Moxa Technologies IEX-408E-2VDSL2-HV Manuale utente

P/N: 1802004082010

*1802004082010*

IEX-408E-2VDSL2 Series

Quick Installation Guide

Moxa Managed VDSL2 Ethernet Extender Switch

Edition 1.0, April 2016

Technical Support Contact Information

www.moxa.com/support

Moxa Americas:

Toll

-free: 1-888-669-2872

Tel:

1-714-528-6777

Fax:

1-714-528-6778

Moxa China (Shanghai office):

Toll

-free: 800-820-5036

Tel:

+86-21-5258-9955

Fax:

+86-21-5258-5505

Moxa Europe:

Tel:

+49-89-3 70 03 99-0

Fax:

+49-89-3 70 03 99-99

Moxa Asia-Pacific:

Tel:

+886-2-8919-1230

Fax:

+886-2-8919-1231

Moxa India:

Tel:

+91-80-4172-9088

Fax:

+91-80-4132-1045



www.ipc2u.ru

www.moxa.pro

Overview

The IEX-408E-2VDSL2 is an industrial managed Ethernet extender switch

for establishing long distance Ethernet transmissions over twisted-pair

copper wiring. IEX-408E-2VDSL2 units can easily be linked in series to

form a long distance multi-drop configuration, with one

IEX-408E-2VDSL2 unit located at each drop-point. Adjacent drop-points

can be separated theoretically by up to 3 km, with a transmission speed of

1 Mbps achieved using a VDSL2 connection (with a connection distance of

300 m, a transmission speed of 100Mbps can be theoretically achieved).

Each IEX-408E-2VDSL2 unit provides six 10/100BaseT(X) and two DSL

ports, giving users an incredible amount of flexibility for linking together

a wide variety of devices separated by vast distances. With its compact

DIN-rail design, the IEX-408E-2VDSL2 series is perfect for use in harsh

operating environments with limited installation space.

Redundancy is provided by Turbo Ring, Turbo Chain, RSTP/STP, and

MSTP, and a state-of-the-art controllable bypass solution on the DSL

ports increases the system reliability and availability of your network.

To simplify configuration, the IEX-408E-2VDSL2 uses CO/CPE automatic

negotiation (the factory default setting). The device will automatically

adjust CO/CPE status to each DSL connection pair of IEX devices to

enable a touch-free of settings.

www.ipc2u.ru

www.moxa.pro

Package List

The Moxa IEX-408E-2VDSL2 is shipped with the following items. If any of

these items are missing or damaged, please contact your customer

service representative for assistance.

•1 IEX-408E-2VDSL2 Extender Switch

•USB Cable: CBL-USBA/B-100

•Protective caps for unused ports

•Documentation and software CD

•Quick installation guide (printed)

•Warranty card

Feature Highlights

•6 10/100BaseT(X) Fast Ethernet ports and 2 DSL (VDSL2 technology)

ports for long distance copper connections (up to 100Mbps @ ~300m

and up to 3km @ ~1Mbps over twisted-pair copper wires)

•Automatic CO/CPE negotiation reduces configuration time

•Turbo Ring / Turbo Chain on both Fast Ethernet and DSL ports for fast

recovery

•Controllable bypass mode on DSL ports gives higher availability in a

daisy chain topology

•Port Trunking on Ethernet and DSL ports for optimum bandwidth

utilization

•RADIUS, TACACS+, SNMPv3, IEEE 802.1X, HTTPS, and SSH to

enhance network security

•Flexible deployment with 2-pin or RJ11/45 connector on DSL ports

•Easy network management by web browser, Telnet/serial console,

Windows utility, ABC-02-USB, and MXview

•Universal power supply options

Universal high-voltage (HV) model (IEX-408E-2VDSL2-HV):

110/220 VDC/VAC (88 to 300 VDC, 85 to 264 VAC)

Redundant dual inputs low-voltage (LV) model

(IEX-408E-2VDSL2-LV): 12/24/48 VDC (9.6 to 60 VDC)

www.ipc2u.ru

www.moxa.pro

IEX-408E-2VDSL2 Panel Layout

Front Panel:

1. USB storage port (type A

connector)

2. 1 to 6: 10/100BaseT(X) port

3. 1 to 6 port status LED

•Upper LED: 100 Mbps

•Lower LED: 10 Mbps

4. System status LED:

•STATE LED indicator

•PWR1 LED indicator

•PWR2 LED indicator

•DSL BYPASS LED indicator

•FAULT LED indicator

•MSTR/HEAD LED indicator

•CPLR/TAIL LED indicator

5. D1 to D2: DSL port

6. DSL port (RJ-45/RJ-11

connector)

7. DSL port (Detachable 2-pin

terminal block)

8. D1 to D2 DSL port st

atus LED:

•CO/CPE LED indicator

•LNK/ACT LED indicator

9. 3-pin-DIP-switch for

controlling DSL Bypass mode

10.

