power cord, plug or power adaptor from the AC power
outlet. If this product is moved with the power cord or plug or power adaptor attached, it can cause damage
to the power cord, plug or power adaptor which could result in re or electric shock.
▪After installing or moving this product, lock the casters when it is hanging on a mobile stand.
▪If this product is falls down or is damaged, turn this product off and unplug the power cord or power plug or
power adaptor. Otherwise, it may cause re or electric shock.
▪Do not put drinks, other liquids or heavy items on the tray or screen. Accidental spillage of liquid into this
product may cause severe damage. If this occurs, turn this product off, unplug the power cord or power
plug or power adaptor and contact an authorized service representative for service.
▪Do not lean against this product even if this product is mounted on the wall.
▪When this product is not used over an extended period of time, take the batteries out of the electronic
stylus. Otherwise the batteries may leak. Do not use the leaked batteries.
www.moorecoinc.com | 800.749.2258Page 6 of 23
▪Do not install this product where it may be exposed to direct sunlight, near heating equipment, or near air-
conditioning vents.
▪Do not install this product in strong sunlight or strong lighting.
▪Do not install this product in locations where the temperature may change suddenly.
▪Do not erase with a dirty eraser.
▪Use Green Erase whiteboard cleaner for hard-to-erase stains.
▪Fasten the screws tightly to avoid the product falling which may cause injury or damage.
▪Before installation, take the wall material and wall strength into consideration. For details, please consult your
dealer.
Safety Information (continued)
www.moorecoinc.com | 800.749.2258 Page 7 of 23
800.749.2258 | www.moorecoinc.com
Included with Your OneBoard
After unpacking, please make sure all of the following parts (subject to your purchase) are present:
OneBoard - USB
Item Quantity
OneBoard 1
Tray 1
Hardware pack (Z-hanger, side tubes, screws, screw anchors) 1
USB cable 1
Software CD-ROM with user manual 1
Pointers (marker size and pen size) 2
Eraser 1
Wireless USB adapter (wireless kit only) 1
www.moorecoinc.com | 800.749.2258Page 8 of 23
OneBoard Software Installation
DO NOT connect OneBoard USB cable or optional wireless USB adapter to your computer before following the
steps below.
MAC USERS – Download the Mac drivers at www.moorecoinc.com/oneboard under “Software”
Step 1. Install OneBoard software
1. To run the installation program, double-click “OneBoard_Quad_Setup.exe” on your
installation CD. You may see a progress bar initially.
2. Click “Next” to begin installing the software.
3. If prompted, choose the prerequisites to install, click “Next” to continue.
4. Choose the installation destination and click “Next” to continue. You may need to click
“Install” on the next screen.
5. Your installation progress will be displayed.
6. Click “Finish” to exit the installation program after the OneBoard software has been
installed.
www.moorecoinc.com | 800.749.2258 Page 9 of 23
800.749.2258 | www.moorecoinc.com
Wired Boards Only
6. Plug the USB cable into your OneBoard and connect the other end to your PC.
7. The OneBoard has been detected and is ready to use when your computer displays the
following dialog:
8. Once your board is connected for the rst time, you will need to calibrate the software
using the directions on page 12.
Wireless Boards Only
6. Plug the included power adapter into the wall and connect the USB cable to the
OneBoard.
7. Plug the OneBoard USB wireless receiver into your PC.
8. If this is your rst time using the USB wireless receiver or using it with this OneBoard, you
will need to wait for Windows to install the drivers and then open the Wireless Settings
screen. You can nd the Wireless Settings screen by right-clicking the driver icon in the
notication area and choosing “Wireless Settings”.
9. When you rst open the Wireless Settings, it will scan for your OneBoard. Once your
OneBoard has been located, use the “Pair” button to connect your computer and your
OneBoard. Under normal circumstances, you will only need to pair your computer and your
OneBoard the very rst time you use them together. The connection will be automatic from
then on, given that steps 6 and 7 have been followed.
10. Once your board is connected for the rst time, you will need to calibrate the software
using the directions on page 12.
www.moorecoinc.com | 800.749.2258Page 10 of 23
OneBoard Connection
In order to use the OneBoard, you must have a PC or Mac, projector, and OneBoard USB connected as shown
in the gure below. Wireless OneBoards use a USB wireless receiver to connect the OneBoard to the PC.
Once connected, you will need to adjust your projector so that the projected image is fully within the OneBoard
working area.
Wireless OneBoard:
Indice
