Moxa Technologies WAC-1001 Series Manuale utente

Reproduction without permission is prohibited.

P/N: 1802010010011

WAC-1001 Series

Quick Installation Guide

Second Edition, May 2014

- 2 -

Overview

The goal of zero-latency-roaming is to allow clients to seamlessly

maintain their communications as they move from one access point to

another. Moxa’s next generation Turbo Roaming technology together

with the WAC-1001 enables 50 ms roaming for enabled AWK-RTG series

devices. This advanced roaming technology delivers high-speed, secure

handoffs within the same subnet and enables clients to roam between APs

in under 50 milliseconds while upholding stringent security in extremely

demanding environments. The WAC-1001 is rated to operate at

temperatures of 0 to 60°C for standard models and -40 to 75°C for

extended temperature models, and is rugged enough for on-site

installation in any harsh industrial environment.

Package Checklist

The WAC-1001 series wireless controller is shipped with the following

items. If any of these items are missing or damaged, please contact your

customer service representative.

•WAC-1001 series wireless controller

•1 cable holder with 1 screw

•2 protective caps

•Wall mount kit

•Quick installation guide

•Software CD

•Warranty card

Installation and Configuration

Before installing the WAC-1001, verify that all items in the Package

Checklist are in the box.

Note that the WAC-1001 must be configured before use. Refer to the

WAC-1001 Series User’s Manual for more details.

The WAC-1001 has a default IP address of 192.168.127.253, which you

must use when connecting to the device for the first time. When

configuring the WAC-1001 for the first time, use the following default user

name and password:

User name: admin

Password: root

ATTENTION

For security reasons, we strongly recommend changing the

default

password. To do so, select Maintenance



Password

and then follow the on

-screen instructions.

To make the change

s effective, you must click Save

Configuration

to save the changes (Restart to apply the

changes).

- 3 -

Panel Layout of the WAC-1001 Series

1. Grounding screw

Terminal block for PWR1, PWR2,

relay, DI1, and DI2

3. Reset button

4. Heat dissipation orifices

System LEDs: PWR1, PWR2, PoE,

FAULT, and STATE LEDs

6. RS-232 console port

7. 10/100BaseT(X) RJ45 Port

8. 10M LED

9. 100M LED

10.

Model name

11.

Screw hole for wall mounting kit

12.

DIN-Rail mounting kit

- 4 -

Mounting Dimensions

DIN-Rail Mounting

The aluminum DIN-Rail attachment plate should already be fixed to the

back panel of the WAC-1001 when you take it out of the box.

If you need to reattach the DIN-Rail attachment plate to the WAC-1001,

make sure the stiff metal spring is situated towards the top as shown in

the figures below.

How to Mount the WAC-1001

STEP 1:

Insert the top of the

DIN-Rail into

the slot just

below the stiff metal

spring.

STEP 2:

Push down to snap the unit into

place.

To remove the WAC-1001 from the DIN-Rail, simply reverse steps 1 and

- 5 -

Wall Mounting

For added convenience, the WAC-1001 can be wall mounted as illustrated

below.

STEP 1:

Remove the aluminum DIN

-Rail

attachment plate from the

WAC-1001

and then attach the wall mount plates

with M3 screws, as shown

on the right

STEP 2:

Mounting the

WAC-1001 to a wall requires 4 screws. Us

the

WAC-1001, with wall mount plates attached, as a

guide to mark the correct locations

for the 4 screws.

The

heads of the screws should be less than 6.0 mm in

diameter, and the

shafts should be less than 3.5 mm in

diameter, as shown on the right.

Do not screw the screws in all the way—leave a space of about 2 mm to

allow room for sliding the wall mount panel between the wall and the

screws.

NOTE

Test the screw’s head and shank size by inserting the screw into

one of the keyhole

-shaped apertures of the wall mounting

plates

before screwing it into the wall.

