Netum NT-1203 Manuale di istruzioni

Model NT-1203 With SPP Mode

Get Started: This is 1D and 2D bluetooth scanner. Follow below "bluetooth connection"

instruction to pair with your device and then setup the keyboard language (if you US

keyboard, you can skip this step). After that the scanner can start to read and upload

the barcodes. If you want to do other configurations please refer to programming

barcodes.

Low voltage Alarm: Scanner will make 3x beeps (even you just trigger the button and

do not scan any barcodes) to remind you that it's under low voltage. Please connect

the base with your device via USB cable ,then put the scanner on the base to charge

power for it.

Barcode Programming

Netum barcode scanners are factory programmed for the most common terminal and

communications settings. If you need to change these settings, programming is

accomplished by scanning the bar codes in this guide. An asterisk (*) next to an option

indicates the default setting.

Important Note: There will not have a beep sound for some of configuration but as

long as light turns off a few seconds before you release the trigger button that

indicates the scanner has read the codes successfully.

Bluetooth Connection

1. Pairing with windows XP or Windows 7/8/10

Power on the scanner , a few seconds later the blue indicator will keep flashing.

Enter the ‘Control Panel’ - ‘Devices and Printers’ - ‘Add a device’ –select,

‘Bluetooth’ to add the device to your computer

Click ‘Next’, the scanner will beep to indicate a successful pairing, and the light will turn

to solid blue.

2. Android: Connect Android Device in Basic Mode

Power on the scanner. Make sure the scanner is discoverable (unpaired). a few seconds

later the blue indicator will keep flashing.

Touch Home | Menu | Settings | Wireless & Networks | Bluetooth settings

Make sure the device has Bluetooth “On”. Scan for devices.

In the list of found devices, select “Netum Bluetooth”. Tap Pair.

The scanner will connect to the Android device.

The scanner will beep once after it has connected and is ready to scan barcodes.

3. Pairing with your IOS device

Power on the scanner. Make sure the scanner is discoverable (unpaired). a few seconds

later the blue indicator will keep flashing.

Click on “Bluetooth” in the left column. Your IOS device will automatically start

searching for

any Bluetooth Devices in the area.

Once you have identified the “Netum Bluetooth” on the screen, tap on it and

you will automatically be connected. The scanner’s LED light will turn solid

blue.

Note: SPP mode can not work on IOS System

Keyboard Language

Keyboard layouts vary from country to country. The default setting is U.S. keyboard.

In order to let scanner upload the codes in a correct way, you have to set the keyboard

language.

For example If you use French Keyboard, scan below barcode of “French keyboard”. Then the

scanner will upload barcodes according to French keyboard layout. American Keyboard is set by

default, if you use a US keyboard you can ignore this part.

American Keyboard Portugal Keyboard

French Keyboard Spanish Keyboard

Germany Keyboard Turkey Q Keyboard

Italy Keyboard

Scanning Mode

Note that there will not have beep sound when you set below modes. As long as light turns off a few

seconds before you release the trigger button that indicate the configuration has been done.

Key Holding

Press the button to trigger the reading, release the button to end the reading. Reading success or reading

time over a single reading time will end the reading

Continuous Mode

The reading engine performs continuous work. Reading success of reading time over a single reading time

will end the reading. More than the specified time will automatically trigger the next reading.

Automatic Induction Mode

In automatic induction mode, the scan engine detects the brightness of the surroundings. Trigger reading

when the brightness changes. Reading success or reading time over a single reading time will end the

reading. Regardless of the last success of failure to read. Re-enter the detection of the surrounding

environment brightness.

Factory Default Configuration

This confirguration including four steps. Please scan below codes one by one . Note that there will not have a

beep sound after you scan code of “default configuration ”.As long as light turns off a few seconds before you

release the trigger button that means scanner has read the codes successfully. keep scanning the following

codes until last one to finish the default configuration.

Step 1 : Factory default

303FFF3

Step 2 : Enable Code 39

1000111

Step3 : Serial Port

3030010

Step 4 : Baud Rate 19200

2090107

Custom prefix and suffix

Custom Prefix Custom Suffix 1

Custom Suffix 2

Please note previous prefix or suffix will be cleared once you start to add new prefix or suffix.

Scan Data Transmission Format

To change the Scan Data Transmission Format, scan one of the eight bar codes corresponding to the desired

format.

*Data As Is <DATA><SUFFIX 1>

Appendix 1

Numeric Bar Codes For parameters requiring specific numeric values, scan the appropriately numbered bar

code(s).

For Example

Custom @ as prefix

Step 1: scan “custom prefix”

Custom Prefix

Step 2: To set these values, scan a four-digit number (i.e. four bar codes) that corresponds to ASCII values. See

Numeric Bar Codes in appendix 1. Scan 1043(@) one by one.

Step 4: Set Data Transmission Format

Custom Suffix

Step 1: scan “custom suffix”

Scan Suffix 1

Step 2 and Step 3 same procedures like custom prefix

Step 4: Set Data Transmission Format

Enable Keystroke*/ Functional Key Set

Enable Keystroke* Enable functional Key Set

For example if you scan value 1004, Keystroke will be “Up Down”.

But if you scan Enable Functional Key Set after you scan the value ”1004”, you will get functional key set Ctrl

+D. For more details please refer to Appendix 1.

Altri manuali per NT-1203

Indice

Manuali Lettore di codici a barre popolari di altre marche

POSMicro

POSMicro Datalogic PowerScan D7100 Manuale utente

Marson

Marson MT780 Guida rapida alla configurazione

NCR

NCR RealPOS Manuale utente

Motorola

Motorola SE3300 Guida rapida alla configurazione

Element

Element P130BT Manuale utente

Motorola

Motorola Symbol LS3008 Manuale di installazione e funzionamento

Meec tools

Meec tools OBD-II / VAG Manuale utente

SICK

SICK CLP 100 Manuale utente

Royal Tag SA

Royal Tag SA I-Read Manuale utente

Welch Allyn

Welch Allyn IMAGETEAM 3800 Manuale utente

Meteor

Meteor 8310 Manuale utente

Denso

Denso BHT-500B Manuale utente

Datalogic

Datalogic Heron HD3130 Manuale utente

Motorola

Motorola MP6000 Istruzioni di montaggio

Newland

Newland NLS-HR15-BT Manuale utente

ARTDEV

ARTDEV AS-1310 Manuale utente

Aopos

Aopos AS290 Manuale utente

ENS

ENS 367-5455 Manuale utente