National Instruments GPIB-1014 Series Manuale utente

Getting Started with Your GPIB-1014

Series Board and the NI-488M™

Software for Motorola UNIX

May 1992 Edition

Part Number 320509-01

National Instruments Corporate Headquarters

6504 Bridge Point Parkway

Austin, TX 78730-5039

(512) 794-0100

(800) IEEE-488 (toll-free U.S. and Canada)

Technical support fax: (512) 794-5678

Branch Offices:

Australia 03 879 9422, Belgium 02 757 00 20, Canada 519 622 9310,

Denmark 45 76 73 22, France 1 48 65 33 70, Germany 089 714 50 93,

Italy 02 48301892, Japan 03 3788 1921, Netherlands 01720 45761,

Norway 03 846866, Spain 91 896 0675, Sweden 08 984970,

Switzerland 056 45 58 80, U.K. 0635 523545

Limited Warranty

The National Instruments GPIB boards are warranted against defects in

materials and workmanship for a period of two years from the date of

shipment, as evidenced by receipts or other documentation. National

Instruments will, at its option, repair or replace equipment that proves to be

defective during the warranty period. This warranty includes parts and

labor.

The media on which you receive National Instruments software are

warranted not to fail to execute programming instructions, due to defects in

materials and workmanship, for a period of 90 days from date of shipment,

as evidenced by receipts or other documentation. National Instruments will,

at its option, repair or replace software media that do not execute

programming instructions if National Instruments receives notice of such

defects during the warranty period. National Instruments does not warrant

that the operation of the software shall be uninterrupted or error free.

A Return Material Authorization (RMA) number must be obtained from the

factory and clearly marked on the outside of the package before any

equipment will be accepted for warranty work. National Instruments will

pay the shipping costs of returning to the owner parts which are covered by

warranty.

National Instruments believes that the information in this manual is

accurate. The document has been carefully reviewed for technical accuracy.

In the event that technical or typographical errors exist, National

Instruments reserves the right to make changes to subsequent editions of

this document without prior notice to holders of this edition. The reader

should consult National Instruments if errors are suspected. In no event

shall National Instruments be liable for any damages arising out of or

related to this document or the information contained in it.

EXCEPT AS SPECIFIED HEREIN, NATIONAL INSTRUMENTS MAKES NO

WARRANTIES, EXPRESS OR IMPLIED, AND SPECIFICALLY DISCLAIMS

ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A

PARTICULAR PURPOSE. CUSTOMER'S RIGHT TO RECOVER DAMAGES

CAUSED BY FAULT OR NEGLIGENCE ON THE PART OF NATIONAL

INSTRUMENTS SHALL BE LIMITED TO THE AMOUNT THERETOFORE

PAID BY THE CUSTOMER. NATIONAL INSTRUMENTS WILL NOT BE

LIABLE FOR DAMAGES RESULTING FROM LOSS OF DATA, PROFITS,

USE OF PRODUCTS, OR INCIDENTAL OR CONSEQUENTIAL DAMAGES,

EVEN IF ADVISED OF THE POSSIBILITY THEREOF. This limitation of the

liability of National Instruments will apply regardless of the form of action,

whether in contract or tort, including negligence. Any action against

National Instruments must be brought within one year after the cause of

action accrues. National Instruments shall not be liable for any delay in

performance due to causes beyond its reasonable control. The warranty

provided herein does not cover damages, defects, malfunctions, or service

failures caused by owner's failure to follow the National Instruments

installation, operation, or maintenance instructions; owner's modification of

the product; owner's abuse, misuse, or negligent acts; and power failure or

surges, fire, flood, accident, actions of third parties, or other events outside

reasonable control.

Under the copyright laws, this publication may not be reproduced or

transmitted in any form, electronic or mechanical, including photocopying,

recording, storing in an information retrieval system, or translating, in

whole or in part, without the prior written consent of National Instruments

Corporation.

Trademarks

NI-488M™is a trademark of National Instruments Corporation.

Product and company names listed are trademarks or trade names of their

respective companies.