STEP 3:

After

the screws are fixed into

the wall, insert the four screw

heads through the large opening

of the keyhole

-shaped

apertures, and then slide the

WAC

-1001 downwards, as

indicated

on the right. Tighten

the four screws for added

stability.

- 6 -

Wiring Requirements

WARNING

Safety First!

Be sure the power cord

is disconnected before installing and/or

wiring your WAC-1001.

WARNING

Safety

First!

Calculate the maximum possible current in each power wire and

common wire. Observe all electrical codes dictating the

maximum current allow

ed for each wire size.

If the current goes above the maximum rating, the wiring could

overheat, causing serious damage to your equipment.

You should also pay attention to the following:

•Use separate paths to route wiring for power and devices. If power

wiring and device wiring paths must cross, make sure the wires are

perpendicular at the intersection point.

NOTE: Do not run signal or communications wiring and power wiring

in the same wire conduit. To avoid interference, wires with different

signal characteristics should be routed separately.

•You can use the type of signal transmitted through a wire to

determine which wires should be kept separate. As a rule of thumb,

wiring with similar electrical characteristics can be bundled together.

•Keep input wiring and output wiring separate.

•It is strongly advised that you label wiring to all devices in the system.

ATTENTION

This product is intended to be supplied by a Listed Power Unit

marked “Class 2” or “LPS” and rated O/P: 12 to 48 VDC

Grounding the WAC-1001

Grounding and wire routing help limit the effects of noise due to

electromagnetic interference (EMI). Run the ground wire from the ground

screw to the grounding surface prior to connecting devices.

ATTENTION

This product is

to be mounted to a well-grounded mounting

surface, such as a metal panel.

- 7 -

Wiring the Redundant Power Inputs

Two pairs of contacts of the 10-contact terminal block connector on the

WAC-1001’s top panel are used for the WAC-1001’ two DC inputs. Top

and front views of the terminal block connector are shown here.

STEP 1:

Insert the negative/positive DC wires into the

-/V+ terminals.

STEP 2:

To keep the DC wires from pulling

loose

, use a

small flat

-blade screwdriver to tighten the

wire

-clamp

screws on the front of the terminal

block connector.

STEP 3:

Insert the plastic terminal block connector

prongs into the terminal block receptor, which

located on the WAC-1001’s top panel.

ATTENTION

Before connecting

the WAC-1001

to the DC power inputs, make

sure the DC power source voltage is stable.

Wiring the Relay Contact

The WAC-1001 has one relay output, which consists of two contacts of the

terminal block on the WAC-1001’s top panel. Refer to the previous section

for detailed instructions on how to connect the wires to the terminal block

connector and how to attach the terminal block connector to the terminal

block receptor. These relay contacts are used to indicate user-configured

events. The two wires attached to the relay contacts form an open circuit

when a user-configured event is triggered. If a user-configured event

does not occur, the relay circuit will remain closed.

Wiring the Digital Inputs

The WAC-1001 has two sets of digital inputs—DI1 and DI2. Each DI

consists of two contacts from the 10-pin terminal block connector. Refer

to the “Wiring the Redundant Power Inputs” section for detailed

instructions on how to connect the wires to the terminal block connector,

and how to attach the terminal block connector to the terminal block

receptor.

- 8 -

Cable Holder Installation (Optional)

You may choose to attach the cable holder to the bottom of the

WAC-1001. This helps to keep cabling neat and avoid accidents caused

from cluttered cables.

STEP 1:

Screw the cable holder onto the bottom of the

WAC

-1001.

STEP 2:

After mounting the WAC-1001 and plugging in the LAN cable,

fasten

the cable along the device and wall.

Pin Assignments

10/100BaseT(X) Ethernet Port Connection

The 10/100BaseT(X) ports located on the WAC-1001’s front panel are

used for connecting Ethernet-enabled devices.

Below are the pinouts for both MDI (NIC-type) ports and MDI-X

(HUB/Switch-type) ports.

