National Instruments FieldPoint cFP-2120 Manuale utente

QUICK START GUIDE

FieldPoint cFP-2120

Mount the Compact FieldPoint Backplane

You can mount the cFP-BP-

backplane on a 35 mm DIN rail, on a panel, or in a

standard 19 in. rack. Before using any of these mounting methods, record the

serial number from the back of the backplane.

Each set of mounting instructions in this document includes an instruction to

connect the protective earth (PE) ground terminal on the cFP-BP-

backplane to

the system safety ground. The backplane PE ground terminal has the following

symbol stamped beside it: . Connect the backplane PE ground terminal to the

system safety ground using 14 AWG (1.6 mm) wire with a ring lug. Use the

5/16 in. panhead screw shipped with the backplane to secure the ring lug to

the backplane PE ground terminal.

What You Need to Get Set Up

• cFP-2120 LabVIEW RT controller

• Mounting hardware (DIN rail, panel-

mount, or rack-mount accessory)

• I/O module(s)

• cFP-BP-

backplane, connector

blocks, cables

• 11–30 VDC power supply

• Accessories: Ethernet cable, number

2 Phillips screwdriver

• PC running Windows

• FieldPoint software 4.1.1 or later

• LabVIEW Real-Time Module

™

cFP-2120 Quick Start Guide 2 ni.com

Caution Keep in mind these requirements for space and cabling

clearance:

• Allow at least 51 mm (2 in.) all around the backplane for air

circulation.

• Allow 38 mm (1.5 in.) below and 51 mm (2 in.) above the controller

for cabling clearance.

Cabling

Clearance

4 slots = 246 mm (9.68 in.)

8 slots = 441 mm (17.4 in.)

Cooling Outline

51 mm (2 in.)

Cooling Outline

51 mm (2 in.)

Min. 182 mm (7.18 in.)

106 mm (4.18 in.)

Cabling

Clearance

Cooling Outline

51 mm (2 in.)

All Around

4 slots = 246 mm (9.68 in.)

8 slots = 441 mm (17.4 in.)

127 mm

(5.00 in.)

Min. 165 mm

(6.50 in.)

National Instruments Corporation 3 cFP-2120 Quick Start Guide

Caution If you are using UL Recognized I\O modules with the

Compact FieldPoint system, you must install the entire system in a

suitably rated, UL Listed NEMA or IP enclosure.

Caution NI recommends that you use one of the mounting systems

described in this document. If you decide to use a custom mounting

solution, make sure that the screws you use are short enough to fit in

the holes in the backplane. The screw holes are 5 mm (0.2 in.) deep.

cFP-2120 Quick Start Guide 4 ni.com

Mounting the Backplane on a Panel

A. Fasten the panel-mount plates to the back of the cFP-BP-

using a number

2 Phillips screwdriver and the 8-32 ×5/16 in. countersink screws shipped

with the kit.

Caution Do not use screws longer than 5/16 in. to fasten the panel-

mount plates to the backplane.

TIONAL

INSTRUMENTS

102 mm

(4 in.)

457 mm (18 in.)

National Instruments Corporation 5 cFP-2120 Quick Start Guide

260 mm (10.25 in.)

102 mm

(4 in.)

104.78 mm

(4.1 in.)

63.50 mm

(2.5 in.)

22.23 mm

(0.9 in.)

33.15 mm

(1.3 in.)

129.54 mm

(5.1 in.)

311.40 mm

(12.3 in.)

387.60 mm

(15.3 in.)

407.80 mm

(16.1 in.)

127.00 mm

(5.0 in.)

440.94 mm

(17.4 in.)

cFP-2120 Quick Start Guide 6 ni.com

B. Bolt or screw the panel-mount accessory to a panel.

C. Connect the PE ground terminal on the cFP-BP-

to safety ground.

Caution Disconnect power before removing the backplane from

the panel.

Mounting the Backplane on a DIN Rail

NI recommends DIN rail mounting for the cFP-BP-4 only. Use panel mounting

or rack mounting for the cFP-BP-8. The DIN rail mounting kit is NI part number

778614-01

A. Fasten the DIN rail clip to the cFP-BP-4 using a number 2 Phillips

screwdriver and the 8-32 ×5/16 in. countersink screws shipped with the

clip.

104.74 mm

(4.1 in.)

63.46 mm

(2.5 in.)

127.00 mm

(5.0 in.)

22.19 mm

(0.9 in.)

34.04 mm

(1.3 in.)

84.84 mm

(3.3 in.)

161.04 mm

(6.3 in.)

211.84 mm

(8.3 in.)

