NetComm NTC-400 Series Manuale utente
Quick Start Guide
NTC-400 Series Router
| Industrial IoT
2
This quick start guide is designed to get you up and running quickly and familiarise
you with the NTC-400 Series router. More advanced set up instructions are
provided in the user guide which can be downloaded from
http://www.netcommwireless.com/product/m2m/ntc-400
| Industrial IoT
3
NTC-400 Series Router
Package contents
The NTC-400 Series package includes:
1 x NTC-400 Series Router
2 x Wall mounting
brackets
1 x Quick Start Guide
2 x 2.4GHz / 5GHz
WiFi antennas
4 x Wall mounting
bracket screws
1 x 8-pin Terminal block
Pre-requisites
To complete the installation, you may require certain items such as screwdrivers
and fasteners.
2 x Cellular antennas
| Industrial IoT
4
Terminal block
The 8-pin Terminal block provides the following interfaces:
1 3 5 7
2 4 6
1. Power (PWR)
2. Ground (GND)
3. Ignition (IGN)
4. Digital Input 1 (DI-1)
5. Digital Input 2 (DI-2)
6. Digital Output (DO)
7. RS232 Serial (TX/RX)
| Industrial IoT
5
NTC-400 Series Router
I/O specications
MODE
SPECIFICATIONS
Digital Input
(DI-1 and DI-2)
Trigger voltage (high) Logic level 1: 5 V to 30 V
Normal voltage (low) Logic level 0: 0 V to 1.0 V
Digital Output
(DO)
Voltage (Relay mode)
Logic level 1: Depends on external device.
Maximum voltage is 36 V.
Logic level 0: Floating, External pull-down
resister (10 k Ω, 0.5 W) is required.
Note: DO power is relayed from the PWR
pin on the 8-pin terminal block connector.
Maximum current 1 Amp @ 12 V, or 0.33 Amp @ 36 V
Power requirements
The NTC-400 Series router accepts DC power in the range of 9 V to 36 V. Follow
the above illustration to ensure that the power source is connected with the
correct polarity.
| Industrial IoT
6
SIM cards
SIM cards are inserted into the SIM slots located on the front panel of the device.
To access the SIM card slots, remove the protective plate using a screwdriver.
NOTE: SIM B is disabled on units purchased through Telstra. On these units,
insert the SIM card into slot A.
| Industrial IoT
7
NTC-400 Series Router
Conguring the router
The web interface can be accessed via WiFi or Ethernet.
Connecting via WiFi
1. Connect and power up the NTC-400 Series router.
2. On your client device (e.g. laptop, tablet), connect to the SSID labelled
“NetComm_2.4GHz_XXXX” or “NetComm_5GHz_XXXX” where “XXXX” is four
randomly generated digits. The unique SSID and password for the wireless
networks are printed on the back cover of this Quick Start Guide and on the
label afxed to the bottom of the device. Enter the WiFi password and then
continue to the “Accessing the web interface” section.
Connecting via Ethernet cable
1. Connect and power up the NTC-400 Series router.
2. Connect a standard straight-through Ethernet cable to your client PC and the
other end to any of the LAN ports on the back of the NTC-400 Series router.
Continue to the “Accessing the web interface” section.
Accessing the web interface
3. In a web browser on your client device, navigate to http://192.168.20.1
4. Enter the username and password printed on both the back cover of this
Quick Start Guide and on the label afxed to the bottom of the device, then
press Enter or the click the Login button. Refer to the User Guide for further
conguration instructions.
NOTE: We highly recommend that you secure the WiFi networks
upon initial installation and change the password used to access
the web interface.
| Industrial IoT
8
Unlocking the SIM card
If the inserted SIM card is PIN locked, navigate to Basic Network >
WAN & Uplink > WAN Interface IPv4 Network Status > WAN-1 > Edit >
Internet Setup > WAN-1 > Edit > Connection with SIM-A / SIM B card >
PIN Code to enter the PIN Code. Click the Save button to save your changes.
NOTE: SIM B is disabled on units purchased through Telstra. On these units,
congure the SIM card in slot A.
| Industrial IoT
9
NTC-400 Series Router
Updating the APN
The default connection proles for both SIM-A and SIM-B are congured for
automatic conguration. If you wish to congure the APN manually, navigate to
Basic Network > WAN & Uplink > WAN Interface IPv4 Network Status
> WAN-1 > Edit > Internet Setup > WAN-1 > Edit > Connection with
SIM-A / SIM B card, set Dial-Up Prole to “Manual-conguration” and enter
the APN into the APN eld. Click the Save button to save your changes.
NOTE: SIM B is disabled on units purchased through Telstra. On these units,
congure the SIM card in slot A.
| Industrial IoT
10
Verifying the
connection status
When the NTC-400 Series router is connected to the Internet, the “HIGH” or “LOW”
LED on the front of the device lights up to indicate the current signal strength.
To check the connection status from the web interface, navigate to Status >
Dashboard and conrm that there is a 3G/4G Interface displayed under the
Network Interface Status table.
Altri manuali per NTC-400 Series
1
Indice
Altri manuali NetComm Router di rete
NetComm
NetComm AV SERIES Manuale utente
NetComm
NetComm NTC-220 Guida rapida
NetComm
NetComm NB16WV Manuale utente
NetComm
NetComm NB1300 Istruzioni di installazione e manutenzione
NetComm
NetComm N300 GATEWAY SERIES Manuale utente
NetComm
NetComm N3G007W Manuale utente
NetComm
NetComm NB3100 Manuale utente
NetComm
NetComm NB702 SHDSL Manuale utente
NetComm
NetComm NB6PLUS4W Guida per l'amministratore
NetComm
NetComm NB9WMAXXn Manuale utente
NetComm
NetComm NB8 Manuale utente
NetComm
NetComm NF10W Manuale utente
NetComm
NetComm NF20 Manuale utente
NetComm
NetComm NF8AC Come usare
NetComm
NetComm NTC-140-02 Manuale utente
NetComm
NetComm NB6 Manuale utente
NetComm
NetComm Whitepaper TR-069 Manuale utente
NetComm
NetComm NB16WV-02 Manuale utente
NetComm
NetComm NB9WMAXX Manuale utente
NetComm
NetComm Freshtel NB9 Manuale utente
Manuali Router di rete popolari di altre marche
NETGEAR
NETGEAR FS526T - Switch Manuale utente
Korenix
Korenix JetNet 5710G Series Manuale utente
Automated Logic
Automated Logic ZN551 Manuale del proprietario
Cisco
Cisco ASR 1000 Series Manuale dell'operatore
EnGenius
EnGenius ESR-9710 Manuale utente
Cisco
Cisco 805 Series Istruzioni operative e di sicurezza