MDI Port Pinouts

MDI-X Port Pinouts

8-pin RJ45

Signal

Tx+

Rx+

Tx-

Rx-

Rx+

Tx+

Rx-

Tx-

DB9 Male (RS-232) Port Pinouts

The WAC-1001 has one RS-232 (8-pin RJ45) console port located on its

front panel. Use either an RJ45-to-DB9 or RJ45-to-DB25 cable to connect

the WAC-1001’s console port to your PC’s COM port. You may then use a

console terminal program to access the WAC-1001 for console

configuration.

- 9 -

Console Pinouts for 10-pin or 8-pin RJ45

10-Pin

Description

8-Pin

-----

DSR

RTS

GND

TxD

RxD

DCD

CTS

DTR

-----

NOTE

1. The pin numbers for the male DB9 and DB25 connectors,

and hole numbers for the

female DB9 and DB25 connectors

are labeled on the connector. However, the numbers are

typically very small, so you may need to use a magnifying

glass to see the numbers clearly.

2. The pin numbers for both the 8-pin and 10-pin RJ45

connectors (and ports) are typically not labeled on the

connector (or port). Refer to the pinout diagram above to

see how the RJ45’s pins are numbered.

Front Panel LEDs

The WAC-1001’s front panel has seven LED indicators, refer to the

following table for details.

LED

Color

State

Description

Front Panel LED Indicators (System)

PWR1 Green

Power is being supplied from power

input 1.

Off

Power is not being supplied from power

input 1.

PWR2 Green

On Power is being supplied from power

input 2.

Off

Power is not being supplied from power

input 2.

PoE Amber

Power is being supplied via PoE.

Off

Power is not being supplied via PoE.

FAULT

Red

Booting; System Error; Relay is on.

Blinking

(slow)

IP address cannot be obtained from

DHCP server (interval: 1 sec).

Blinking

(fast)

IP address conflict (interval: 0.5 sec).

Off

Normal status.

STATE

Green

/Red

Green

Software Ready

Green

(Blinking)

The WAC-1001 has been located by

Search Utility. (interval: 1sec)

Red

Booting error

- 10 -

LED

Color

State

Description

TP Port LED Indicators (Port Interface)

100M Green

TP port’s 100Mbps link is active

Blinking

Data is being transmitted at 100 Mbps

Off

TP port’s 100Mbps link is inactive.

10M Amber

TP port’s 10Mbps link is active.

Blinking

Data is being transmitted at 10 Mbps

Off

TP port’s 10Mbps link is inactive.

Specifications

WLAN Interface

Standards

IEEE 802.11i for Wireless Security

IEEE 802.3u 10/100BaseT(X) for Ethernet LAN

IEEE 802.3af for Power-over-Ethernet

Security

WPA /WPA2 (IEEE 802.1X/ RADIUS, TKIP and

AES)

Interface

Connection

10-pin removable terminal block

Alarm Contact

1 relay output (1 A @ 24 VDC)

Digital Input 2 electrically-isolated inputs

+3 to -30 V for state “0” (OFF)

+13 to +30 V for state “1” (ON)

Max. input current: 8 mA

Console

RS-232 (RJ45 type)

LAN Port

10/100BaseT(X) auto negotiation speed

LED Indicators

PWR1, PWR2, PoE, FAULT, STATE

Power Requirements

Input Voltage

12 to 48 VDC, redundant dual DC power inputs or

48 VDC Power-over-Ethernet (IEEE 802.3af)

Connector

10-pin removable terminal block

Reverse Polarity

Protection

Present

Physical Characteristics

Housing

Aluminum, providing IP30 protection

Dimensions

53.6 x 135 x 105 mm (2.11 x 5.31 x 4.13 in)

Weight

700 g

Installation

DIN-Rail, wall mounting (with optional kit)

Environmental Limits

Operating Temperature

Standard models: 0 to 60°C (32 to 140°F)

Wide Temp. Models: -40 to 75°C (-40 to 167°F)

Storage Temperature

-40 to 85ºC (-40 to 185ºF)

Ambient Relative

Humidity

5 to 95% (non-condensing)

Regulatory Approvals*

Safety

EN 60950-1, UL60950-1

EMC

FCC Part 15 Subpart B Class B, EN 55022/55024

*Please check Moxa’s website for the most up-to-date certification status.