FCC/DOC Radio Frequency Interference Compliance

This equipment generates and uses radio frequency energy and, if not

installed and used in strict accordance with the instructions in this manual,

may cause interference to radio and television reception. This equipment

has been tested and found to comply with the following regulatory agencies:

• The limits for a Class A computing device, in accordance with the

specifications in Part 15 of U.S. Federal Communications Commission

(FCC) Rules. Operation is subject to the following two conditions:

– This device may not cause harmful interference.

– This device must accept any interference received, including

interference that may cause undesired operation.

• The limits for radio noise emissions from digital apparatus set out in

the Radio Interference Regulations of the Canadian Department of

Communications (DOC).

These regulations are designed to provide reasonable protection against

interference from the equipment to radio and television reception in

commercial areas.

There is no guarantee that interference will not occur in a particular

installation. However, the chances of interference are much less if the

equipment is used according to this instruction manual.

If the equipment does cause interference to radio or television reception,

which can be determined by turning the equipment on and off, one or more

of the following suggestions may reduce or eliminate the problem.

• Operate the equipment and the receiver on different branches of your

AC electrical system.

• Move the equipment away from the receiver with which it is

interfering.

• Relocate the equipment with respect to the receiver.

• Reorient the receiver's antenna.

• Be sure that the equipment is plugged into a grounded outlet and that

the grounding has not been defeated with a cheater plug.

Notice to user: Changes or modifications not expressly approved by

National Instruments could void the user's authority

to operate the equipment under the FCC Rules.

If necessary, consult National Instruments or an experienced

radio/television technician for additional suggestions. The following

booklet prepared by the FCC may also be helpful: How to Identify and

Resolve Radio-TV Interference Problems. This booklet is available from

the U.S. Government Printing Office, Washington, DC 20402, Stock

Number 004-000-00345-4.

Preface

This manual contains instructions for installing and configuring the

National Instruments GPIB-1014 series interface boards and the NI-488M

multitasking software for use with the Motorola UNIX Operating System.

This manual is meant to be used with the National Instruments IEEE 488

Multitasking UNIX Device Driver reference (NI-488M Software Reference

Manual, part number 320062-01).

The material in this manual is for users who have extensive knowledge of

the Motorola UNIX operating system and have super-user privilege. This

manual also assumes that the user has already received a GPIB-1014 series

interface board along with a user manual.

Organization of This Manual

This manual is organized as follows:

Chapter 1, Introduction, briefly describes the GPIB-1014 series interface

boards and the NI-488M software, and lists the contents of your NI-488M

kit and optional equipment.

Chapter 2, Installation and Configuration,lists all the files located on the

distribution medium, and contains step-by-step instructions for configuring

and installing the NI-488M software and GPIB-1014 series interface boards,

and verifying the software installation.

Appendix A, Troubleshooting, suggests areas to check if you still have

problems installing the GPIB-1014 series boards and/or the NI-488M

software after following the procedures described in Chapter 2, Installation

and Configuration.

Appendix B, Customer Communication, contains forms for you to complete

to facilitate communication with National Instruments concerning our

products.

Preface

1014/NI-488M/Motorola UNIX viii © National Instruments Corp.

Conventions Used in This Manual

The following conventions are used throughout this manual.

enter Reserved to mean that the commands

immediately succeeding the word must be typed

into the computer, and then executed by pressing

the <Return> key on the keyboard.

GPIB-1014 Refers to any National Instruments VME-to-

IEEE 488 interface board including the

GPIB-1014, GPIB-1014D, GPIB-1014DP, and

GPIB-1014P.

italic Italic text denotes emphasis, a cross reference, or

an introduction to a key concept.

monospace Lowercase text in this font denotes text or

characters that are to be literally input from the

keyboard, sections of code, programming

examples, and syntax examples. This font is also

used for the proper names of disk drives, paths,

directories, programs, subprograms, subroutines,

device names, functions, variables, filenames,

and extensions, and for statements and comments

taken from program code.

Motorola UNIX Refers to the SYS/V68 release 3 version 5.1

Operating System.

Abbreviations

The following abbreviations for units of measure are used in this manual:

A amperes

Hz hertz

in. inches

kbytes 1,024 bytes

M megabytes of memory

M- mega- (106)

m meters

Preface

Acronyms

The following acronyms are used in this manual:

ANSI American National Standards Institute

DMA direct memory access

GPIB General Purpose Interface (IEEE 488) bus

IEEE Institute of Electrical and Electronic Engineers

I/O input/output

PIO programmed input/output

RAM random-access memory

VDC volts direct current

Note: References in this manual to IEEE 488 are referring to the

ANSI/IEEE Standard 488.1-1987 which defines the GPIB.