245.87 mm

(9.6 in.)

National Instruments Corporation 7 cFP-2120 Quick Start Guide

Caution Do not use screws longer than 5/16 in. to fasten the DIN rail

clip to the backplane.

B. Insert one edge of the DIN rail into the deeper opening of the DIN rail clip.

C. Press down firmly on the backplane to compress the spring until the clip

locks in place on the DIN rail.

D. Connect the PE ground terminal on the cFP-BP-4 to safety ground.

Caution Disconnect power before removing the backplane from the

DIN rail.

TIONAL

INSTRUMENTS

cFP-2120 Quick Start Guide 8 ni.com

Mounting the Backplane in a Standard 19-in. Rack

A. Fasten the rack-mount bracket to the back of the cFP-BP-

using the

captive screws on the bracket.

TIONAL

INSTRUMENTS

National Instruments Corporation 9 cFP-2120 Quick Start Guide

B. Bolt the rack-mount accessory to a standard 19-in. rack.

C. Connect the PE ground terminal on the cFP-BP-

to safety ground.

Caution Disconnect power before removing the backplane from the

DIN rail.

TIONAL

INSTRUMENTS

cFP-2120 Quick Start Guide 10 ni.com

Install the cFP-2120 Controller on the Backplane

A. Make sure that no power is connected to the controller.

B. Make sure that the cFP-2120 controller is right side up with the NI logo at

the top, and align the captive screws on the controller with the holes on the

backplane.

C. Seat the card edge at the back of the controller in the card-edge connector

on the backplane.

D. Press the controller firmly to seat it on the backplane.

E. Using a number 2 Phillips screwdriver with a shank of at least 64 mm

(2.5 in.) length, tighten the captive screws to 1.1 N ⋅m (10 lb ⋅in.) of torque.

TIONAL

INSTRUMENTS

Indice

Altri manuali National Instruments Controllori

National Instruments

National Instruments IC-3173 Manuale utente

National Instruments

National Instruments Motion Control 7344 Manuale utente

National Instruments

National Instruments NI cRIO-9025 Manuale utente

National Instruments

National Instruments PXIe-8840 Quad-Core Manuale utente

National Instruments

National Instruments sbRIO-9638 Manuale utente

National Instruments

National Instruments Network Adapter NI PXIe-6672 Manuale utente

National Instruments

National Instruments 73 Series Manuale utente

National Instruments

National Instruments PXI-8186 Manuale utente

National Instruments

National Instruments IC-3121 Manuale utente

National Instruments

National Instruments cRIO-9034 Manuale utente

National Instruments

National Instruments PXI NI PXI-8105 Manuale utente

National Instruments

National Instruments cRIO-9034 Manuale utente

National Instruments

National Instruments CompactRIO cRIO-9002 Manuale utente

National Instruments

National Instruments NI-488.2 Manuale utente

National Instruments

National Instruments RMC-8356 Manuale utente

National Instruments

National Instruments PXI-8150 Series Manuale utente

National Instruments

National Instruments 3100 Manuale utente

National Instruments

National Instruments NI cRIO-9065 Manuale utente

National Instruments

National Instruments cRIO-9075 Manuale utente

National Instruments

National Instruments cRIO-9037 Manuale utente

National Instruments

National Instruments PXI-8119 Manuale utente

National Instruments

National Instruments PXIe-8106 Manuale utente

National Instruments

National Instruments myRIO-1950 Manuale utente

National Instruments

National Instruments NI PXIe-8840 Manuale utente

Manuali Controllori popolari di altre marche

Digiplex

Digiplex DGP-848 Istruzioni operative

YASKAWA

YASKAWA SGM series Manuale utente

Sinope

Sinope Calypso RM3500ZB Manuale utente

Isimet

Isimet DLA Series Style 2 Manuale di installazione

LSIS

LSIS sv-ip5a Manuale utente

Rockwell Automation

Rockwell Automation 1769-L31 Manuale utente

Airflow

Airflow Uno hab Manuale utente

ABB

ABB ACS580-01 drives Manuale utente

Panasonic

Panasonic GM1 Series Manuale utente

Emerson

Emerson SW93 Manuale utente

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuale utente

Panasonic

Panasonic FP? Positioning Unit RTEX Manuale utente

Samson

Samson Type 5824 Manuale di servizio

Alpha IP

Alpha IP MIOB 21001 Manuale utente

Siemens

Siemens OpenAir GMA 1 Series Manuale utente

Surecom

Surecom SR-629 Manuale utente

Fishman

Fishman TriplePlay Manuale utente

Regulus

Regulus SRS1 T Manuale utente