NEC N8151-101 Manuale utente

N8151-101

Built-In LTO

User’s Guide

Note

Before using the N8151-101 Built-In LTO, read this User’s Guide

carefully.

Keep this User’s Guide at hand for quick reference at any time

necessary.

TRADEMARKS

Microsoft and the Microsoft logo, Windows and Windows Server are registered trademarks or

trademarks of Microsoft Corporation in the United States and other countries.

Liner Tape-Open, LTO, Ultrium Tape Drive are registered trademarks of Hewlett-Packard Company

and Seagate Technology, Inc. in the United States and other countries.

The company and product names contained in this manual are trademarks or registered trademarks

of the respective companies.

All names used in the sample applications are fictitious. They have no relation with any product, party

or individual names.

Remarks

(1) Reproduction of this document or portions thereof without prior approval is prohibited.

(2) The information contained in this document is subject to change at any time, without prior notice.

(3) Reprinting or changing of this document without prior approval of NEC is prohibited.

(4) All efforts have been made to ensure that the contents of this manual are correct; however,

should any doubts arise, or errors or missed entries be detected, NEC would greatly appreciate it

if our dealers are informed about it.

(5) Please note that in no event shall NEC be liable for any damages whatever arising out of the use

of this device, regardless of item (4) above.

Keep this User's Guide at hand for quick reference at anytime necessary.

Safety Considerations - Must Read -

Follow the instructions given in this User's Guide for proper operations and safe use of the

device.

For the terms used in this User's Guide, please refer to “Part Name and Function”section

of this document.

SAFETY INDICATIONS

This User's Guide describes the device components with possible danger, hazards that

may be caused by ignoring warnings, and preventive actions against such hazards.

Components with possible danger are indicated with a warning label placed on or around

them. In the User's Guide or warning labels, "WARNING" or "CAUTION" is used to indicate

a degree of danger. These terms are defined as follows:

Failure to heed this sign could result in serious injury or death.

Failure to heed this sign could result in personal injury or damage to properties.

Precautions and notices against hazards are presented with one of the following three

symbols. The individual symbols are defined as follows:

Attention This symbol indicates the presence of a hazard if

the instruction is ignored. An image in the symbol

illustrates the hazard type.

(Sample)

(Electric shock)

Prohibited

Action This symbol indicates prohibited actions.

An image in the symbol illustrates a particular

prohibited action.

(Sample)

(Do not touch the part)

Mandatory

Action This symbol indicates mandatory actions.

An image in the symbol illustrates a mandatory

action to avoid a particular hazard.

(Sample)

(Disconnect the

power cord)

(Sample)

A symbol for arousing

attention A content of possible

danger Aterm indicating a hazard level

Do not install the device while the power is turned on.

Unplug the AC power cord from the main power source when installing/uninstalling

the device to/from server or connect it with the enclosure. Failure to follow this

warning may cause an electric shock.

SYMBOLS USED IN THIS USER'S GUIDE AND WARNING

LABELS

Attention

Indicates that improper use may

cause an electric shock. Indicates that improper use may

cause fumes or fire.

Indicates that improper use may

cause fingers to be caught. Indicates a general notice or warning

that cannot be specifically identified.

Indicates a possibility of getting

damage by high temperature.

Prohibited Action

Indicates a general prohibited action

or warning that cannot be specifically

identified.

Do not disassemble, repair, or modify

the device. Otherwise, an electric

shock or fire may be caused.

Mandatory Action

Unplug the power cord. Otherwise,

an electric shock or fire may be

caused.

Indicates a general mandatory action

or warning that cannot be specifically

identified.

SAFETY NOTES

This section provides several precautions to enable you to use the product safely and

correctly and to prevent injury and property damage. Read this section carefully to ensure

proper and safe use of the product. For symbols, see "SAFETY INDICATIONS" provided

earlier.

General Attention

Do not use in life-critical applications or applications requiring high reliability.