Door screw

11.

Model name

Top Panel

1. RESET button

2. 4-pin terminal receptor for

relay output and digital input

3. USB console port (type B

connector)

4. 4-pin-DIP-switch for Turbo

Ring, Ring Master, and Ring

Coupler

5. Grounding screw (chassis

ground)

6. 5-pin terminal receptor for

power input(s)

•Universal high-voltage

(HV) model

(IEX-408E-2VDSL2-HV):

110/220 VDC/VAC (PWR

•Redundant dual inputs

low-voltage (LV) model

(IEX-408E-2VDSL2-LV):

12/24/48 VDC (PWR 1)

and 12/24/48 VDC (PWR

www.ipc2u.ru

www.moxa.pro

Rear Panel:

Screw holes for wall mounting

kit

2. DIN-rail mounting kit

Mounting Dimensions - unit = mm (inches)

www.ipc2u.ru

www.moxa.pro

DIN-Rail Mounting

The metal DIN-rail mounting kit is fixed to the back panel of the

IEX-408E-2VDSL2. Mount the IEX-408E-2VDSL2 on the corrosion-free

mounting rail that meets the EN 60715 standard.

Installation

STEP 1—Insert the upper lip of

the DIN

-rail kit into the

mounting rail.

STEP 2

—Press the

IEX

-408E-2VDSL2 towards the

mounting rail until it snaps into

place.

Removal

STEP 1—Pull down the latch on

the DIN

-rail kit with a

screwdriver.

STEP 2 & 3

—Slightly pull the

IEX

-408E-2VDSL2 forward and

lift up to remove it from the

mounting rail.

Wall-Mounting (optional)

For some applications, you will find it convenient to mount the Moxa

IEX-408E-2VDSL2 on the wall, as shown in the following figures in this

section. Please follow below illustrations to install.

STEP 1—Remove the DIN rail attachment plate from the rear panel of the

IEX-408E-2VDSL2, and then attach the wall mount plates with M3 screws,

as shown in the figure below.

www.ipc2u.ru

www.moxa.pro

STEP 2—Mounting the IEX-408E-2VDSL2 on the wall

requires 4 screws. Use the

IEX-408E-2VDSL2

, with wall

mount plates attached, as a guide to mark the location

of the 4 screws. The heads of the screws should be less

than 6.0 mm in diameter, and the shafts should be less

than 3.5

mm in diameter, as shown in the figure on

the

right.

NOTE

Before tightening the screws into the wall, make sure the screw

head and shank size are suitable by inserting the screw into one

of the keyhole-shaped apertures of the wall mounting plates.

STEP 3—Do not tighten the screws completely—leave about 2 mm to

allow room for sliding the wall mount panel between the wall and the

screws.

STEP 4—Once the screws are fixed

into the wall, insert the four screw

heads through the large parts of the

keyhole

-shaped ap

ertures, and then

slide the IEX

-408E-2VDSL2

downwards, as indicated in the

figure

the right. Tighten the four

screws for added stability.

Wiring Requirement

ATTENTION

Safety First!

Be sure to disconnect the power cord

before installing and/or

wiring your Moxa Ethernet Extender Switch.

Calculate the maximum possible current in each power wire and

common wire. Observe all electrical codes dictating the

maximum current allowable for each wire size.

If the current goes above the maximum ratings, the wiring could

overheat, causing serious damage to your equipment.

Be sure to read and follow these important guidelines:

•Use separate paths to route wiring for power and devices. If power

wiring and device wiring paths must cross, make sure the wires are

perpendicular at the intersection point.

NOTE

Do not run signal or communications wiring and power wiring

through the same wire conduit. To avoid interference, wires with

different signal characteristics should be routed separately.