WARRANTY

5 years

See http://www.moxa.com/warranty

Altri manuali per WAC-1001 Series

Indice

Altri manuali Moxa Technologies Punto di accesso wireless

Moxa Technologies

Moxa Technologies AWK-4121 Manuale utente

Moxa Technologies

Moxa Technologies AirWorks AWK-3131-RCC Series Manuale utente

Moxa Technologies

Moxa Technologies airworks awk-5232 Manuale utente

Moxa Technologies

Moxa Technologies AirWorks AWK-3121-M12-RTG Manuale utente

Moxa Technologies

Moxa Technologies AWK-1121 Manuale utente

Moxa Technologies

Moxa Technologies AirWorks AWK-5222 Manuale utente

Moxa Technologies

Moxa Technologies AirWorks AWK-3121 Manuale utente

Moxa Technologies

Moxa Technologies TAP-6226 Manuale utente

Moxa Technologies

Moxa Technologies AWK-4131 Manuale utente

Moxa Technologies

Moxa Technologies AWK-4121 Manuale utente

Moxa Technologies

Moxa Technologies TAP-213 Manuale utente

Moxa Technologies

Moxa Technologies AirWorks AWK-5222 Manuale utente

Moxa Technologies

Moxa Technologies AirWorks AWK-3191 Manuale utente

Moxa Technologies

Moxa Technologies AirWorks AWK-3251A-M12-RCC Series Manuale utente

Moxa Technologies

Moxa Technologies AWK-6232 Manuale utente

Moxa Technologies

Moxa Technologies AirWorks AWK-1200-AC Manuale utente

Moxa Technologies

Moxa Technologies AirWorks AWK-1131A Manuale utente

Moxa Technologies

Moxa Technologies AirWorks AWK-3121 Manuale utente

Moxa Technologies

Moxa Technologies AWK-4121 Manuale utente

Moxa Technologies

Moxa Technologies AWK-3131 Manuale

Moxa Technologies

Moxa Technologies airworks awk-5232 Manuale utente

Moxa Technologies

Moxa Technologies AirWorks AWK-3121 Manuale utente

Moxa Technologies

Moxa Technologies NPort NWH650 Manuale utente

Moxa Technologies

Moxa Technologies AWK-3121B Series Manuale utente

Manuali Punto di accesso wireless popolari di altre marche

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manuale utente

Ubiquiti

Ubiquiti NanoStation NSM2 Manuale utente

Cisco

Cisco Aironet 1550 Series Manuale utente

Aruba

Aruba IAP-335 Manuale utente

Advantek Networks

Advantek Networks AWN-AP-54MR Manuale utente

IP-COM

IP-COM AP355 Manuale utente

Buffalo

Buffalo AirStation WLA-L11G Manuale utente

EnGenius

EnGenius EnStationACv2 Manuale utente

D-Link

D-Link DAP-3662 Manuale utente

xG Technology

xG Technology xMax CN1300 Manuale utente

Widelink

Widelink ezWave WAP-1100 Series Manuale utente

Edimax

Edimax CAP1200 Manuale utente

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manuale utente

Aruba

Aruba AP-203R Manuale utente

LuXout Shades

LuXout Shades LUXSHADE MOTION Manuale utente

CreatComm

CreatComm TB5F Manuale utente

SineDigital

SineDigital MW-1500AP(H) Manuale utente

TP-Link

TP-Link AP9650 V1 Manuale utente