National Instruments PXI Series Manuale utente

INSTALLATION GUIDE

PXI and PXI Express Chassis Fan

Replacement

This guide describes how to replace the fan on a PXI and PXI Express

chassis.

Cautions Make sure to unplug the power cord before replacing the fan.

Only trained service personnel should replace the fan.

4–6 and 9 Slot Chassis Fan Replacement

Note Fan replacement is supported only on chassis with specific assembly numbers. The

supported model numbers are listed below, followed by their supported assembly numbers

in parentheses. The xdenotes the assembly letter revision.

Before replacing the fan, be sure to check the model and assembly numbers on the back of

your PXI chassis. Replace the fan only if the model and assembly numbers are on the

following list. Refer to the NI PXI-103x and NI PXIe-1073 Chassis Fan Replacement

section for information about previous revisions.

• NI PXI-1031 (190871x-01, Revision L and newer)

• NI PXI-1031DC (191746x-01, Revision H and newer)

• NI PXI-1033 (194918x-01, Revision E and newer)

• NI PXI-1036 (192592x-01, Revision H and newer)

• NI PXI-1036DC (192593x-01, Revision F and newer)

• NI PXIe-1071 (195659x-01L)

• NI PXIe-1073 (196695x-01, Revision D and newer)

• NI PXIe-1078 (199485x-01L)

Refer to Figure 1 and the following steps for installation and removal

instructions.

Chassis Fan Replacement Guide 2 ni.com

NI PXI-103xand NI PXIe-1073 Chassis Fan Replacement

This section describes how to install the NI PXI-103xchassis fan

replacement kit for the PXI-1031, PXI-1031DC, PXI-1033, PXI-1036,

PXI-1036DC, and PXIe-1073 chassis.

Note Fan replacement is supported only on chassis with specific assembly numbers. The

supported model numbers are listed below, followed by their supported assembly numbers

in parentheses. The xdenotes the assembly letter revision.

Before replacing the fan, be sure to check the model and assembly numbers on the back of

your PXI chassis. Replace the fan only if the model and assembly numbers are on the

following list.

• NI PXI-1031 (190871x-01, Revision H through K)

• NI PXI-1031DC (191746x-01, Revision E through G)

• NI PXI-1033 (194918x-01, Revision A through D)

• NI PXI-1036 (192592x-01, Revision D through G)

• NI PXI-1036DC (192593x-01, Revision C through E)

• NI PXIe-1073 (196695x-01, Revision A through C)

Refer to Figure 5 and the following steps for installation and removal

instructions.

©National Instruments Corporation 3 Chassis Fan Replacement Guide

Figure 1 shows the parts you must remove to access the fan. Refer to the

following steps for installation and removal instructions.

Figure 1. PXI Express Chassis Part Locations (Chassis Shown Upside Down)

Complete the following steps to replace the fan (refer to the previous figure

for parts locations):

1. Locate the fan access panel on the bottom of the chassis. Remove the

access panel screw and the access panel.

2. Remove the two fan shoulder screws, shown in Figure 1, that fasten the

fan. Be careful not to lose the screws.

3. Remove the fan.

1 Fan Shoulder Screw (x2)

2 Fan Access Panel Screw (x1)

3 Fan Access Panel

4Fan

5 Screen (Visible Through Fan)

6 Chassis

Chassis Fan Replacement Guide 4 ni.com

4. Disconnect the fan cable from the inline connector. The connector is

shown in Figure 2.

Figure 2. Fan Cable Inline Connector

1Fan 2 Fan Cable Inline Connector

©National Instruments Corporation 5 Chassis Fan Replacement Guide

5. Connect the new fan to the inline connector. Place the fan inside the fan

bracket with the square slot oriented as shown in Figure 3. The air flow

direction is into the chassis, so the plastic grill and label on the fan

should face toward the PXI card cage.

Place the screen below the fan (see Figure 1 for screen location).

Ensure that the loose screen doesn’t fall out. If the screen does fall out,

return it to its position under the fan.

Figure 3. Square Slot on Fan Housing

6. Reinstall the two shoulder screws.

1 Square Slot on Fan Housing

AIR FLOW

Chassis Fan Replacement Guide 6 ni.com

Figure 4. Thermistor Wire

7. Tighten the shoulder screws to between 3.0 lb · in. minimum torque

and 3.6 lb · in. maximum torque.

Caution Orient the thermistor wire, as shown in Figure 4, before replacing the fan access

panel.

8. Place the fan access panel over the opening. Insert and tighten the

access panel screw to between 3.0 lb · in. minimum torque and

3.6 lb · in. maximum torque.

Caution Reorient the chassis to an upright position and ensure there are no loose parts

prior to plugging in the power cord.

1 Thermistor wire

©National Instruments Corporation 7 Chassis Fan Replacement Guide

Figure 5 shows the parts you must remove to access the fan. Refer to the

following steps for installation and removal instructions.