Related Documentation

This manual is to be used with the following documentation:

•GPIB-1014 User Manual, National Instruments Corporation

(Part Number 320030-01)

•GPIB-1014D User Manual, National Instruments Corporation

(Part Number 320140-01)

•GPIB-1014DP User Manual, National Instruments Corporation

(Part Number 320049-01)

•GPIB-1014P User Manual, National Instruments Corporation

(Part Number 320026-01)

• ANSI/IEEE Standard 488.1-1987, IEEE Standard Digital Interface for

Programmable Instrumentation

•SYSTEM V/68 Release 3 System Administrator's Reference Manual

(For more information on Motorola UNIX documentation, contact the

Literature Distribution Center, 616 West 24th Street, Tempe Arizona

85282.)

Preface

1014/NI-488M/Motorola UNIX x © National Instruments Corp.

Customer Communication

National Instruments wants to receive your comments on our products and

manuals. We are interested in the applications you develop with our

products, and we want to help if you have problems with them. To make it

easy for you to contact us, this manual contains comment and configuration

forms for you to complete. These forms are in Appendix B, Customer

Communication, at the end of this manual.

Altri manuali per GPIB-1014 Series

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali National Instruments Hardware per computer

National Instruments

National Instruments GPIB-ENET-1000 Manuale utente

National Instruments

National Instruments NI PXIe-8130 Manuale utente

National Instruments

National Instruments NI 9219 Manuale utente

National Instruments

National Instruments PCI-7041 Manuale utente

National Instruments

National Instruments PXI Express NI PXIe-1065 Manuale utente

National Instruments

National Instruments PCMCIA-GPIB Manuale utente

National Instruments

National Instruments CAN PXI-846 Series Manuale utente

National Instruments

National Instruments AT-GPIB/TNT Manuale utente

National Instruments

National Instruments PCI-6601 Manuale utente

National Instruments

National Instruments PXI-8101 Manuale utente

National Instruments

National Instruments PCI-1407 Manuale di istruzioni

National Instruments

National Instruments PCI-6110E/6111E Manuale utente

National Instruments

National Instruments cFP-20xx Manuale utente

National Instruments

National Instruments NI PXI-1042 Series Manuale utente

National Instruments

National Instruments PXI-8186 Manuale utente

National Instruments

National Instruments CPCI-GPIB Manuale utente

National Instruments

National Instruments NI 9213 Manuale utente

National Instruments

National Instruments PXIe-7911 Manuale utente

National Instruments

National Instruments NI PXIe-8130 Manuale utente

National Instruments

National Instruments Multifunction RIO NI R Series Manuale utente

National Instruments

National Instruments 8-Slot PXI Backplane Manuale utente

National Instruments

National Instruments NI PXI-8221 Manuale utente

National Instruments

National Instruments NI PXIe-1062Q Manuale utente

National Instruments

National Instruments NAT7210 Manuale utente

Manuali Hardware per computer popolari di altre marche

EMC2

EMC2 VNX Series Manuale del proprietario

Panasonic

Panasonic DV0PM20105 Manuale utente

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuale utente

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuale utente

Raidon

Raidon iT2300 Manuale utente

Hauppauge

Hauppauge WinTV-HVR-2250 Manuale utente

Kontron

Kontron CP6002 Manuale utente

Manhattan

Manhattan 702843 Manuale utente

Aphex

Aphex 230 Manuale utente

AMD

AMD Phenom II Manuale operativo

Intel

Intel NUC 12 Pro Manuale utente

dbx

dbx Zone Pro 1260 Manuale utente

Galaxy

Galaxy GHDX2-2430S-24F4D Manuale utente

Intel

Intel AXXRMFBU4 Manuale utente

Kontron

Kontron DIMM-PC/MD Manuale utente

ST X-NUCLEO-SAFEA1B Istruzioni operative

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuale utente

Advantech

Advantech ASMB-935 Series Manuale utente