•You can use the type of signal transmitted through a wire to

determine which wires should be kept separate. The rule of thumb is

that wiring that shares similar electrical characteristics can be

bundled together.

•You should separate input wiring from output wiring.

•We advise that you label the wiring to all devices in the system.

www.ipc2u.ru

www.moxa.pro

Grounding the Moxa IEX-408E-2VDSL2 Ethernet

Extender Switch

Grounding and wire routing help limit the effects of noise due to

electromagnetic interference (EMI). Run the ground connection from the

ground screw (chassis ground) to the grounding surface prior to

connecting devices.

ATTENTION

This product is intended to be mounted onto a well

-grounded

mounting surface, such as a metal panel.

ATTENTION

Before powering on the IEX

-408E-2VDSL2, make sure that the

grounding cable is secured between the grounding screw (chassis

ground)

and the ground for surge protection (surge ground)

the 5

-pin terminal block for power inputs. Ground for surge

protection is on terminal 3 of the terminal block as shown below.

ATTENTION

For dielectric strength (HIPOT) test, users must remove the

grounding cable secured between the grounding screw (chassis

ground)

and ground for surge protection (surge ground)

located

at terminal 3 of the terminal block to avoid damage.

Wiring the Relay Contact

The IEX-408E-2VDSL2 has one set of relay outputs. These relay output

use two contacts of the 4-pin terminal block on the IEX-408E-2VDSL2’s

top panel.

Refer to the instructions below on how to connect the wires to the

terminal block connector, and how to attach the terminal block connector

to the terminal block receptor.

STEP 1—Insert the two wires into the RELAY terminals respectively to

form an open circuit.

STEP 2—To keep the RELAY wires from coming loose , use a small

flathead screwdriver to tighten the wire-clamp screws on the front of the

terminal block connector.

www.ipc2u.ru

www.moxa.pro

STEP 3—Insert the plastic terminal block connector prongs into the

terminal block receptor, which is located on the IEX-408E-2VDSL2’s top

panel.

FAULT:

The two contacts of the 4-pin terminal block connector are used to detect

user-configured events. The two wires attached to the fault contacts form

an open circuit when a user-configured event is triggered. If a

user-configured event does not occur, the fault circuit remains closed.

Wiring the Digital Input

The IEX-408E-2VDSL2 has one set of digital input (DI). The DI consists of

two contacts of the 4-pin terminal block on the IEX-408E-2VDSL2’s top

panel, which are used for the two DC inputs.

Refer to the instructions below on how to connect the wires to the

terminal block connector, and how to attach the terminal block connector

to the terminal block receptor.

STEP 1: Insert the negative (ground)/positive DI wires into the ┴/I

terminals, respectively.

STEP 2: To keep the DI wires from coming loose, use a small flathead

screwdriver to tighten the wire-clamp screws on the front of the terminal

block connector.

STEP 3: Insert the plastic terminal block connector prongs into the

terminal block receptor, which is located on the IEX-408E-2VDSL2’s top

panel.

Wiring the Power Input (Universal high-voltage

(HV) model: 110/220 VDC/VAC)

The IEX-408E-2VDSL2 HV model (110/220 VDC/VAC) has one set of

power inputs (PWR 1)—Pin 1(V+/Line) and Pin5 (V-/Neutral). Insert the

5-pin terminal block connector prongs into the terminal block receptor on

IEX-408E-2VDSL2 HV unit properly. The top and front views of the

terminal block connector are also shown below.

www.ipc2u.ru

www.moxa.pro

Take the following steps to wire the power input:

STEP 1: Insert the Line/Neutral AC or Positive/Negative DC wires into the

terminals (Terminal 1 for Line/Positive and Terminal 5 for

Neutral/Negative) of the terminal block connector.

STEP 2: To keep the AC or DC wires from coming loose, use a small

flathead screwdriver to tighten the wire-clamp screws on the front of the

terminal block connector.

STEP 3: Insert the plastic terminal block connector prongs into the

terminal block receptor, which is located on the IEX-408E-2VDSL2 HV

unit’s top panel.

NOTE

The IEX-408E-2VDSL2 HV model (110/220 VDC/VAC) has the

reverse protection mechanism for 110/220 VDC input.

ATTENTION

Before connecting the

IEX-408E-2VDSL2 HV model to the DC

power input, make sure the DC power source voltage is stable.