This device is not intended for integration with or control of facilities or equipment

that may affect human life or that require a high degree of reliability, such as

medical equipment, nuclear power facilities, aerospace instruments, and

transportation equipment. The manufacturer does not assume any liability for

accidents resulting in injury or death, or for any damages to property that may occur

as a result of using this device in such facilities, equipment, or control systems.

Do not use the Built-in LTO if any smoke, odor, or noise is present.

If smoke, odor, or noise is present, immediately turn off the POWER switch and

disconnect the power plug from the outlet, then contact your sales agent. Using the

Built-in LTO in such conditions may cause a fire.

Keep needles or metal objects away from the Built-in LTO.

Do not insert needles or metal objects into ventilation holes in the Built-in LTO.

Failure to follow this warning may cause an electric shock.

Keep water or foreign matter away from the Built-in LTO.

Do not let any kind of liquid (water etc.) or foreign matter (e.g., pins or paper clips)

enter the Built-in LTO. Failure to follow this warning may cause an electric shock, a

fire, or a failure of the Built-in LTO. When such things accidentally enter the Built-in

LTO, immediately turn off the power and disconnect the power plug from the outlet.

Do not disassemble the Built-in LTO. Contact your sales agent.

Attention to Power or Power Cord

Do not hold the DC cable with a wet hand.

Do not disconnect/connect the cable while your hands are wet. Failure to follow this

warning may cause an electric shock.

Do not install the device while the power is turned on.

Unplug the AC power cord from the main power source when installing/uninstalling

the device to/from server or connect it with the enclosure. Failure to follow this

warning may cause an electric shock.

Insert the DC cable into the outlet as far as it goes.

Heat generation resulting from a halfway inserted DC cable (imperfect contact) may

cause a fire. Heat will also be generated if condensation is formed on dusty blades

of the halfway inserted cable, increasing the possibility of a fire.

Do not connect the Built-in LTO by unspecified cabling.

Connecting or cabling with DC cable should be done in accordance with the

procedure specified in the User's Guide.

Unspecified connecting or cabling may cause an electric shock or a fire.

Do not use any damaged power cord.

If the power cord is damaged, immediately replace it with a new part of same type.

Do not repair the damaged section for reuse. Otherwise, the section repaired with

vinyl tape or the like will be overheated to cause an electric shock or a fire.

Use the authorized cable only.

Use only the specified cable when connecting the Built-in LTO with a server. Use of

an unspecified cable or connection by unspecified cabling may cause a fire.

Attention to Installing, Moving, Storing, Connection

Do not close the ventilation hole.

Do not close the ventilation hole in the front side of the Built-in LTO. Otherwise, its

internal temperature will rise to cause malfunctions or a fire.

Do not connect/disconnect the interface cables before unplugging the power

plug.

Before connecting/disconnecting the interface cables, disconnect the power plug of

the main power unit from the outlet. If the power is off but the power plug is still

connected, you may get an electric shock.

Do not use the unspecified interface cables.

Uses only the cable authorized by NEC and locate the device and connector before

connection. Use of an unauthorized cable or displaced connection may cause a

short circuit, resulting in a fire.

When handling or connecting the interface cables, keep the notes as follows:

Do not tread on cables.

Do not load on the cable.

Insert the cable connector as far as it goes.

Do not use damaged cables.

Do not use damaged connectors.

Make sure that screwing or the like is done firmly.

Do not use or keep in the environment where corrosive gas exists.

Do not use Built-in LTO Auto Loader, installing in the environment where corrosive

gas (sulfur dioxide, hydrogen sulfide, nitrogen dioxide, chlorine, ammonia, ozone,

etc.) exists.

In addition, do not set it up in the environment including the element (sodium

chloride and sulfur, etc.) that promotes corrosion in dust and air, and the

electro-conductive metal etc. The print plate in the device corrodes, and it might

cause the breakdown and smoking and the ignition.

When there is the above-mentioned doubt in the environment of use, please consult

with a store or a maintenance service company.

Avoid installation in extreme temperature condition.

