Motic SMZ168 Series Manuale utente

Table of Contents

Components ………………………………………………………………………………… 2

Introduction ………………………………………………………………………………… 3

Unpacking …………………………………………………………………………………… 4

Assembly …………………………………………………………………………………… 5

Operation …………………………………………………………………………………… 6

Maintenance ………………………………………………………………………………… 14

Troubleshooting …………………………………………………………………………… 18

Moving the microscope …………………………………………………………………… 19

Repair ……………………………………………………………………………………… 19

Warrantee …………………………………………………………………………………… 19

Components

1. Eyepieces 9. Slide stage clips 17. Support collar

2. Diopter adjuster 10. Stage 18. Column

3. Eyepiece tubes 11. Base 19. On/Off switch

4. Prism housing 12. Power cord for incident

illumination

20. Incident illumination

switch (I)

5. Head holder locking screw 13. Head 21. Transmitted illumination

switch (T)

6. Objectives 14. Zoom knob 22. Light intensity control

7. Incident illumination 15. Head holder

8. Incident light adjustment screw 16. Focus knob

Introduction

Thank you for your purchase of a Motic stereomicroscope. Motic stereomicroscopes are precision

instruments, subjected to meticulous examination to reach you in perfect condition. Their design

combines easy management and optimum functionality with minimum maintenance.

The information contained in this manual is likely to go beyond what the average user needs to

know to use the stereomicroscope, however, it is provided to answer any queries that may arise.

Stereomicroscopes are used to study three-dimensional objects, examine small objects, or dissect

biological specimens. They also permit the observation of slide specimens.

These instructions should be read carefully before operating the microscope. They will permit you

to use your new stereomicroscope to its fullest capabilities. Terminology used to describe

components and controls can be found in the diagram on page 2.

These instructions are based on the assembly and use of the SMZ-168 model with additional notes

specifically for the other models in the series.

Unpacking

All components of the stereomicroscope have been carefully packed to make sure they reach you

in perfect condition. We recommend that you do not discard any of the packing containers in case

you need to return the microscope or store it for long periods of time; or should it become

necessary to transport it to a technical service provider for any repair, or maintenance.

The box should contain the following components:

 SMZ-168 (Binocular) :

An illuminated base with a pole for a moveable head with illumination. A black and white

opaque stage, a binocular head with eyepieces, eyepiece protectors, a frosted glass stage, a blue

filter, a protective cover and a 1.5mm hexagonal key.

 SMZ-168 (Trinocular) :

An illuminated base with a pole for a moveable head with illumination. A black and white

opaque stage, a trinocular head with eyepieces, eyepiece protectors, a frosted glass stage, a

blue filter, a protective cover and a 1.5mm hexagonal key.

Remove and handle all components of the microscope with extreme care.

Avoid touching the lenses of the optical elements and keep them clear of dust, water or other

contaminating agents as they could stain or damage the lens surface affecting the quality of

the image.

Assembly

All the steps described for the assembly of the stereomicroscope must be undertaken with

extreme care and without forcing the placement of the distinct parts and elements of the

stereomicroscope.

A. Place the base of the microscope (11) upright on a flat, stable and clean surface.

B. Loosen the head holder locking screw (5) and place the head (13) in the head holder (15) with

extreme care.

C. Tighten the head holder locking screw (5).

D. Connect the incident illumination to the power cord (12) located at the upper part of the column (18).

Warning: Before connecting the stereomicroscope to a power source, always check that

the output voltage coincides with that of the stereomicroscope.

Operation

A. Starting Up

The stereomicroscope has two stages. One is a frosted glass stage and is used for the

observation of microscope slides or samples that are thin or transparent, such as leaves, insect

wings, etc. The black and white stage is used for non-transparent objects or for dissection. For

the best contrast, choose the side of the stage best suited for your specimen.

Warning: Transmitted illumination can ONLY be used with the frosted glass stage. The

heat generated by the transmitted illumination can melt or damage the black and white

stage. Such damage would not be covered under warrantee.

1. Changing the stage.

a. Using your fingers, remove the stage (10).

b. To use the glass stage, insert the blue filter into the centre of the filter receptacle with the

frosted surface facing down.

c. Replace the glass stage.

2. Before connecting the stereomicroscope to a power source, adjust the light intensity to its

minimum (22). This must be repeated every time the stereomicroscope is turned on or off to

prolong the life of the bulb.

Three light switches are located on the base of the microscope.

MAIN : The principal switch, which turns the whole unit on or off.

I : Turns incident light on or off (illumination from above).

T : Turns transmitted illumination on or off (illumination from below).

3. Turn the principal switch (19) to the ON position.

4. Turn on the incident illumination (20) or transmitted illumination (21) or both at the same

time (“I” and “II”) according to the sample being observed.

5. Light intensity should be adjusted according to the objective used or the type of sample being

observed.

6. The angle of incident illumination can be adjusted by using the adjustment screw (8) which

can be used to vary the orientation of the lens.