Wiring the Redundant Power Inputs (low-voltage

(LV) model: 12/24/48 VDC)

The IEX-408E-2VDSL2 LV model (12/24/48 VDC) has two sets of power

inputs –power input 1 (PWR 1) and power input 2 (PWR 2). Insert the

5-pin terminal block connector prongs into the terminal block receptor on

IEX-408E-2VDSL2 LV unit properly. Please take the following steps to

wire the redundant power inputs. The top and front views of the terminal

block connector are also shown below.

Take the following steps to wire the redundant power inputs:

STEP 1: Insert the Positive/Negative DC wires into the V1+/V1- terminal

for PWR 1 and/or V2+/V2- terminal for PWR 2.

STEP 2: To keep the DC wires from coming loose, use a small flathead

screwdriver to tighten the wire-clamp screws on the front of the terminal

block connector.

STEP 3: Insert the plastic terminal block connector prongs into the

terminal block receptor, which is located on the IEX-408E-2VDSL2 LV

unit’s top panel.

ATTENTION

Before connecting the

IEX-40E-

2VDSL2 to the DC power inputs,

make sure the DC power source voltage is stable.

www.ipc2u.ru

www.moxa.pro

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Moxa Technologies Interruttore

Moxa Technologies

Moxa Technologies EtherDevice EDS-P510 Series Manuale utente

Moxa Technologies

Moxa Technologies EtherDevice EDS-P206A-4PoE Series Manuale

Moxa Technologies

Moxa Technologies OnCell G3111 Manuale utente

Moxa Technologies

Moxa Technologies PowerTrans PT-7728-PTP Manuale

Moxa Technologies

Moxa Technologies TN-G6512 Serie Manuale utente

Moxa Technologies

Moxa Technologies ToughNet TN-4500A Series Manuale utente

Moxa Technologies

Moxa Technologies EDS-516A Series Manuale

Moxa Technologies

Moxa Technologies PowerTrans PT-7828 Manuale

Moxa Technologies

Moxa Technologies ToughNet TN-4500A Series Manuale utente

Moxa Technologies

Moxa Technologies EDS-G2005-EL Series Manuale utente

Moxa Technologies

Moxa Technologies RKS-G4028 Series Manuale utente

Moxa Technologies

Moxa Technologies ICS-G7526A Series Manuale utente

Moxa Technologies

Moxa Technologies ToughNet TN-5524-8PoE Manuale

Moxa Technologies

Moxa Technologies EtherDevice EDS-516A-T Manuale

Moxa Technologies

Moxa Technologies EDS-4014 Series Manuale utente

Moxa Technologies

Moxa Technologies PT-G7509 Manuale

Moxa Technologies

Moxa Technologies EtherDevice EDS-G205A-4POE-1GSFP-T Manuale utente

Moxa Technologies

Moxa Technologies EtherDevice EDS-4009 Series Manuale utente

Moxa Technologies

Moxa Technologies IKS-G6524 Manuale

Moxa Technologies

Moxa Technologies TN-5508A Series Manuale

Moxa Technologies

Moxa Technologies PT-7528 Manuale

Moxa Technologies

Moxa Technologies EtherDevice Manuale utente

Moxa Technologies

Moxa Technologies EtherDevice EDS-4012 Series Manuale utente

Moxa Technologies

Moxa Technologies EDS-510E Series Manuale utente

Manuali Interruttore popolari di altre marche

URC

URC Total Control MFS-8 Manuale utente

Azbil

Azbil HPQ-D11 Manuale utente

Sony

Sony DFS-900M Manuale utente

SICK

SICK i17S Manuale utente

F&F

F&F SZR-277 Manuale utente

Shure

Shure UAMS/BK Manuale utente

Dräger

Dräger X-zone Switch Off Manuale utente

Asco

Asco Joucomatic 349 Series Manuale utente

BT Mini Hub Manuale utente

D-Link

D-Link DES-1226G Manuale utente

Johnson Controls

Johnson Controls FS80-C Manuale utente

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuale utente

MicroNet

MicroNet SP1200A Manuale utente

Ruijie

Ruijie RG-PF2920 Series Manuale di installazione e funzionamento

Altinex

Altinex DA1914SX Manuale utente

MiLAN

MiLAN MIL-SM2401M Manuale utente

RJM

RJM MASTERMIND PBC/6X Manuale utente

Atlas

Atlas MMK-KVM8 Manuale utente