Immediately after the power supply of the server is turned off, components in the

server including the internal hard disk drive or others are hot. Please install/detach

the device after confirming it is cold enough.

Attention to Handling or Maintenance

Do not disassemble, repair, or alter the Built-in LTO.

Never attempt to disassemble, repair, or alter the Built-in LTO on any occasion other

than described in this User's Guide. Failure to follow this instruction may cause an

electric shock or a fire as well as malfunctions of the Built-in LTO.

The following can be performed by the Built-in LTO user. Do not perform any other

type of disassembly than described here.

Remove or install brackets

Remove or install the DC signal cable

Do not handle while the power plug is connected.

Before handling or cleaning the Built-in LTO, disconnect the power plug of the main

power unit from the outlet. If the power is off but the power plug is still connected,

you may get an electric shock.

Insert the cables into the connectors as far as it goes.

Heat generation resulting from a halfway inserted cables or Interface cables

(imperfect contact) may cause a fire. Heat will also be generated if condensation is

formed on dusty blades of the halfway inserted cable, increasing the possibility of a

fire.

Attention to Operation

Do not insert your hands into the cartridge load compartment.

Do not insert your hands into the cartridge load compartment. Otherwise, the fingers

will be caught/pinched by the Built-in LTO to cause an injury.

Do not touch the Built-in LTO when it thunders.

If it starts thundering, do not touch any part of the Built-in LTO. Failure to follow this

warning may cause an electric shock or a fire.

Keep away pets.

Keep away pets from the Built-in LTO. Insertion their hair or excrements may cause

afire or an electric shock.

FOR PROPER OPERATION

To operate the Built-in LTO correctly, observe the following points.

For considerations on handling the data cartridge, refer to the chapter "Data Cartridge".

Do not turn off the server when the LED on the front of the Built-in LTO is blinking.

This may cause a machine failure or damage of backup data.

Do not store the Built-in LTO in a place subject to corrosive gas, chemicals, or

splash of chemicals.

Built-in LTO parts may be deformed or damaged and may not be able to

operate correctly.

Do not store the Built-in LTO in a place subject to strong vibrations.

This may cause the Built-in LTO to be defected.

As the data cartridge set in the Built-in LTO, use our "Data Cartridge."

If you use a data cartridge of other manufacturer, a read/write error may

occur.

Any data cartridge cannot be used as the system disk.

This may cause the OS to be started unsuccessfully and/or the data in the

data cartridge to be broken.

Do not disassemble data cartridges.

This may cause the data stored in the data cartridge to be broken. Inserting a

data cartridge having been disassembled into the Built-in LTO may cause the

Built-in LTO to be defected.

Do not bring a substance which generates magnetism close to data cartridges.

This cause the data stored in the data cartridges may be broken.

Eject the data cartridge when you are done performing a backup.

This may shorten the operational life of the data cartridge and/or case

malfunctions.

Indice

Altri manuali NEC Hardware per computer

Manuali Hardware per computer popolari di altre marche

EMC2

EMC2 VNX Series Manuale del proprietario

Panasonic

Panasonic DV0PM20105 Manuale utente

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuale utente

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuale utente

Raidon

Raidon iT2300 Manuale utente

National Instruments

National Instruments PXI-8186 Manuale utente

Hauppauge

Hauppauge WinTV-HVR-2250 Manuale utente

Kontron

Kontron CP6002 Manuale utente

Manhattan

Manhattan 702843 Manuale utente

Aphex

Aphex 230 Manuale utente

AMD

AMD Phenom II Manuale operativo

Intel

Intel NUC 12 Pro Manuale utente

dbx

dbx Zone Pro 1260 Manuale utente

Galaxy

Galaxy GHDX2-2430S-24F4D Manuale utente

Intel

Intel AXXRMFBU4 Manuale utente

Kontron

Kontron DIMM-PC/MD Manuale utente

ST X-NUCLEO-SAFEA1B Istruzioni operative

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuale utente