Multiple Awnings CARROUSEL Manuale operativo
MULTIPLE AWNINGS - 1701, de l’industrie - Beloeil ( uébec) - J3G 4S5
Tel : 450-446-4182 or 1-866-446-4182 - www.multipleawnings.com
Revision as of January 21 2009 Page 1 of 23
USER AND INSTALLATION MANUAL FOR
THE CARROUSEL AWNING
Warning:
PLEASE ENSURE SNOW AND ICE REMOVAL ON STRUCTURE
FOLLOWING A SNOW OR ICE STORM !
FAILURE TO FOLLOW THESE PROCEDURES COULD RESULT IN
INJURY !
•This user and installation guide is a complement to the installation
video. It is highly recommended that you carefully review these
instructions before installing your awning.
•Failure to do so could result in personal injury!
MULTIPLE AWNINGS - 1701, de l’industrie - Beloeil ( uébec) - J3G 4S5
Tel : 450-446-4182 or 1-866-446-4182 - www.multipleawnings.com
Revision as of January 21 2009 Page 2 of 23
INSTALLATION PROCEDURES FOR THE CARROUSEL AWNING
PAGE
TOOLS RE UIRED …………………………………………………………………..………………… 3
LIST OF COMPONENTS
Brackets and hardware ………………………………………………………………….. 4
Walls of structure and roof components …………………………………… 6
FLOOR PREPARATION ………………………………………………………………………………….. 8
ASSEMBLING THE WALLS…………………………………………………………………………… 9
Assembling the 7 large panels……………………………………………………………… 9
Building the 8th panel……………………………………………………………………………. 11
Anchoring the structure to the floor………………………………………………. 13
Installing exterior cappings ………………………………………………………………. 14
ASSEMBLING THE ROOF ……………………………………………………………………………… 15
INSTALLING THE VINYL ROOFING …………………………………………………………… 18
Unfolding the roof ……………………………………………………………………………….. 18
Tightening the vinyl roof using the Flash attachment system® … 19
THE DOOR INSTALLATION…………………………………………………………………………… 21
MULTIPLE AWNINGS - 1701, de l’industrie - Beloeil ( uébec) - J3G 4S5
Tel : 450-446-4182 or 1-866-446-4182 - www.multipleawnings.com
Revision as of January 21 2009 Page 3 of 23
TOOLS RE UIRED
1power drill
1drill bit 5/32’’ *
1 drill bit 3/16’’ for cement *
15/16’’ hex drill bit adaptor*
15/16’’ hex wrench *
1small pry bar
1square drill bit number 1
1square drill bit number 2 *
1 sharp knife (Exacto)
1pair of safety glasses
1metal file
1measuring tape
1chalk line
1rubber mallet
1pair of pliers
1caulking gun
4tubes of 100% silicone ( white or beige)
one 8 foot long ladder
one small 3 foot ladder
* tools included with shipment
MULTIPLE AWNINGS - 1701, de l’industrie - Beloeil ( uébec) - J3G 4S5
Tel : 450-446-4182 or 1-866-446-4182 - www.multipleawnings.com
Revision as of January 21 2009 Page 4 of 23
LIST OF COMPONENTS
Brackets and hardware:
5/16’’ self-tapping screw, ¾’’ long 100
Square roof cubes 8
V bracket for joining panels and anchoring to the floor 8
U bracket for fixing 4
#8 metal screws, square head, 1 ¼’’ long 40
22.5˚ bracket insert for joining upper panels together 8
MULTIPLE AWNINGS - 1701, de l’industrie - Beloeil ( uébec) - J3G 4S5
Tel : 450-446-4182 or 1-866-446-4182 - www.multipleawnings.com
Revision as of January 21 2009 Page 5 of 23
Template representing the leg of a panel 1
Roof crown 2
Cement screws 1 ¼’’ long 8
Door handle complete with screws and lock 1
#6 self taping screws for door hinges, 3/8’’ long 6
#8 pan socket metal screw for door assembly. ¾’’ long 6
MULTIPLE AWNINGS - 1701, de l’industrie - Beloeil ( uébec) - J3G 4S5
Tel : 450-446-4182 or 1-866-446-4182 - www.multipleawnings.com
Revision as of January 21 2009 Page 6 of 23
Door stopper 1
Walls of structure and roof components
Wall panels 78’’ x 56.5 ’’ 7
Side wall panels 78’’ x 10.75’’ 2
Door 1
MULTIPLE AWNINGS - 1701, de l’industrie - Beloeil ( uébec) - J3G 4S5
Tel : 450-446-4182 or 1-866-446-4182 - www.multipleawnings.com
Revision as of January 21 2009 Page 7 of 23
Upper door member 35” with its 2 outside cappings 1
Rafters 1.5’’ x 1.5’’ cube 8
2
1
1
–
Cornices
8
2 - Flash attachment systems 8
3
-
Simple interior
capping
20
4 – Exterior capping 8
3
4
MULTIPLE AWNINGS - 1701, de l’industrie - Beloeil ( uébec) - J3G 4S5
Tel : 450-446-4182 or 1-866-446-4182 - www.multipleawnings.com
Revision as of January 21 2009 Page 8 of 23
FLOOR PREPARATION
Before starting installation, make sure that the floor is level and structurally sound.
Note that the interior dimensions of the octagonal
CARROUSEL
are 136.5 inches.
The minimum overall size required for the platform is 142 inches, which includes an
extra inch all around the awning.
•Start by finding the center of the platform.
•Draw a square figure 136.5’’ x 136.5’’ in the center of the platform with a chalk
line ( see drawing below.)
•The doted lines represent the reference line for positioning the panels during
installation. Remember that these are interior dimensions of the
CARROUSEL
and the panels must rest on the outside of the doted line.
136.5’’
136.5’’
TOP VIEW OF THE FLOOR AREA
______ chalk line, CL : center line
panels
CL
CL
MULTIPLE AWNINGS - 1701, de l’industrie - Beloeil ( uébec) - J3G 4S5
Tel : 450-446-4182 or 1-866-446-4182 - www.multipleawnings.com
Revision as of January 21 2009 Page 9 of 23
ASSEMBLING THE WALLS
Assembling the 7 large panels
•Install the interior cappings on each panel with the use of a rubber mallet (this
step may have been done at the factory prior to shipment.) As a reference, the
screen is always facing outwards and the polymer windows facing inwards. There
are 2 interior cappings per panel. There are a total of 7 large panels and 2 small
side panels.
•Install the cornice on top of each panel with five 5/16’’ self-tapping screws. The
holes have been pre-drilled at the factory for your convenience. The cornice
must be flush and equidistant to each corner as seen in the picture below.
As an example :
Top view
Cornice must be flush
MULTIPLE AWNINGS - 1701, de l’industrie - Beloeil ( uébec) - J3G 4S5
Tel : 450-446-4182 or 1-866-446-4182 - www.multipleawnings.com
Revision as of January 21 2009 Page 10 of 23
•With the help of another person, place 2 panels upright, side by side on the
outskirts of the chalk line you drew on the floor. The angle of the cornices
should align perfectly.
•Install the Flash attachment system® on the cornice of each panel. To do so,
tilt the attachment system as shown so that it hitches on the lip of the cornice,
and then tilt it back straight.
•Slide a 22,5˚ bracket insert in the upper part of the Flash attachment system®
so that it joins both panels together.
•If the floor plan has been properly prepared, the panels should align perfectly.
The 22,5˚ bracket
insert will join both
panels together
Indice
Altri manuali Multiple Awnings Accessori