B. Interpupillary adjustment

1. Looking through the eyepieces (1), move the eyepiece tubes (3) by taking hold of the prism

housing (4) and moving it outwards or inwards.

2. Interpupillary distance is correct when the two fields of view observed through both

eyepieces appear as one complete field of view.

3. Interpupillary distance should be adjusted for each new user.

C. Focusing

1. Turn the zoom knob (14) to the lowest magnification, 0.75X.

2. Place a flat object or a microscope slide on the centre of the stage (10).

3. Turn the focusing knobs (16) to mid-focus range.

4. The head holder (15) is mounted on a column (18) on which it can be moved up or down

depending on the size of the object to be focused on.

a. Support the head holder (15) with one hand without touching any lenses and with the

other loosen the screw on the support collar (17). The head holder can then be slid to the

base (11).

b. Without letting go of the head, loosen the head holder locking screw. (Fig.1)

Fig.1

c. While looking through the eyepieces, move the head holder up or down until the object

appears in focus.

d. Tighten the head holder locking screw. Do not let go of the head yet.

e. Slide the security collar up to the head holder and tighten the support collar screw. The

head can then be released.

f. It is not necessary to adjust the head every time the sample is changed, only when unable

to bring the image into focus.

5. Adjust the focus knobs (16) until the image appears sharp.

D. Diopter adjustment

Diopter adjustment collars are located on the eyepiece tubes. They are in normal position when

the lower part of the collar is aligned with the sign marked on the eyepiece tube.

To compensate for differences in eyesight:

1. Using only the right eye, look through the right eyepiece (1) and adjust the focus.

2. Next, using the left eye, look through the eyepiece and adjust the focus by turning the diopter

adjuster (2) located on the left-hand tube (3) until the image appears sharp. Do not use the

focus knobs to adjust focus (16).

E. Changing magnification

1. Turn the zoom control (14) to the lowest magnification and bring the image into focus.

Immediately switch to the highest magnification and do the same.

2. The stereomicroscope is now parfocal. However, some minor focus adjustments may have

to be made when switching from a higher strength objective to a lower strength objective.

Switching from a lower strength to higher strength objective should require no focus

adjustment.

Attaching a photographic or video camera (Only for SMZ-168TL)

The SMZ-168 TL model comes equipped with a vertical image port on the head for the

installation of a photographic reflex type camera or video camera, using the corresponding

adapters.

At the back of the head there is a selection lever that transmits the image to the vertical port. When

the lever is opened, the image is transmitted to the vertical port but cannot be seen through the

right eyepiece.

Altri manuali per SMZ168 Series

Indice

Altri manuali Motic Microscopio

Motic

Motic D-Moticam 1080 Manuale utente

Motic

Motic SFC-3 Series Manuale utente

Motic

Motic AE2000 BIN Manuale utente

Motic

Motic K500 Manuale utente

Motic

Motic Moticam Manuale utente

Motic

Motic F-11 LED Series Manuale utente

Motic

Motic AE20 Manuale utente

Motic

Motic BA80 Series Manuale utente

Motic

Motic SILVER30 Series Manuale utente

Motic

Motic BA410 Series Manuale utente

Motic

Motic AE30-31 Manuale utente

Motic

Motic ECO Series Manuale utente

Motic

Motic BA310 Pol Manuale utente

Motic

Motic SWIFTLINE MAE-31R Manuale utente

Motic

Motic SFC-100 Series Manuale utente

Motic

Motic PA43 Manuale utente

Motic

Motic SILVER100 Series Manuale utente

Motic

Motic S-10 Series Manuale utente

Motic

Motic Moticam S2 Manuale utente

Motic

Motic SILVER150 Series Manuale utente

Motic

Motic AE2000MET Manuale utente

Motic

Motic BA310 Pol Manuale utente

Motic

Motic SFC-11 Series Manuale utente

Motic

Motic SWIFTLINE SM100 Series Manuale utente

Manuali Microscopio popolari di altre marche

Thermo Scientific

Thermo Scientific Nicolet iN10 Guida

National

National DC3-163 Manuale utente

KERN Optics

KERN Optics OPE-1 Manuale utente

OPTIKA MICROSCOPES

OPTIKA MICROSCOPES B-150D Manuale utente

Prior

Prior Lux POL Manuale utente

Opitec

Opitec Smartscoop 115615 Manuale utente

KERN

KERN OPO-1 Manuale utente

Topcon

Topcon SP-1P Manuale utente

Leica

Leica DVM5000 Guida utente

MshOt

MshOt MZ62 Manuale utente

KERN Optics

KERN Optics OZR-5 Manuale utente

VWR

VWR VisiScope 384 Series Manuale utente

Nikon

Nikon ECLIPSE E200 POL Manuale utente

Leica

Leica DI C800 Manuale

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Manuale utente

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Manuale utente

Olympus

Olympus SZ61 Manuale utente

Leica

Leica FL560 Manuale utente