Figure 5. PXI and PXI Express Chassis Part Locations (Chassis Shown Upside Down)

1 Washers (x3 each)

2 Fan Screw (x4)

3 Fan Access Panel Screw

4 Fan Access Panel

5 Thermistor

6 Thermistor Clip

7 Fan Guard Screen

8 Fan Guard

Chassis Fan Replacement Guide 8 ni.com

Complete the following steps to replace the fan (refer to the previous figure

for parts locations):

1. Locate the fan access panel on the bottom of the chassis. Remove the

access panel screw and the access panel.

2. Remove the four fan screws, shown in Figure 5, that fasten the fan. Be

careful not to lose the screws or washers. (If you lose a screw, replace

it with an M3 ×0.5 ×35 mm pan head Phillips screw.)

3. Remove the thermistor and fan guards.

4. Remove the fan.

5. Disconnect the fan cable from the inline connector protruding through

the grommet in the fan bracket. The connector is shown in Figure 6.

Caution Do not allow the wires to fall through the grommet.

Figure 6. Fan Cable Inline Connector

1 Grommet 2 Fan Cable Inline Connector

©National Instruments Corporation 9 Chassis Fan Replacement Guide

6. Connect the new fan to the inline connector. Place the fan inside the fan

bracket with the square slot oriented as shown in Figure 7. The fan

flow direction is into the chassis, so the plastic grill on the fan should

face toward the PXI card cage.

Figure 7. Square Slot on Fan Housing

7. Place the fan guards on top of the fan with the round wire guard closest

to the fan and the screen guard on top of the round wire guard.

1 Square Slot on Fan Housing

Chassis Fan Replacement Guide 10 ni.com

8. Insert three of the four screws with the flat washers closest to the fan

and the split spring washers closest to the screw heads. The fourth

screw does not use washers, but instead anchors the thermistor. Insert

the fourth screw through the thermistor clip hole and orient the

thermistor as shown in Figure 8.

Figure 8. Thermistor Location and Orientation

9. Tighten the screws to between 5.7 lb · in. minimum torque and

6.7 lb · in. maximum torque.

10. Place the fan access panel over the opening. Insert and tighten the

access panel screw to between 3.0 lb · in. minimum torque and

3.6 lb · in. maximum torque.

Caution Reorient the chassis to an upright position and ensure there are no loose parts

prior to plugging in the power cord.

1 Grommet 2 Thermistor and Clip

Altri manuali per PXI Series

Questo manuale è adatto per i seguenti modelli

Altri manuali National Instruments Telaio

National Instruments

National Instruments cRIO-9068 Manuale utente

National Instruments

National Instruments 9146 Manuale utente

National Instruments

National Instruments NI 9144 Manuale utente

National Instruments

National Instruments PXI 1000B Manuale di installazione

National Instruments

National Instruments NI PXI-1044 Manuale utente

National Instruments

National Instruments CompactRIO cRIO-FRC Manuale utente

National Instruments

National Instruments PXI 1000B Manuale utente

National Instruments

National Instruments cDAQ-9179 Manuale utente

National Instruments

National Instruments cDAQ-9171 Manuale utente

National Instruments

National Instruments NI cRIO-9111 Manuale utente

National Instruments

National Instruments NI PXIe-1071 Manuale utente

National Instruments

National Instruments NI 9144 Manuale utente

National Instruments

National Instruments PXI-1010 Manuale utente

National Instruments

National Instruments PXIe-1086 Manuale utente

National Instruments

National Instruments NI 9144 Manuale utente

National Instruments

National Instruments PXI-1042Q Manuale utente

National Instruments

National Instruments PXI Express PXIe-1071 Manuale utente

National Instruments

National Instruments NI 9148 Manuale utente

National Instruments

National Instruments NI PXI-1050 Manuale utente

National Instruments

National Instruments NI cRIO-9074XT Manuale utente

National Instruments

National Instruments PXI Series Manuale utente

National Instruments

National Instruments Eight-slot USB Chassis NI cDAQ-9172 Manuale utente

National Instruments

National Instruments PXI Express NI PXIe-1073 Manuale utente

National Instruments

National Instruments SCXI-1000 Manuale utente

Manuali Telaio popolari di altre marche

Advantech

Advantech IPC-623 Series Manuale utente

IMC Networks

IMC Networks iMcV/18 Manuale utente

Chenbro

Chenbro RB13804N4WFT Manuale utente

Lenovo

Lenovo ThinkSystem SR665 V3 Manuale utente

Wuntronic

Wuntronic PCI4DRQ Manuale utente

EtherWAN

EtherWAN EMC400 Manuale utente

Overland Storage

Overland Storage SnapSAN S1000 Guida

Philips

Philips LC4.1E A Manuale utente

Supermicro

Supermicro SCF418 Series Manuale utente

Chenbro

Chenbro RM437 Series Manuale utente

Pickering

Pickering 40-914 Manuale utente

HP A7503-S Istruzioni per il montaggio

Supermicro

Supermicro SC823MTQ-R700LPB Manuale utente

SilverStone

SilverStone RMS08 Series Manuale utente

NI cRIO-FRC II Manuale utente

Pickering

Pickering 65-200 Manuale utente

Allied Telesis

Allied Telesis AT-MMCR18 Manuale utente

Hisense

Hisense MSD6586 Manuale utente